Hotpoint HTX26EASWWW Installation Instructions

Hotpoint HTX26EASWWW Manual

Get Hotpoint HTX26EASWWW PDF manuals and user guides View all Hotpoint HTX26EASWWW manuals
Add to My Manuals
Save this manual to your list of manuals

Hotpoint HTX26EASWWW manual content summary:

  • Hotpoint HTX26EASWWW | Installation Instructions - Page 1
    or metal foil duct and replace with UL-listed duct. • Service information and the wiring diagram are located in the control console. listed and installed in accordance with the instructions found in "Connecting the Dryer to House Vent" later in this manual. Flexible venting materials are known to
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 2
    Installation Instructions UNPACKING YOUR DRYER Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking them away from the dryer
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 3
    Installation Instructions REQUIREMENTS FOR ALCOVE OR CLOSET INSTALLATION WARNING - Explosion rear 0" front 1" top • Consideration must be given to provide adequate clearance for installation and service. • Closet doors must be louvered or otherwise ventilated and have at least 60 square inches
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 4
    Installation Instructions CONNECTING INLET HOSES (for steam dryer models only) CONNECTING INLET HOSES To produce steam, the dryer must connect to the cold water supply. Since the
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 5
    Installation Instructions CONNECTING A GAS DRYER (skip for electric dryers) TOOLS YOU WILL NEED Ŷ 10" Adjustable wrenches (2) Ŷ Flat-blade screwdriver • Before beginning the installation, turn off the circuit
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 6
    Instructions CONNECTING A GAS DRYER (cont.) GAS REQUIREMENTS WARNING - Explosion Hazard • Use a new CSA International approved flexible gas supply line. Never reuse old flexible connectors. • Install an individual manual gas company personnel, and authorized service personnel. • Failure to do
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 7
    Installation Instructions CONNECTING A GAS DRYER (cont.) CONNECTING THE DRYER TO THE GAS SUPPLY A Install a female 3/8" NPT elbow at the end of the dryer gas inlet. Install a 3/8" flare
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 8
    risk of electric shock. Check with a qualified electrician, or service representative or personnel, if you are in doubt as to the outlet, have a proper outlet installed by a qualified electrician. SAVE THESE INSTRUCTIONS • If required by local codes, an external 18 gauge or larger copper ground
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 9
    Installation Instructions CONNECTING AN ELECTRIC DRYER (Skip for gas dryers and if your dryer already has a power cord attached) TOOLS YOU WILL NEED Ŷ Flat-blade screwdriver Ŷ Slip-
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 10
    to do so can result in death, fire or electrical shock. GROUNDING INSTRUCTIONS For a grounded, cord-connected dryer: This dryer must be grounded. In in a risk of electric shock. Check with a qualified electrician, or service representative or personnel, if you are in doubt as to whether the
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 11
    Installation Instructions CONNECTING AN ELECTRIC DRYER CONNECTING DRYER USING 4-WIRE CONNECTION (MUST BE USED FOR MOBILE HOME INSTALLATION) NOTE: Since January 1, 1996, the National Electrical Code requires
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 12
    longer than specified in the exhaust length table. Failure to follow these instructions can result in death or fire. TOOLS AND MATERIALS YOU WILL NEED TO cm) duct PARTS AVAILABLE FROM GEAPPLIANCEPARTS.COM OR LOCAL SERVICE ORGANIZATIONS PM8X85 Outdoor exhaust hood PM08X10085 8' Flexible metal
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 13
    Installation Instructions EXHAUSTING THE DRYER (cont.) • DO cut duct as short as Accumulate lint, creating a potential fire hazard. The correct exhaust installation is YOUR RESPONSIBILITY. Problems due to incorrect installation are not covered by the warranty. The MAXIMUM ALLOWABLE length of
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 14
    Installation Instructions EXHAUSTING THE DRYER (cont.) EXHAUST SYSTEM CHECKLIST HOOD OR WALL CAP • Terminate in a manner to prevent back drafts or entry of birds or other wildlife. •
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 15
    Installation Instructions EXHAUSTING THE DRYER (cont.) SIDE OR BOTTOM VENTING WARNING - Fire Hazard Disconnect dryer from electrical supply. Wear gloves and arm guards. Close the back opening
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 16
    Installation Instructions EXHAUSTING DRYER (cont.) FINAL SETUP SIDE OR BOTTOM VENTING (cont.) ADDING parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel - DO NOT contact the following parts while the appliance is energized: drum
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 17
    do not move the cabinet until door swing reversal is completed. These instructions are for changing the hinges from the right side to the left side . Loosen each top hinge screw on right side Choose the REVERSING THE DOOR instructions A or B for your model. A REVERSING THE DOOR - SOLID DOOR MODELS
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 18
    Installation Instructions REVERSING THE DOOR (cont.) A REVERSING THE DOOR - SOLID DOOR MODELS (cont.) 5 GTX52 model panel NOTE: To return the door to the original setup, follow these instructions, swapping "left" and "right". When you finish Plug the dryer back into its electrical outlet. 18
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 19
    Installation Instructions REVERSING THE DOOR B REVERSING THE DOOR - GLASS PANEL DOOR MODELS 1 Open the door approximately 130 degrees. With a putty knife, remove the 4 plastic caps located along
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 20
    Installation Instructions REVERSING THE DOOR (cont.) B REVERSING THE DOOR - GLASS PANEL DOOR MODELS (cont.) 6 of front panel NOTE: To return the door to the original setup, follow these instructions, swapping "left" and "right". When you finish Plug the dryer back into its electrical outlet. 20
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 21
    ), debe estar aprobado por UL e instalarse de acuerdo con las instrucciones de "Cómo conectar la secadora a la ventilación doméstica" de este manual. Los materiales de los conductos flexibles a menudo se desploman, se aplastan y atrapan pelusas. Estas condiciones obstruyen la corriente de aire de la
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 22
    Instrucciones de instalación CÓMO DESEMPACAR LA SECADORA Incline la secadora de costado y saque los soportes de espuma de embalaje tirando de los costados y quitándolos de las patas de la secadora. Asegúrese de quitar todas las piezas de espuma de las patas. Saque la bolsa que contiene la informaci
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 23
    Instrucciones de instalación REQUERIMIENTOS - INSTALACIÓN EN NICHOS O ARMARIOS ADVERTENCIA - Riesgo de explosión Mantenga cualquier material y vapores inflamables, tales como gasolina, alejados de la secadora. Coloque la secadora a por lo menos 18" (46 cm.) del piso cuando sea instalada en un
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 24
    Instrucciones de instalación CÓMO CONECTAR MANGUERAS DE ENTRADA (sólo para los modelos de secadoras de vapor) CÓMO CONECTAR MANGUERAS DE ENTRADA Para producir vapor, la secadora debe conectarse al suministro de agua fría. Ya que la lavadora también debe conectarse al agua fría, debe introducirse un
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 25
    Instrucciones de instalación CÓMO CONECTAR UNA SECADORA A GAS (si se cuenta con una secadora eléctrica, saltear este paso) HERRAMIENTAS NECESARIAS Ŷ Llaves ajustables de 10" (2) Ŷ Destornillador de lados planos • Antes de comenzar la instalación, apague el disyuntor o quite los fusibles de la
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 26
    nea nueva de suministro de gas flexible que esté aprobada por CSA International. Nunca vuelva a usar conectores flexibles viejos. • Instale una válvula de cierre manual individual dentro de 6 pies de la secadora en acuerdo con el Código Nacional de Gas Combustible, ANSI Z223.1 / NFPA 54. • De forma
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 27
    Instrucciones de instalación CÓMO CONECTAR UNA SECADORA A GAS (cont.) CÓMO CONECTAR LA SECADORA AL SUMINISTRO DE GAS A Instale un codo hembra NPT de 3/8" al final de la entrada de gas de la secadora. Instale un adaptador de unión cónica de 3/8" al codo hembra. IMPORTANTE: Utilice una llave para
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 28
    Instrucciones de instalación CÓMO CONECTAR UNA SECADORA A GAS (cont.) PRUEBA DE PÉRDIDAS Nunca utilice una llama abierta para detectar pérdidas de gas. Controle todas las conexiones con una solución jabonosa o un elemento equivalente. Aplique una solución jabonosa. La solución para controlar pé
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 29
    Instrucciones de instalación CÓMO CONECTAR UNA SECADORA ELECTRICA (Sáltese si se trata de las secadoras a gas o si su secadora ya tiene un cable de alimentación conectado) HERRAMIENTAS NECESARIAS Ŷ Destornillador de lados planos Ŷ Pinzas Ŷ Destornillador Phillips Ŷ Nivel Antes de efectuar la
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 30
    Instrucciones de instalación CÓMO CONECTAR SECADORA ELECTRICA CONEXIÓN ELÉCTRICA INFORMACIÓN SOBRE LAS SECADORAS ELÉCTRICAS Para realizar conexiones eléctricas con un cable de corriente: NOTA: Si el circuito de su secadora está en un circuito protegido por un interruptor GFCI, no se permite la
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 31
    Instrucciones de instalación CÓMO CONECTAR SECADORA ELECTRICA CÓMO CONECTAR LA CÓMO CONECTAR LA SECADORA SECADORA USANDO UNA CONEXIÓN DE 4 CABLES (DEBE UTILIZARSE EN INSTALACIONES DE CASAS RODANTES) UTILIZANDO UNA CONEXIÓN DE 3 CABLES NOTA: Si el circuito de su secadora está en un circuito
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 32
    Instrucciones de instalación SALIDA AL EXTERIOR DE LA SECADORA ADVERTENCIA - Riesgo de incendio Esta secadora DEBE tener una ventilación al exterior. Utilice sólo un conducto de metal rígido de 4" para la ventilación de salida doméstico. Use sólo un conducto de transición de la secadora de metal
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 33
    Instrucciones de instalación SALIDA AL EXTERIOR DE LA SECADORA (cont.) • CORTE el conducto lo más corto posible e instálelo derecho en la pared. • UTILICE codos cuando hagan falta curvas. Codos • NO doble o pliegue los conductos. Utilice codos si algunos codos resultan necesarios. • NO utilice
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 34
    Instrucciones de instalación SALIDA AL EXTERIOR DE LA SECADORA (cont.) LISTA DE CONTROL DEL SISTEMA DE SALIDA CAMPANA O CUBIERTA DE PARED • Instale la salida de modo de evitar contracorrientes o el ingreso de pájaros u otros insectos o animales. • La boca de salida debe presentar una resistencia
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 35
    Instrucciones de instalación SALIDA AL EXTERIOR DE LA SECADORA (cont.) VENTILACIÓN LATERAL O POR LA PARTE INFERIOR ADVERTENCIA - Riesgo de incendio Desconecte la secadora del suministro eléctrico. Use guantes y protectores para brazos. Cierre la abertura trasera con la placa protectora (Kit
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 36
    Instrucciones de instalación SALIDA AL EXTERIOR DE LA SECADORA (cont.) VENTILACIÓN LATERAL O POR LA PARTE INFERIOR (cont.) CÓMO AGREGAR CODOS Y CONDUCTOS DE SALIDA HACIA LA IZQUIERDA O DERECHA DEL GABINETE (cont.) • Aplique cinta papel de aluminio como puede verse en la junta entre el conducto
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 37
    Instrucciones de instalación INVERSIÓN DE LA PUERTA Cómo cambiar el sentido de apertura de la puerta. NOTAS IMPORTANTES: • Lea todas las instrucciones antes de comenzar. • Manipule las piezas con cuidado para evitar rayar la pintura. • Coloque los tornillos cercanos a sus piezas correspondientes
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 38
    Instrucciones de instalación INVERSIÓN DE LA PUERTA (cont.) A INVERSIÓN DE LA PUERTA MODELOS DE PUERTA SÓLIDA (cont.) 5 Solo modelo GTX52: Quite las dos bisagras y los 8 tornillos (4 de las bisagras y 4 de la puerta exterior). Levante la puerta interior con un desatornillador de punta plana.
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 39
    Instrucciones de instalación INVERSIÓN DE LA PUERTA B INVERSIÓN DE LA PUERTA MODELOS CON PANEL DE CRISTAL 1 Abra la puerta aproximadamente 130 grados. Con una espátula, retire las 4 tapas de plástico ubicadas a lo largo del lado izquierdo del panel frontal y deje las mismas a un costado. Tapa de pl
  • Hotpoint HTX26EASWWW | Installation Instructions - Page 40
    Instrucciones de instalación INVERSIÓN DE LA PUERTA (cont.) B INVERSIÓN DE LA PUERTA MODELOS CON PANEL DE CRISTAL (cont.) 6 Quite y cambie las 2 tapas de plástico y la bisagras de la puerta exterior. Instale las tapas de plástico de un lado opuesto aquí Instalar bisagras de lado opuesto aquí
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
- Risk of Fire
• Clothes dryer installation must be performed by a
qualified installer.
• Install the clothes dryer according to these instructions
and local codes.
•
DO NOT
install a clothes dryer with flexible plastic venting
materials. If flexible metal (semi-rigid or foil-type) duct is
installed, it must be UL-listed and installed in accordance
with the instructions found in “Connecting the Dryer
to House Vent” later in this manual. Flexible venting
materials are known to collapse, be easily crushed and
trap lint. These conditions will obstruct dryer airflow and
increase the risk of fire.
•
DO NOT
install or store this appliance in any location
where it could be exposed to water or weather.
• To reduce the risk of severe injury or death, follow all
installation instructions.
• Save these instructions. (Installers: Be sure to leave
these instructions with the customer.)
In the Commonwealth of Massachusetts,
the following installation instructions apply:
• Installation must be performed by a qualified or
licensed contractor, plumber, or gasfitter qualified
or licensed by the State.
• If using a ball valve, it shall be a T-handle type.
• A flexible gas connector, when used, must not
exceed 4 feet.
FOR GAS DRYERS ONLY
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT
–
Save these instructions for local electrical
inspector’s use.
IMPORTANT
–
Observe all governing codes and
ordinances.
• Install the clothes dryer according to the manufacturer’s
instructions and local codes.
• Note to Installer –
Be sure to leave these instructions
with the Consumer.
• Note to Consumer –
Keep these instructions for future
reference.
• Clothes dryer installation must be performed by a qualified
installer.
• This dryer
must
be exhausted to the outdoors.
• Before the old dryer is removed from service or discarded,
remove the dryer door.
• Do not allow children on or in the appliance. Close
supervision of children is necessary when the appliance
is used near children.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• Install the dryer where the temperature is above 50°F for
satisfactory operation of the dryer control system.
• Remove and discard existing plastic or metal foil duct
and replace with UL-listed duct.
• Service information and the wiring diagram are located
in the control console.
Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com
Dryers
Installation Instructions
WARNING
Failure to follow safety warnings exactly could
result in serious injury, death, or property damage.
-
DO NOT store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
-
WHAT TO DO IF YOU SMELL GAS:
•
DO NOT try to light any appliance.
•
DO NOT touch any electrical switch; DO NOT
use any phone in your building.
•
Clear the room, building, or area of any occupants.
•
Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
•
If you cannot reach your gas supplier, call the
fire department.
-
Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier.
-
Fire or Explosion
Hazard
WARNING
31-3000293
Rev 2
07-23 GEA