Hotpoint HTX26GASWWW Quick Specs

HTX26GASWWW

Hotpoint® 6.2 Cu. Ft. Capacity Gas Dryer with up to 120 Ft. Venting and Shallow Depth

DRYER DIMENSIONS (IN INCHES)

Specification Revised 2/24

EXHAUST OPTIONS:

3-way via rear, left and bottom. Dryer is shipped

exhausted to the rear. Alternate exhausting knockouts are supplied.

CIRCUIT REQUIREMENTS:

An individual properly-grounded branch

circuit, with a three-prong grounding-type receptacle, protected by

a 15- or 20-amp circuit breaker or a time-delay fuse, is required.

GAS DRYER ELECTRIC RATING:

120V, 60Hz, 6 Amp

GAS (BTU/HR):

22,000. Factory-equipped for natural gas.

Tested for LP gas. LP gas supply requires an optional conversion

kit. Check installation instructions for correct kit and have a qualified

gas technician install a conversion kit. See dryer ducting information

for proper installation.

INSTALLATION INFORMATION:

For complete information, see

installation instructions packed with product for current dimensional data.

SPECIAL INSTALLATION REQUIREMENTS

ALCOVE OR CLOSET INSTALLATION:

- If your dryer is approved for installation in an alcove or closet, it will be

stated on a label on the dryer back.

- The dryer MUST be exhausted to the outside.

- Minimum clearances between dryer cabinet and adjacent walls or other

surfaces are: 0" either side, 1" front, top and rear

- Closet doors must be louvered or otherwise ventilated and must contain

a minimum of 60 sq. in. of open area equally distributed. If this closet

contains both a washer and a dryer, doors must contain a minimum of

120 sq. in. of open area equally distributed.

- No other fuel-burning appliance shall be installed in the same closet with

a gas dryer.

BATHROOM OR BEDROOM INSTALLATION:

- The dryer MUST be exhausted to the outdoors.

- The installation must conform with the local codes, or in the absence of local codes,

with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:

Minimum clearances to combustible surfaces 0" both sides, 1" rear.

22 3/8"

26 5/8"

3 7/8"

5"

37 1/2"

44"

SIDE VIEW

1 7/8"

3 1/8"

44"

27"

4 7/8"

POWER CORD 4 3/4"

11 3/4"

REAR VIEW

*Order online at GEApplianceparts.com, 24 hours a day or by phone at 877.959.8688 during normal business hours.

For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions, visit our website

at geappliances.com or call GE Answer Center® Service, 800.626.2000.

POWER CORDS:

GE Appliances strongly recommends

the use of factory specified parts. Select the power cord

to fit your installaton requirements.*

NOTE:

If the dryer circuit is on a circuit protected by a

GFCI breaker, then 3-wire installation is not permitted.

Hose wiring and dryer must be configured for 4-wire.

Part Number

WX9X2

WX9X3

WX9X4

WX9X18

WX9X19

WX9X20

Type

3-Prong

3-Prong

3-Prong

4-Prong

4-Prong

4-Prong

Length

4 Feet

5 Feet

6 Feet

4 Feet

5 Feet

6 Feet

Amperage

30

30

30

30

30

30

Listed by

Underwriters

Laboratories

Hotpoint HTX26GASWWW Quick Specs

Hotpoint HTX26GASWWW Manual

Hotpoint HTX26GASWWW manual content summary: