Hotpoint RGB528PENBB Owners Manual - Page 39

Install The Anti-tip Device, Cont.

Get Hotpoint RGB528PENBB - 30 Inch Gas Range PDF manuals and user guides View all Hotpoint RGB528PENBB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Installation instructions [] iNSTALL THE ANTI-TIP DEVICE (cont.) [] For wood construction, drill a pilot hole at an angle of 20 ° from the horizontal. A nail or awl may be used if a drill is not available. Mount the Anti-Tip device with the screw provided. For cement or concrete construction, you will need a 1/4" x 11/2" lag bolt and a 1/2" O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware. Wallboard Back of range screw WHEN ALL HOOKUPS ARE COMPLETED Make sure all controls are left in the OFF position. Make sure the flow of combustion and ventilation air to the range is unobstructed. CONVERT TO LP GAS (or convert back to natural gas from LP} This range leaves the factory set for use with natural gas. if you want to convert to LP gas, the conversion must be performed by a qualified LP gas installer. The conversion instructions and LP orifices can be found attached to the range next to the pressure regulator. Keep these instructions and the orifices in case you want to convert back to natural gas. Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended hardware. for the [] Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Installation
instructions
[]
[]
iNSTALL THE ANTI-TIP DEVICE
(cont.)
For wood
construction,
drill
a pilot
hole
at an angle
of
20 ° from
the
horizontal.
A nail
or awl
may
be used
if a drill
is not
available.
Mount
the
Anti-Tip
device
with
the
screw
provided.
For
cement
or concrete
construction,
you
will
need
a 1/4" x
11/2
" lag
bolt
and
a 1/2"
O.D.
sleeve
anchor,
which
are
not
provided.
Drill
the
recommended
size
hole
for
the
hardware.
Wallboard
Back of
range
screw
[]
Install
the
sleeve
anchor
into
the
drilled
hole
and
then
install
the
lag
bolt
through
the
device.
The
bolts
must
be properly
tightened
as recommended
for
the
hardware.
Slide
the
range
against
the
wall,
and
check
for
proper
installation
by
grasping
the
front
edge
of the
cooktop
and
carefully
attempting
to tilt
the
range
forward.
WHEN ALL
HOOKUPS
ARE
COMPLETED
Make
sure
all
controls
are
left
in
the
OFF
position.
Make
sure
the
flow
of
combustion
and
ventilation
air
to
the
range
is
unobstructed.
CONVERT TO
LP GAS
(or
convert
back
to
natural gas
from
LP}
This
range
leaves
the
factory
set
for
use
with
natural
gas.
if
you
want
to
convert
to
LP gas,
the
conversion
must
be
performed
by
a qualified
LP gas installer.
The
conversion
instructions
and
LP orifices
can
be found
attached
to
the
range
next
to
the
pressure
regulator.
Keep
these
instructions
and
the
orifices
in
case
you
want
to
convert
back
to
natural
gas.
39