Humax IR-PLUS User Manual
Humax IR-PLUS Manual
 |
View all Humax IR-PLUS manuals
Add to My Manuals
Save this manual to your list of manuals |
Humax IR-PLUS manual content summary:
- Humax IR-PLUS | User Manual - Page 1
IR-PLUS RoHS/Manual/IRPLUS/100GBFAAR *20007-1560PT* 20000-5760 - Humax IR-PLUS | User Manual - Page 2
** Thank you for purchasing a HUMAX Digital Satellite Receiver. Please read this user manual carefully, to be able to safely install, use and maintain the product at maximum performance. Keep this user manual next to your product for future reference. Throughout the whole manual, Note mark indicates - Humax IR-PLUS | User Manual - Page 3
that there is adequate ventilation and that you have followed the manufacturer's instructions for mounting. Do not place the product on an unstable cart, openings in the unit, where they can touch dangerous voltage points or damage parts. • When replacement parts are required, be sure the service - Humax IR-PLUS | User Manual - Page 4
Contents 1.2 Front Panel 1.3 Rear Panel 1.4 Conditional Access 1.5 Remote Controller 2. Setup 2.1 Connecting Antenna/TV 2.2 Connecting Hi-Fi System 2.3 Powering On 3. Installation 3.1 Selecting Language 3.2 Searching Services 3.3 Default Setting 4. Basic Operation 4.1 Viewing Programme 4.2 Changing - Humax IR-PLUS | User Manual - Page 5
Switching Services 5.2 Organising Services 5.3 Organising Favourite Services 5.4 Organising Satellites 6. Programme Guide 7. Setting Preferences 7.1 Parental Control 7.2 System Setting 8. System Information 9. Utility 10. Software Update 11. Troubleshooting 12. Specification 13. Service and Support - Humax IR-PLUS | User Manual - Page 6
you have all the necessary items shown in figure below. If any of items is missing or damaged, please contact your product dealer for replacement. ** ** Remote Controller ** ** ** Batteries User's Manual ** Note: The product image may differ from the actual product. RCA Cable ** GB 5 - Humax IR-PLUS | User Manual - Page 7
** 1.2 Front Panel ** ** Note: The front panel of the product may differ according to the product type. GB 6 - Humax IR-PLUS | User Manual - Page 8
Button ** Switches between Operation and Standby modes. ** 5. VOL Button ** Display the volume bar. ** 6. CH-/CH+ or VOL-/VOL+ ** Moves the TV/Radio service or volume up/down. ** 7. SMART CARD SLOT ** Slot for a smart card. ** ** Note: See 1.4 Conditional Access when you insert the smartcard. GB 7 - Humax IR-PLUS | User Manual - Page 9
Rear Panel ** ** 1. LNB IN ** Connects a satellite antenna cable. ** 2. LNB OUT ** Connect other digital satellite receiver. ** 3. RS-232C ** Connects to your PC to update product's software programme. ** 4. AUDIO L/R ** Connects to your TV or VCR and output Audio signals. ** 5. VIDEO ** Connects - Humax IR-PLUS | User Manual - Page 10
A Smartcard looks similar to a credit card and entitles you to view and listen to all the services you choose to subscribe to. The Smartcard slot on the product can be used for Irdeto Smartcard only. ** 1. Open the right-hand flap on the front panel of the product. 2. Hold the Smartcard horizontally - Humax IR-PLUS | User Manual - Page 11
** 1.5 Remote Controller GB 10 1. SOURCE ** Selects the input source between TV and product. ** 2. TV/RADIO ** Switches between TV and Radio modes. ** 3. NUMERICAL BUTTONS ** Enters a TV/Radio service number. ** 4. MENU ** Displays the main menu. ** 5. TIME - WHITE ** Displays the current time on - Humax IR-PLUS | User Manual - Page 12
** Displays the Programme Guide. ** 15. EXIT ** Returns to the previous menu and exits all OSD screens. ** 16. OK ** Selects a menu or confirms the selection. Displays the service list during watching a programme. 17. ZOOM - BLUE ** Enlarges the picture. ** 18. SUBTITLE - YELLOW ** Display the - Humax IR-PLUS | User Manual - Page 13
case. Before you connect the product to any other equipment, you must disconnect all the equipment from their power sources. Note: If you encounter any problem when setting up the product, please contact your local product distributor. 2.1 Connecting Antenna/TV ** ** 1. Connect an Antenna to LNB - Humax IR-PLUS | User Manual - Page 14
** 2.2 Connecting Hi-Fi System ** ** 1. Connect an Antenna to LNB IN on the product. 2. Connect VIDEO on the product to VIDEO IN on the TV using the RCA cable. 3. Connect AUDIO L/R on the product to AUDIO IN L/R on the Audio System using the RCA cable. GB 13 - Humax IR-PLUS | User Manual - Page 15
** 2.3 Powering On ** 1. Connect the power cord of the product to a wall outlet. ** ** 2. Press the STANDBY button on the front of the product or on the remote controller. ** GB 14 - Humax IR-PLUS | User Manual - Page 16
HUMAX Auto Search. For information about it, refer to 3.2 Searching Services. 3.2 Searching Services To search services, go to Service Searching menu (MENU-INSTALLATION-SERVICE 6. Press the button to open the option list and press the services may differ depending on the type of the receiver. - Humax IR-PLUS | User Manual - Page 17
Auto Search If your product is connected to the antenna and television, you can automatically search services without entering any other information. Warning: Please note that once you perform HUMAX Auto Search, all data such as Antenna setting information channel lists and smart card information - Humax IR-PLUS | User Manual - Page 18
can set antenna and LNB information to search services. ** • Antenna Alternative: Select antenna alternative which by name. If the desired satellite name is not listed, then select User Defined. You can enter the Satellite Name using the keyboard displayed on the move to the Manual Search menu. GB 17 - Humax IR-PLUS | User Manual - Page 19
** 3. Manual Search You can search services of the selected satellite by transponders if you know the again. The screen also shows the information of the number of the found services and transponder. To save the found services, press the OK button. ** Note: • If the antenna is correctly set - Humax IR-PLUS | User Manual - Page 20
the desired satellite name is not listed, then select OTHER. • Movement: In user mode, this is used to fine-tune the position of the motor. In installer the satellite manually. • Motor Control: You can select one option among Search, Goto, Store, or Reset. ** - Search: Searches for services on the - Humax IR-PLUS | User Manual - Page 21
, press the OK button. To set the motor position for each satellite manually, select your desired Satellite Name, set DiSEqC Command Mode to Installer, and satellite, select your desired Satellite Name, set DiSEqC Command Mode to User, set Motor Control to Goto, and set Movement to your desired - Humax IR-PLUS | User Manual - Page 22
press the MENU button, then select INSTALLATION-SERVICE SEARCHING-MANUAL SEARCH-AUTOMATIC SEARCH. ** • Antenna press the OK button to start service search. ** Note: The menu structure may vary according to the type of the receiver. ** 3.3 Default Setting You settings except customised password. GB 21 - Humax IR-PLUS | User Manual - Page 23
using the CH-/CH+, , or NUMERICAL button. You can also use the Service List or Programme Guide. You can adjust the audio volume using the V-/V+ or button. ** Programme Information (i-plate) ** i-plate which is also called Information Box is always displayed for a specific - Humax IR-PLUS | User Manual - Page 24
SETTING-LANGUAGE SETTING-MENU LANGUAGE. 4.3. Teletext When the service supports teletext, the teletext icon is displayed on the I-plate button and press Sub-page Search the sub-page using the sub-code written by users. If it's not in the teletext mode, display the current time updating it. GB 23 - Humax IR-PLUS | User Manual - Page 25
setting may vary according to the type of the receiver. • In case of unlocking a service, you will be prompted to enter your Pin Code. The default Pin Code is "1234". • When switching to the locked service, you should enter the Pin Code to view the service. • You will not be allowed to watch the - Humax IR-PLUS | User Manual - Page 26
2. Press the COLOUR button to display the corresponding service list. RED (All service list), GREEN (Favourite service list), YELLOW (Bouquet service list), BLUE (Satellite service list), WHITE (Alphabet service list) 3. Select your desired service using the , CH-/CH+ or NUMERICAL button, and - Humax IR-PLUS | User Manual - Page 27
button. You can lock, unlock, move, skip, and delete services. You can rename a service. You can select a service using the button, and press the COLOUR button to execute the button. ** Note: You should enter your Pin Code using the NUMERICAL button to watch the locked services. GB 26 - Humax IR-PLUS | User Manual - Page 28
like to save the changes, select OK, and press the OK button. The Organise Favourite TV/Radio Services screen consists of Favourite Group and Favourite List on the left side of the screen and Service List on the right side. You can move the highlighter in order of Favourite Group, Favourite List - Humax IR-PLUS | User Manual - Page 29
** 5.4 Organising Satellites You can turn a satellite on or off and delete a transponder. To enter Organise Satellites menu, go to MENU-INSTALLATION-SERVICE ORGANISING-ORGANISE SATELLITES. The Organise Satellites screen consists of Satellite List on the left side of the screen and Transponder - Humax IR-PLUS | User Manual - Page 30
your desired programme and to watch or reserve it. You can go to the programme guide screen by using MENU-TV GUIDE. To close the guide screen, press the GUIDE or EXIT button. ** You can navigate the guide using the following instructions: • Press the RED button to display the current or next - Humax IR-PLUS | User Manual - Page 31
TV/RADIO button to switch to the Radio Guide. • The reservation icons on the reserved programmes in the guide differ according to the reservation type. Once appropriately. If the service is locked, restricted by watching time, you will be prompted to enter your PIN Code to complete the reservation - Humax IR-PLUS | User Manual - Page 32
your Pin Code, please contact your local product distributor. 7.2 System Setting The System Setting menu (MENU-INSTALLATION-SYSTEM SETTING) lets you set language, time, audio/video output, UHF tuning, transparency of OSD, duration time of i-plate, switching mode to reserved service, and selecting - Humax IR-PLUS | User Manual - Page 33
. 5. Other Setting You can adjust the transparency level of On-Screen Display (OSD), set the duration time of the i-plate displayed when switching services and select automatic or manual mode to change to the reserved service. Note: This menu may vary according to the type of the receiver. GB 32 - Humax IR-PLUS | User Manual - Page 34
signal strength and signal quality of the service that is currently being viewed. 4. Conditional Access You can check the information of Conditional Access component - CA Module and Smartcard. 5. Mail Messages You receive mails sent by broadcasting company. When a new mail arrives, the envelope - Humax IR-PLUS | User Manual - Page 35
your biorhythm, and enjoying games. To use utilities, go to MENU-UTILITY. If you are not familiar with navigating menu, see 3.2 Searching Services. ** 1. Calendar You can see the specified monthly screen. button. Use the , OK, COLOUR, or EXIT button according to the instructions displayed GB 34 - Humax IR-PLUS | User Manual - Page 36
not so good that the quality of receiving signal strength is not recommendable, perform the software upgrade later. ** Caution: • Please be careful to keep the power on and the power cord plugged in during software update. If the power is off during software update, it may cause fatal damage to the - Humax IR-PLUS | User Manual - Page 37
** The product cannot work at all during software update. It may take 5-10 minutes to update software. Updating software is largely divided into two ways, automatic detection and using software update menu (MENU-INSTALLATION-STATUS-STB UPGRADE). New software can be found when powering on the product - Humax IR-PLUS | User Manual - Page 38
** Before contacting your local service, please read the following instructions. If the product does not work normally after completing the following troubleshooting, please contact your local product distributor or service centre. ** 1. The LED on the front panel does not light. - Check the main - Humax IR-PLUS | User Manual - Page 39
should directly point towards its receiving part of the product. - Check the battery of the remote controller. ** 6. Reservation is unavailable - Check whether it is not overlapped with other reservation. - Check whether the power is off. ** 7. Watching scrambled service is not available - Check the - Humax IR-PLUS | User Manual - Page 40
** MPEG Transport Stream A/V Decoding Aspect Ratio Video Resolution Audio Mode 4:3, 16:9 720 x 576, 720 x 480 Single /Dual mono/ Stereo /Joint stereo Memory Flash Memory Graphics(MPEG) & System Memory EEPROM 2 Mbytes 8 Mbytes 8 Kbytes RF-Modulator Output Channel TV standard Preset Channel - Humax IR-PLUS | User Manual - Page 41
such as troubleshooting guide, software upgrades and product support guide from the following web sites and call centre (Hotline). Please try to contact to your local dealers first when you have any problem. ** Homepage http://www.humaxdigital.com http://www.humaxdigital.com/Deutsch/ English