Humax PVR-9100 User Manual
Humax PVR-9100 Manual
 |
View all Humax PVR-9100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Humax PVR-9100 manual content summary:
- Humax PVR-9100 | User Manual - Page 1
in this document is subject to change without notice. HUMAX does not have any responsibility for direct, indirect, HUMAX personal video recorder. Please read this user manual carefully, to be able to safely install, use and maintain the receiver at maximum performance. Keep this user manual - Humax PVR-9100 | User Manual - Page 2
back). No user serviceable parts inside. Refer servicing to qualified service personnel. ** This symbol indicates dangerous voltage inside the receiver that ** presents a risk of electric shock or personal injury. This symbol indicates important instructions accompanying the receiver. ** GB - Humax PVR-9100 | User Manual - Page 3
carefully. ** Safety Instructions and Precautions ** 1. MAINS SUPPLY ** 90 - 250V AC 50/60Hz Operate this receiver only from the type the receiver. ** 7. CONNECTION TO THE SATELLITE DISH LNB ** Disconnect the receiver from the mains before connecting or disconnecting the cable from the satellite - Humax PVR-9100 | User Manual - Page 4
's instructions for mounting. Do not place the receiver on an unstable cart, stand, tripod, bracket, or table where it can fall. A falling receiver can PARTS ** When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that - Humax PVR-9100 | User Manual - Page 5
of data on the hard disk drive caused by the carelessness or misuse of users. 6. Lock and Unlock switch Fix the Lock and Unlock switch to the Unlock switch. ** ** This receiver provides up to 80GB of hard disk drive. The company shall not be liable for problems caused by the installation of hard - Humax PVR-9100 | User Manual - Page 6
** ** Contents ** 1. Before Using the Receiver 1.1 Package Contents 1.2 Front Panel 1.3 Rear Panel 1.4 Remote Controllor GB9 ** GB9 GB10 GB13 GB14 2. Basic Operation GB26 ** ** 4.1 Switching Channel GB26 4.2 Volume Control GB26 4.3 Change the Subtitle Language GB26 4.4 Change a Audio - Humax PVR-9100 | User Manual - Page 7
Programmes 6.5 MP3 6.6 Digital Album 6.7 Checking Hard Guide GB54 ** ** 8.1 Viewing Programme Guide Information GB54 ** 8.2 Finding a Programme GB56 8.3 Viewing Reserved Programme GB57 9. Setting Preferences 9.1 Parental Control 9.2 Language Setting 9.3 Time Setting 9.4 A/V Control - Humax PVR-9100 | User Manual - Page 8
.1 OTA (Over the Air) 11.2 Software Update from PC GB86 ** GB86 GB90 12. System Information 12.1 Status 12.2 Signal Detection 12.3 Common Interface GB91 ** GB91 GB91 GB91 13. Games GB92 ** 14. Menu Map GB93 ** 15. Troubleshooting 15.1 Troubleshooting GB94 ** GB94 15.2 Error Message GB96 - Humax PVR-9100 | User Manual - Page 9
** ** ** ** ** 1.Before Using the Receiver ** This chapter provides detailed instructions on the receiver and its accessories. 1.1 Package Contents Please check all package contents before using your receiver. ** ** ** Remote Controller User's Manual Tuner Loop-through Cable ** ** ** - Humax PVR-9100 | User Manual - Page 10
up/down. 4. HDD LED ** Blink when your receiver is reading or writing HDD. 5. PLAY LED ** PVR. Unlock when you separate a hard disk drive from your PVR. Note: For a right operation, refer to the Warning part. 8. USB Slave Port ** Connect to the PC port. (For moving the information of digital - Humax PVR-9100 | User Manual - Page 11
** ** ** ** Mounting or Separating of the Hard Disk Drive 1. Separating the hard disk drive 1. Open the right-hand flap on the front panel of the receiver. 2. Please fix the Lock and Unlock switch to the Unlock. 3. Press the OK button in the display screen. 4. Pull the HDD cartridge. The - Humax PVR-9100 | User Manual - Page 12
. 3. Please fix the Lock and Unlock switch to the Lock. 4. Press the OK ** button in the display screen and be rebooted your receiver automatically. ** ** ** Warning: Do not pull or push by compulsion when you treat the hard disk drive. Please use caution when removing the HDD cartridge - Humax PVR-9100 | User Manual - Page 13
antenna cable. Up to two cables can be connected. ** 2. LNB OUT ** Connect other digital satellite receiver. ** 3. RS-232C ** Connects to your PC to update receiver's software programme. 4. TV SCART ** ** Connects a TV SCART cable. ** 5. VCR SCART ** Connects a VCR SCART cable. 6. VIDEO - Humax PVR-9100 | User Manual - Page 14
** ** ** ** ** 1. Before Using the Receiver ** 1.4 Remote controller ** ** ** ** Note: The remote controller could be different according to the area. ** GB 14 ** ** ** ** ** ** ** - Humax PVR-9100 | User Manual - Page 15
** Selects the input source between TV ** Displays the channel list. and satellite receiver. ** ** 11. MENU 2. TV / RADIO ** Switches between TV and Selects a menu, or confirms the selected 20. GUIDE ** Displays the Programme Guide. operation. And displays the channel list during watching - Humax PVR-9100 | User Manual - Page 16
** ** ** ** ** 1. Before Using the Receiver ** 22. PLAYBACK CONTROL BUTTONS (FAST REWIND) 23. PIP and TSR BUTTONS (TIME BAR) ** Rewinds a programme. Each time you press this button, the scenes is rewound more faster divided - Humax PVR-9100 | User Manual - Page 17
. Select the most appropriate procedure depending on your requirements. Note: If you encounter any problem when setting up your receiver, please contact your local receiver distributor. 2.1 Connecting TV, VCR and Hi-Fi system. 1. Connecting to the TV only This is the most simple set-up mode - Humax PVR-9100 | User Manual - Page 18
** ** ** ** ** 2. Setup ** 2. Connection to the TV with VCR Connect one end of the SCART cable to the TV and VCR SCART socket on the receiver and the other end to a SCART socket on the TV and VCR. ** ** ** ** GB 18 ** ** ** ** ** ** ** - Humax PVR-9100 | User Manual - Page 19
. Connect the outputs on this receiver to corresponding inputs on your Hi-Fi system. (left audio out to left audio in, right audio out to right audio in) If you wish to connect the optical S/PDIF terminal and Dolby digital decoder to listen digital audio, connect as following. ** ** ** ** GB - Humax PVR-9100 | User Manual - Page 20
to the Antenna. We recommend one of the following antenna connections. PVR-9100 has two antenna modes according to setting: Single and Dual. ** Loop Through Connect the antenna cable to your receiver, and connect the other cable to another receiver as a loop through. The Connection Type in - Humax PVR-9100 | User Manual - Page 21
be set to Dual cable(Same). ** ** ** ** 3. Two separated antennas setting Connect the two antenna cables providing different broadcasting signals to your receiver. You can configure LNB1, and LNB2 independently. The Connection Type in Installation should be set to Dual cable(Diff). ** ** GB 21 - Humax PVR-9100 | User Manual - Page 22
1. Connect the power cord of the receiver to a wall outlet. ** 2. Turn on the power button, located at the left on the back of the receiver. Make sure that Standby LED is turned on Blue. ** ** ** ** 3. Power on by pressing the STANDBY button at Remote Controller or the STANDBY button at the - Humax PVR-9100 | User Manual - Page 23
** ** ** ** ** 3. Installation Wizard ** When powering on your receiver for the first time after purchasing, the Installation Wizard is automatically started. You can easily set-up using simple organisation and options, and watch the - Humax PVR-9100 | User Manual - Page 24
screen, are generally moved up. • If you encounter any problems or questions when setting up the antenna, please contact your local receiver installer or distributor. 3.4 Automatic Search You can automatically search for satellites according to the Antenna Setting. Please wait for finishing the - Humax PVR-9100 | User Manual - Page 25
, you may not watch any broadcasting normally. In this case, you can use the Menu-Installation-Antenna Setting and Channel Search menu to configure your receiver as you like. ** GB 25 ** ** ** ** ** ** ** - Humax PVR-9100 | User Manual - Page 26
between TV channel and Radio channel. Note: You can switch channel using the channel list or programme guide. Please refer to Chapter 7 and 8 for more information. 4.2 Volume Control 1. Press the V-/V+ 2. Press the MUTE buttons to adjust the audio volume. button to stop the sound temporarily - Humax PVR-9100 | User Manual - Page 27
list. button to Note: • You can select your desired default audio language by selecting MENU - Preferences - Language Setting - Audio Language. • If the programme is Dolby digital one, you cannot set the audio direction such as left, right, and stereo. • If you select Dolby - Humax PVR-9100 | User Manual - Page 28
. Displayed only when the programme is a dolby digital one. ** 4. Current time 5. Detailed programme information: displayed if detailed programme information is provided. 6. Signal strength and signal quality: indicates signal level. 7. Satellite name or channel change mode: If you select - Humax PVR-9100 | User Manual - Page 29
** ** ** ** ** ** ** 2. Detailed Programme Information You can see detailed information about the current programme. Press the i button where I-plate is displayed to view detailed information. Note: • Press the i button again to hide the information box. • If the detailed programme - Humax PVR-9100 | User Manual - Page 30
** ** ** ** ** 4. Basic Operation ** 2. Lock/Unlock a Channel You can lock or unlock the current channel while watching a programme. 1. Press the OPT+ button. 2. Select Lock using the or button. button, and press the OK 3. Select Lock option using the OK button. button, and press the - Humax PVR-9100 | User Manual - Page 31
on the Information. 1st Line Provider name 2nd Line Satellite and CAS type 3rd Line Transponder Information for the channel Line Video PID, Audio PID, PCR PID(Packet Identification) ** 5th Line Service ID(SID), Network ID(NID) ** Note: The display information could be changeable - Humax PVR-9100 | User Manual - Page 32
you watch a scrambled TV programme. 1. Swapping the PIP screen. This function is available either 1:6 PIP or 1:1 PIP. Press the SWAP PIP button on the remote controller to swap the main screen for the PIP screen. Press the CH-/CH+ or button to change the main screen channel. You can change - Humax PVR-9100 | User Manual - Page 33
** 3. Changing a PIP channel in the PIP screen. You can select and change the PIP channel using the * button. Press the PIP button on the remote controller to display the PIP screen, then press the * button. The PIP channel lists display in the main screen. Press the CH-/CH+ or button to - Humax PVR-9100 | User Manual - Page 34
Shifted Recording (TSR) Your PVR automatically saves the programme on air in the installed hard disk drive temporarily, so that users can watch programmes as Time 2. Pause If you press the PLAY/PAUSE button on the remote controller, the current programme is paused. If you press the PLAY/PAUSE - Humax PVR-9100 | User Manual - Page 35
programme is automatically played at normal speed from the point. 4. Fast Forward to the Next Scene Press the FORWARD button on the remote controller to fast forward the programme. Whenever you press the FORWARD button, the speed increases by 4 steps. ( x 2, x 4, x 16, x 24) ** If you press - Humax PVR-9100 | User Manual - Page 36
and Time Shifted Recording ** 6. Additional Time Shift Operations You can perform additional time shift operations using the following buttons on the remote controller. ** Slow Motion Press the SLOW MOTION button to play the current programme in slow motion mode. Whenever you press the SLOW - Humax PVR-9100 | User Manual - Page 37
you will press the A-B button during repeating the selected block. You can perform the time shift operations like VCR functions using the Playback control buttons while playing a programme. Press the STOP button to stop playing the current saved programme, and watch the current programme on air - Humax PVR-9100 | User Manual - Page 38
receiver has a hard disk drive inside, you can record a programme without an external media device such as a VCR. ** ** 6.1 Instant Recording Press the RECORD button on the remote controller Schedule and Guide - Schedule. For detailed information on recording reservation using Guide, refer to - Humax PVR-9100 | User Manual - Page 39
the existing one, adjust the reservation so as not to overlap. ** • If the target channel is locked, restricted by watching time or parental control, you have to enter a password for reservation. 2. Editing Recording Reservations 1. Select a reserved programme list and press the OK button to add - Humax PVR-9100 | User Manual - Page 40
shift operations like VCR functions such as rewind, forward, slow motion, pause, skip, and replay using the playback control or the additional buttons on the remote controller while you are playing back a programme. Note: For more information on the time shift operations like VCR functions, refer - Humax PVR-9100 | User Manual - Page 41
** ** ** ** ** ** ** 6.4 Editing Recorded Programmes Select Menu - Record - Recorded Programme, and then select the desired recorded programme to edit the information of the programme. 1. Press the MENU button. 2. Select Record using the or button. button, and press the OK 3. Select - Humax PVR-9100 | User Manual - Page 42
MP3 list in the Menu - Record - MP3. ** This menu is going to support in the near future. According to the condition, the menu structure will be changed forward, stop, play and pause using the additional buttons on the remote controller while you are playing back a MP3. Note: For more information - Humax PVR-9100 | User Manual - Page 43
Album You can listen or edit the MP3 list in the Menu - Record - Digital Album. This menu is going to support in the near future. According to the condition, the menu structure will be changed. 1. Press the MENU button. 2. Select Record using the or button. button, - Humax PVR-9100 | User Manual - Page 44
can format the disk drive if necessary. 1. Press the MENU button. 2. Select Record using the or button. button, and press the OK 3. Select HDD Control using the OK or button. button, and press the 4. You can check the free, used, reserved, and total space of the HDD. 5. Select Format and - Humax PVR-9100 | User Manual - Page 45
name. The list of the favourite channels with 5 subgroups that you can organise channels by your private taste. The lists of channels classified by satellites. The number of subgroup is decided by the result of channel search. The lists of channels classified by CAS types. The number of subgroup is - Humax PVR-9100 | User Manual - Page 46
subgroup is displayed. ** ** Note: • The subgroup of favourite channel list may exist or not depending on your configuration. And the subgroup of Satellite and Scramble channel list may exist or not depending on the result of Channel Search. • If Within the Current Channel List option is - Humax PVR-9100 | User Manual - Page 47
numeric for each menu. Press the MENU - 3 - 1 in order at remote controller to select Edit Channel List menu. • If the Connection Type is Dual, to edit. TV or Radio, and the subgroups from the channel search for satellite and scramble channel lists are included as channel list groups. 1. Press the - Humax PVR-9100 | User Manual - Page 48
** ** ** ** ** 7. Channel List ** 2. Delete Channels You can delete one or more channels. 1. Move the cursor to the channel list using the button. 2. Select your desired channel, and then press the OK button. You can select multiple channels. 3. Select Delete in the right using the button - Humax PVR-9100 | User Manual - Page 49
** ** ** ** ** ** ** 4. Move the cursor to the desired location in the channel list using the the OK button. 5. The selected channel(s) is moved to the selected location in order. button, and press Note: Move is available only for TV or radio channel list. The channel number is changed - Humax PVR-9100 | User Manual - Page 50
screen. • You can easily navigate all menu items using the assigned NUMERICAL (0~9) button for each menu. Press the MENU - 3 - 2 in order on the remote controller to select the Edit Favourite Channels menu. ** The buttons for editing the Favourite channel list are described in the following table - Humax PVR-9100 | User Manual - Page 51
channel list, and press to remove Favourite channels. Note: You can switch between TV and Radio channel list using the TV/RADIO remote controller or . button at 2. Move favourite channels You can move favourite channel to your desired location within the Favourite channel list. This function - Humax PVR-9100 | User Manual - Page 52
channel list. Press to switch TV or Radio channels. Note: You can also change into TV or Radio channel by pressing the TV/RADIO remote controller. ** Select a favourite channel list button at You can select your desired Favourite channel list to edit. Press to display the Favourite channel list - Humax PVR-9100 | User Manual - Page 53
** ** ** ** ** ** ** 7.5 Channel Change Mode You can change the channel either in the group or in the entire channels while watching a programme. 1. Press the MENU button. 2. Select Channel Change Mode using the and press the OK or button. button, 3. Select All Channels or Within the - Humax PVR-9100 | User Manual - Page 54
can enter your desired channel number using the NUMERICAL (0-9) button at remote controller to move to the channel directly. 4. Select your desired programme, Information for the ** selected programme. ** 1. Viewing Guide Information by Channel List Groups You can view programme information - Humax PVR-9100 | User Manual - Page 55
quickly search for your desired time zone using the Time bar. 1. Press the GUIDE button. 2. Press the GREEN button to display Time Bar. 3. Select the again to cancel reservation. 2. If the channel is locked, parental controlled or restricted by watching time, you will be prompted to enter your - Humax PVR-9100 | User Manual - Page 56
** 8.2 Finding a Programme You can find your desired programme by programme name or genre easily. 1. Press the GUIDE button. 2. Press the BLUE button to display Find screen. 3. Enter the programme name directly using the keyboard displayed on the screen. 4. When completing entering programme - Humax PVR-9100 | User Manual - Page 57
Programme You can add or edit watching-reserved programme by schedule screen. 1. Press the GUIDE button. 2. Press the YELLOW button to display the Schedule screen. 3. Select the reserved : Lock mode is displayed only for the receiver with hard disk drive. ** GB 57 ** ** ** ** ** ** ** - Humax PVR-9100 | User Manual - Page 58
** ** ** ** ** 8. Programme Guide ** 2. Adding a Reservation 1. Select a blank list and press the OK new your Password to complete the ** reservation. ** Note: • Lock mode is displayed only for the receiver with hard disk drive. • You can reserve up to 20 programmes. • If your desired - Humax PVR-9100 | User Manual - Page 59
exit the Menu screen. • You can easily select all menu items using the assigned numerical button for each menu. 9.1 Parental Control You can set parental control for each programme and watching time. You can also change your Password. 1. Press the MENU button. 2. Select the Preferences using - Humax PVR-9100 | User Manual - Page 60
time for all the channels. 1. Select the Allow Time Control using the button. 2. Select Enable or Disable the Allow Time Control using the OK or button. ** Disable You can watch have forgotten your Password, please contact your local receiver distributor. ** GB 60 ** ** ** ** ** ** ** - Humax PVR-9100 | User Manual - Page 61
the selected language. Dolby Digital You can listen sound in Dolby Digital mode. However, if you select Dolby Digital, you cannot change the language. Manual Subtitles are displayed in the language when you select the subtitle language by pressing the SUBTITLE button at remote controller. ** - Humax PVR-9100 | User Manual - Page 62
** ** ** ** ** 9. Setting Preferences ** 4. Subtitle Font You can select the Subtitle font. 1. Select Subtitle Font using the button. 2. Select your desired option using the OK or button. ** Variable Uses the horizontally variable Subtitle Font. Fixed Uses the fixed Subtitle Font. - Humax PVR-9100 | User Manual - Page 63
Channel No and Time using the NUMERICAL (0~9) buttons, and select OK and press the OK button. 4. Power Off You can set the time when the receiver is automatically powered off. 1. Select Power Off using the button. 2. Select either Enable or Disable the Power Off using the OK or button - Humax PVR-9100 | User Manual - Page 64
. 1. Press the MENU button. 2. Select Preferences using the OK or button. button, and press the 3. Select AV Control using the OK or button. button, and press the 1. TV-SCART You can set TV SCART Output. 1. Select TV-SCART using the button, and press - Humax PVR-9100 | User Manual - Page 65
, and press the OK or button. ** 2. Select one option among Auto/PAL/NTSC using the button. ** Auto The TV supports both PAL and NTSC. PAL The TV supports only PAL. NTSC The TV supports only NTSC. button, and press the OK 7. NTSC Mode If TV Standard is set to NTSC, set the following - Humax PVR-9100 | User Manual - Page 66
** ** ** ** ** 9. Setting Preferences ** 9.5 UHF Tuning You can set the UHF Tuning channel. 1. Press the MENU button. 2. Select Preferences using the OK or button. 3. Select UHF Tuning using the OK or button. button, and press the button, and press the 1. UHF Channel You can - Humax PVR-9100 | User Manual - Page 67
** ** ** ** ** ** ** 9.6 Miscellaneous Settings 1. Press the MENU button. 2. Select Preferences using the OK or button. button, and press the 3. Select Miscellaneous Settings using the and press the OK or button. button, 1. i-Plate Display Time You can set the duration during - Humax PVR-9100 | User Manual - Page 68
** ** ** ** ** 9. Setting Preferences ** 4. Instant replay time You can watch the current programme from the 7 seconds before. 1. Select the Instant replay time using the button, and press the OK 2. Select one option among 7/15/30 using the button, and press the OK or button. button. - Humax PVR-9100 | User Manual - Page 69
) using the button, and press the OK button. Refer to the Chapter 2.2. Single cable Connect the antenna cable to your receiver, and connect the other cable to another receiver as a loop through. Dual cable(Same) Connect both of the antenna cables providing the same broadcasting signal to your - Humax PVR-9100 | User Manual - Page 70
button, and press ** the OK or button to enter Antenna Setting. Note: If no satellite is registered from Antenna Setting menu, Channel Search such as Automatic Search, Manual Search, Multiple Manual Search, Advanced Search is not available. ** 1. Antenna Setting of the fixed antenna You can - Humax PVR-9100 | User Manual - Page 71
When you are prompted to select whether or not to edit User Define Satellite, select Yes, and press the OK to display keyboard to edit the Name. Enter Satellite Name directly, select OK, and press the OK button. ** Satellite Alternative You can search and watch a programme by using the antenna - Humax PVR-9100 | User Manual - Page 72
Swtich using the button, and press the OK button. You can select one option among Disable, DiSEqC A~D, DiSEqC A~D for 2.0 and Tone burst A,B. ** LNB Voltage This receiver doesn't provide this function. ** ** ** GB 72 ** ** ** ** ** ** ** - Humax PVR-9100 | User Manual - Page 73
enter LNB Frequency value using the NUMERICAL (0~9) button after selecting User Define. When completing entering LNB Frequency, press the OK button Installaion - Antenna Setting - LNB Voltage. The distance between antenna and receiver is 30m instead of 60m. 3. Select Motor Kind using the Type. - Humax PVR-9100 | User Manual - Page 74
unavailable. 4. Select Satellite Longitude using the press the OK button. button, and 5. Enter the Longitude value for Satellite using the NUMERICAL (0~9) button. Change East/West value using the button. Note: Satellite Longitude item is able to edit only for User Define Satellite. ** GB 74 - Humax PVR-9100 | User Manual - Page 75
. Continuous Step Time Motor moves continuously Motor moves by specified unit. Motor moves during specified time. 4. Move the Antenna to the position of the selected Satellite. ** Select Go to Stored Position using the button. Press the OK button to move Antenna to the position ** of the - Humax PVR-9100 | User Manual - Page 76
** ** ** ** ** 10. Installation ** Installer Menu You can set default setting and operation limit for Motor Antenna. Select Installer Menu from Motor Antenna Menu using the to move to Installer Menu. button. Press the OK 1. Set Motor Limit. You can set the maximum Motor Limit both East - Humax PVR-9100 | User Manual - Page 77
OK button. ** ** Note: Channel Search is performed only for the satellites that have been set to Enable in Antenna Setting-Satellite Alternative menu. If you wish to search channels for satellites, which is not listed on the Satellite List of Automatic Search, move to Antenna Setting and set - Humax PVR-9100 | User Manual - Page 78
** ** ** ** ** 10. Installation ** 3. Channel Type You can search by TV or Radio channel. 1. Select Channel Type using the button, and press the OK or button. 2. Select one option from among All, TV and Radio using the button. All TV Radio Searches all channels. Searches only TV - Humax PVR-9100 | User Manual - Page 79
the OK or button. button, and press the 3. Select Manual Search from Installation menu using the button, and press the OK or button. 1. Satellite Selects a satellite to search from the satellites set in Antenna setting. 1. Select Satellite using the button, and press the OK or button - Humax PVR-9100 | User Manual - Page 80
information, select Done and press the OK button to finish entering User Define Transponder value. Note: • For channel transponder information, you can find your desired information from Satellite channel magazine, Satellite channel related home pages, news release and home page of broadcasting - Humax PVR-9100 | User Manual - Page 81
channel. Searches only Radio Channel. 6. Search You can complete the setting and start searching. 1. Select Search and press the OK button to start Manual Search. 2. The next procedures are the same as those of Automatic Search. Please refer to Automatic Search. 10.5 Other Search ** You can - Humax PVR-9100 | User Manual - Page 82
Advanced Search using the button to start Advanced Search. ** Satellite, Transponder button, and press the OK or The setting for satellite and transponder is the same as that of Manual Search. Refer to the satellite and transponder setting for Manual Search. ** Video PID, Audio PID, PCR PID You - Humax PVR-9100 | User Manual - Page 83
** ** ** ** 2. SMATV Search If your receiver uses the antenna for common use, operate SMATV Search. the symbol rate of the transponder. If the rate does not exist in the list, select User Define and enter the value directly. ** FEC ** 1. Select FEC using the button, and press the OK - Humax PVR-9100 | User Manual - Page 84
Search from Other Search Menu using the button, press the OK or button to enable the Multiple Manual Search. Note: Settings for Satellite, Search Type, and Channel Type is the same as those of Manual Search. Refer to Automatic Search. ** Edit Transponder List You can edit TP list to search at - Humax PVR-9100 | User Manual - Page 85
** ** ** ** ** 10.6 Default Setting Default Setting restores the receiver to the default settings Warning: Please note that once you perform Default Setting, all data such as Antenna Setting information Channel List, and User Configured data are deleted. But the recorded programme of the HDD - Humax PVR-9100 | User Manual - Page 86
Humax website - http://www.humaxdigital.com. It is recommended that you periodically check for the availability of software update. 11.1 OTA (Over the Air) OTA, an abbreviation of Over-the-Air, means that downloads the software can be downloaded be received). The software update via satellite - Humax PVR-9100 | User Manual - Page 87
using the button, and press the OK ** or button. ** 3. Automatic Update You can set the receiver to find HUMAX software update site and update software automatically. 1. Select Automatic Update from Update screen using the button, and press the OK or button. Automatically search for new - Humax PVR-9100 | User Manual - Page 88
** 11. Software Update ** Note: Software Update Sites of HUMAX are listed in the following table. ** Satellite Transponder data Astra1 12669 (V) 22000 5/6 Nilesat 11765 (H) 27500 3/4 Hotbird 12475 (H) 27500 3/4 ** Among the Software Update Sites of HUMAX, the software search operation - Humax PVR-9100 | User Manual - Page 89
. 5. Select FEC value. Note: How to setting Satellite and Transponder for Manual Update Sites is the same as how to edit User Define Transponder data in Manual ** Search. Refer to Manual Search. ** 6. Select Search and press the OK software. button to search 7. It is displayed whether or - Humax PVR-9100 | User Manual - Page 90
** ** ** ** 11. Software Update ** 11.2 Software Update from PC You can connect your receiver to the PC directly and update your software by transferring the new software from the PC. Follow these steps to download new software from PC to this receiver. 1. Download new software file(HDF files - Humax PVR-9100 | User Manual - Page 91
2. Confirm the information about Hardware version, Software version, Loader version, System ID, Update Date and Slot 1, 2. ** 12.2 Signal Detection You can view the signal strength and signal quality receiving from satellite via your satellite dish. 1. Select Signal Detection using the button - Humax PVR-9100 | User Manual - Page 92
** ** ** ** ** 13. Games ** This receiver provides various games for user's entertainment. 1. Press the GAME button. 2. According to the instruction displayed on screen, you can enjoy the game using the and OK button. Note: Press the EXIT or BACK button to exit the game. ** ** ** - Humax PVR-9100 | User Manual - Page 93
** ** ** ** ** 14. Menu Map ** ** ** ** GB 93 ** ** ** ** ** ** ** - Humax PVR-9100 | User Manual - Page 94
** ** 15. Trouble Shooting ** 15.1 Trouble Shooting Before contacting your local service, please make sure following instructions. If the receiver does not work normally after completing the following trouble shooting, please contact your local receiver distributor or service centre. ** 1. No - Humax PVR-9100 | User Manual - Page 95
** ** 5. Remote controller does not operate. ** - To control the equipment with the remote controller, the remote controller's top end should directly point towards the receiving part of receiver's remote controller. - Check the battery of Remote controller. - Check the battery of Remote controller - Humax PVR-9100 | User Manual - Page 96
** ** ** ** 15. Trouble Shooting ** 15.2 Error Message Error message Possible causes What to do No or bad signal The satellite dish is not pointing at the satellite. Adjust dish. Signal to weak. Increase the LNB voltage or connect a signal amplifier. Satellite dish is too small. Change - Humax PVR-9100 | User Manual - Page 97
Install other CI module to check if the exiting CI module has problem. If the existing CI has no problem, contact local distributor of the equipment. Invalid CI module CI model and substance or damaged. contact local service center if it is ** damaged. ** ** GB 97 ** ** ** ** ** ** - Humax PVR-9100 | User Manual - Page 98
+18V (+18.5V at high voltage) Current: 500mA Max. Overload Protection 22kHz Tone Frequency: 22 ± 4kHz Amplitude: 0.6 ± 0.2V DiSEqC Control Version 1.0/1.2/2.0 Compatible, USALS Demodulation QPSK Input Symbol Rate 1 ~ 45 Ms/s FEC mode Convolutional Code Rate 1/2, 2/3, 3/4, 5/6 and 7/8with - Humax PVR-9100 | User Manual - Page 99
75 , IEC169-2 470 ~ 862 MHz CH 21~69 PAL B/G/I/D/K RCA/SCART Video Output (CVBS, RGB, S-video) RCA/SCART Volume and Mute Control (Resolution: 20 bits DAC, MAX. 2Vrms) Digital Audio Output, Fiber-Optic (Resolution: 20 bits) Transfer Rate: 115,200 bps, 3 pin Socket type 90 ~ 250V AC, 50/60Hz SMPS - Humax PVR-9100 | User Manual - Page 100
(Digital Satellite Equipment Control) A standard through which it is possible to let a DiSEqC compatible receiver send a signal over the RF cable to a switching device to switch between different LNBs or dishes. The DiSEqC uses the 22KHz signal to control the switching device. ** Programme Guide - Humax PVR-9100 | User Manual - Page 101
** ** ** ** ** ** ** OTA (Over The Air) Means that software downloads where the manufacturer reserves the right to decide when and where to release them through satellite system. ** PID (Packet Identifier) A set of numbers that identifies the transport streams packets that containing data - Humax PVR-9100 | User Manual - Page 102
** ** ** ** 18. Service and Support ** You can get information such as a troubleshooting guide, software upgrades and receiver support guide from the following web sites and call center (Hotline). Please try to contact to your local dealers first when you have any problem. Web site and e-mail - Humax PVR-9100 | User Manual - Page 103
Call Charge) Open: Local Time in Germany (GMT+1) 8:00 - 20:00 (Monday - Friday) 8:00 - 18:00 (Saturday) Support Language: Deutsch/English ** ** ** Humax BTCI Hotline (Premiere Model) Germany: 01805-778900 ( 0,12/Min) Austria: 0900-900633 ( 0,33/Min) ** For hardware repair, please refer to