Hunter 20182 Owner's Manual
Hunter 20182 Manual
 |
View all Hunter 20182 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hunter 20182 manual content summary:
- Hunter 20182 | Owner's Manual - Page 1
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name Model No. Date Purchased Where Purchased Type 2 Models Owner's Guide and Installation Manual English Español Form# 42626-01 20110505 ©2011 Hunter Fan Co. - Hunter 20182 | Owner's Manual - Page 2
Cleaning Your Ceiling Fan 15 9 • Troubleshooting 16 Cautions and Warnings • READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION. SAVE THESE INSTRUCTIONS. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of - Hunter 20182 | Owner's Manual - Page 3
an approved connector. • Six inches of lead wires extend from outlet box. If your existing fan site is suitable, skip ahead to Section 2 • Installing the Ceiling Plate. Fan Support System Fan Support System Suitable Existing Fan Site Wiring Outlet Box 3 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 4
go to your fan manual and continue with Section 2 • Installing the Ceiling Plate. Step 5 CAUTION: All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. 4 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 5
close to the ceiling, recommended for ceilings less than 8 feet high CAUTION: To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions, and use only the hardware supplied. 5 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 6
To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct - Hunter 20182 | Owner's Manual - Page 7
the service panel. 2-1. Drill two pilot holes into the wood support structure Ceiling Peak For Angled Ceilings: Be sure to orient the ceiling plate so that the two tabs are pointing toward the ceiling peak. Ceiling Plate 3" Wood Screw Steps 2-3 - 2-6 7 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 8
profile screws. Hanging the Fan: Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. 3-7. Raise the fan and align the slots in Adapter Low Profile Screw Low Profile Washer 8 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 9
them carefully back through the ceiling plate into the outlet box. 4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 9 42626-01 • 05/05/11 • Hunter Fan Company Wire Connector Dual Switch Wiring Single - Hunter 20182 | Owner's Manual - Page 10
up with the screw holes aligned, partially install two canopy screws into the holes opposite the ceiling plate tabs. 5-4. Partially install a canopy screw between the slots in the canopy. When all 5-2 Step 5-3 Canopy Canopy Trim Ring Canopy Screw 10 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 11
, and attach lightly to the fan. Insert the second blade mounting screw, then securely tighten both mounting screws. Step 6-1 (Detail) Grommet Steps 6-1 - 6-2 Use with grommet Blade Assembly Screws Step 6-4 Use without grommet 11 42626-01 • 05/05/11 • Hunter Fan Company Blade Mounting Screw - Hunter 20182 | Owner's Manual - Page 12
not you are installing a light fixture. WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the upper switch housing, partially install two housing assembly screws into the - 7-3 Housing Assembly Screw Upper Switch Housing 12 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 13
sticker affixed to the light socket(s) may result in fire hazard or improper operation. If lights do not appear to be operating properly, see the troubleshooting section. Steps 7-8 - 7-10 13 42626-01 • 05/05/11 • Hunter Fan Company Shade Bulb - Hunter 20182 | Owner's Manual - Page 14
The light switch remains in the light assembly housing.) 7-17. Insert the pull chain and fan pull chain switch through the Steps 7-17 - 7-21 round opening on the side of capacitors in the switch housing. Fan Speed Switch 7-21. Continue with Step 7-6. 14 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 15
chain has two settings: On and Off. 8-4. Ceiling fans work best by blowing air downward (counterclockwise blade fan off and let it come to a complete stop. Slide the reversing switch on the fan to the opposite position. Restart fan. Reversing Switch 15 42626-01 • 05/05/11 • Hunter Fan Company - Hunter 20182 | Owner's Manual - Page 16
blade is cracked. If so, replace all the blades. Problem: Excessive wobbling. 1. If your fan wobbles when operating, use the enclosed balancing kit and instructions to balance the fan. 2. Tighten all blade iron screws. 3. Turn power off, support fan very carefully, and check that the hanger ball is
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Type 2 Models
Type 2 Models
Type 2 Models
Form# 42626-01
20110505
©2011 Hunter Fan Co.
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
English
Español
Owner’s Guide and Installation Manual