Hunter 21620 Owner's Manual
Hunter 21620 Manual
 |
View all Hunter 21620 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hunter 21620 manual content summary:
- Hunter 21620 | Owner's Manual - Page 1
For Your Records and Warranty Assistance Model Name Catalog/Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a copy of your receipt to the manual. installation and operation manual for Hunter Ceiling Fans TYPE 3 Models 42700-01 • 01/15/08 - Hunter 21620 | Owner's Manual - Page 2
and Cleaning Your Ceiling Fan 15 12 • Troubleshooting 16 Welcome Your new Hunter® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your - Hunter 21620 | Owner's Manual - Page 3
, including a wall-mounted or remote speed control. To install and use the accessories, follow the instructions included with each product. For quiet and optimum performance of your Hunter fan, use only Hunter speed controls. Support Brace Ceiling Outlet Box For ceilings higher than 8 feet, you - Hunter 21620 | Owner's Manual - Page 4
. If any parts are missing or damaged, contact your Hunter dealer or call Hunter Technical Support Department at 888-830-1326. Preparing the Fan Site Before you begin installing the fan, follow all the instructions in the pullout sheet called "Preparing the Fan Site." Proper ceiling fan location and - Hunter 21620 | Owner's Manual - Page 5
over tighten. Isolator Ceiling Plate Flat Washer Step 2-2 Steps 2-3 - 2-5 3 in. Wood Screw For Angled Ceilings: Be sure to orient the ceiling plate so that the hook and one of the threaded screw holes in the ceiling plate are on the lower side. 5 42700-01 • 01/15/08 • Hunter Fan Company - Hunter 21620 | Owner's Manual - Page 6
with the holes in the fan motor. 3-2. Slide flat washers onto the shafts of the blade assembly screws. 3-3. Attach the blade to the motor using the blade assembly screws. 3-4. Repeat for each blade. Step 3-1 Blade Assembly Screw Step 3-2 Flat Washer 6 42700-01 • 01/15/08 • Hunter Fan Company - Hunter 21620 | Owner's Manual - Page 7
on the hanger adapter with the three narrow notches in the top housing. Make certain the housing sits flat on the adapter. 4-2. Install three (3) assembly screws and tighten them securely. Steps 4-1 - 4-2 Assembly Screw Top Housing Hanger Adapter 7 42700-01 • 01/15/08 • Hunter Fan Company - Hunter 21620 | Owner's Manual - Page 8
sure the green ground wire is pointing up toward the ceiling. 5-5. Align the fan and place the hook on the ceiling plate through the round hole in the rim. WARNING: Fan may fall if not assembled as directed in these installation instructions. Round Hole 8 42700-01 • 01/15/08 • Hunter Fan - Hunter 21620 | Owner's Manual - Page 9
remote receiver and transmitter. If they don't match, the transmitter will not function. 6-2. Install the included 12-volt battery into the transmitter. CAUTION: The remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company - Hunter 21620 | Owner's Manual - Page 10
red wire from the fan to the red wire from the receiver. • Connect the black wire with a white stripe from the fan to the black wire with a white stripe from the receiver. • Connect the white wire from the fan to the white wire (LIGHT OUT) from the receiver. 10 42700-01 • 01/15/08 • Hunter Fan - Hunter 21620 | Owner's Manual - Page 11
the ceiling plate and the downrod to the ground wire from the ceiling. 7-9. Push all wires and wire connectors back through the ceiling plate hole into the outlet box. Place the green and white wires on a separate side of the outlet box from the other wires. 11 42700-01 • 01/15/08 • Hunter Fan - Hunter 21620 | Owner's Manual - Page 12
8-1- 8-3 8 • Installing the Canopy 8-1. Holding the canopy, raise the fan off the hook. 8-2. Align the holes in the canopy with the mounting holes on the ceiling plate. 8-3. Insert and tighten the mounting screws securely. Canopy Mounting Screw 12 42700-01 • 01/15/08 • Hunter Fan Company - Hunter 21620 | Owner's Manual - Page 13
globe into the globe trim band. Align the three holes in the trim band with the three holes in the fitter. Install and securely tighten all three screws. Steps 9-1 - 9-8 Light Kit Fitter Fluorescent Bulb Globe Trim Band Step 9-9 Ballast Glass Globe 13 42700-01 • 01/15/08 • Hunter Fan Company - Hunter 21620 | Owner's Manual - Page 14
mount the remote holder on the wall. 10-7.This product includes one 12-volt type 23A, MN-21 battery for use with the remote control transmitter. Please contact your local battery recycling center for proper battery disposal information. Step 10-6 14 42700-01 • 01/15/08 • Hunter Fan Company - Hunter 21620 | Owner's Manual - Page 15
remote control will not be used for 5 days or more, turn the wall switch OFF. 11-3. Ceiling fans the fan draw air upward (clockwise blade rotation) will distribute the warmer air trapped at the ceiling around -gloss blades in the same manner as the fan finish. In warm weather, use downward air flow - Hunter 21620 | Owner's Manual - Page 16
/or blade iron screws. 3. Turn power off, support fan very carefully, and check that the hanger ball is properly seated. If you need parts or service assistance, please call 888‑830‑1326 or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: ________________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
TYPE 3 Models
installation and
operation manual
for Hunter
Ceiling Fans
42700-01 • 01/15/08