Hunter 82043 Owner's Manual
Hunter 82043 Manual
 |
View all Hunter 82043 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hunter 82043 manual content summary:
- Hunter 82043 | Owner's Manual - Page 1
Installation Guide ENGLISH See page 2 Español Vea la página 19 Energy Star Bath Fan Models 82043 READ and SAVE THESE INSTRUCTIONS 1 43045-01 10/15/2009 - Hunter 82043 | Owner's Manual - Page 2
manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. SAVE THESE INSTRUCTIONS. 2) Before installing, servicing Figure A. NOTE: This illustration is not to scale Bath Fan 3 ft. min. (0.91 m) Tub or Shower area 7 ft. min. (2.13 m) - Hunter 82043 | Owner's Manual - Page 3
) Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the unit , do not use this fan with any solid-state speed control device. 17) To prevent a possible fire, do not block air intakes or exhaust in any manner. 18) - Hunter 82043 | Owner's Manual - Page 4
967993322--0011--020602 P 87258-01-000 Q 87259-01-000 Wiring Cover Wiring Cover Screw Strain Relief Bracket Strain Relief Bracket Screw Fan Assembly Fan Mounting Screws Light Fixture Light Bulbs Lens Included. Before Installation A Tools Needed. (Not supplied.) Estimated assembly time: 30 to 60 - Hunter 82043 | Owner's Manual - Page 5
C D Remove the fan assembly from the housing. E Loosen the wiring cover screw. Remove the wiring cover. Choose Installation Option For New Construction - attaching to joist, go to step - Hunter 82043 | Owner's Manual - Page 6
Section A - New Construction - attaching to joist A1 OR Pop out a wiring access slug. A2 A3 5/8 5/8 1/2 1/2 Position the correct depth mark at the bottom edge of the joist based upon the the thickness of your sheetrock. Drive mounting screws (supplied) into joist or framing. A4 A5 3" Run - Hunter 82043 | Owner's Manual - Page 7
A6 Vaya a la sección E - Instalación Final en la página 14. Connect 6" duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely, an adapter may need to be purchased. Section B - New Construction - suspended between joists B1 OR Pop out a wiring access slug. - Hunter 82043 | Owner's Manual - Page 8
B4 B5 1/16" bit Mark position of screws by using holes as a template. Drill a pilot hole at the TOP of each outline. B6 B7 Insert mounting screws, leaving space between the screw head and the joist. (Screws are supplied.) Attach the rails onto the screws. B8 B9 3" Tighten screws. Run - Hunter 82043 | Owner's Manual - Page 9
Instalación Final en la página 14. Section C - Existing Construction - accessible from above C1 NO EXISTING FAN 11" ⁄" 9 OR Remove an existing fan and check to make sure the opening is large enough to accommodate the new fan housing. The opening needs to be 11" x 9 5/8". 9 43045-01 10/15/2009 - Hunter 82043 | Owner's Manual - Page 10
C2 OR Pop out a wiring access slug. C3 C4 Slide the mounting rails into brackets. C5 5/8 5/8 1/2 1/2 Using the depth markings on the housing, position the bottom edge of the housing so that it will be flush with the sheetrock. C6 Mark position of screws by using holes as a template. Drill - Hunter 82043 | Owner's Manual - Page 11
C7 C8 Insert mounting screws, leaving space between the screw head and the joist. (Screws are supplied.) Attach the rails onto the screws. C9 C10 3" Tighten screws. C11 Run the power supply wire through the strain relief, leaving 3" between the end of the wire and the strain relief. Tighten - Hunter 82043 | Owner's Manual - Page 12
access slugs on the top of the housing. Use a second wiring access plug if needed. Remove the mounting rail brackets. D3 EXISTING FAN D4 3" Remove an existing fan and check to make sure the opening Run the power supply wire through the strain relief, leaving 3" is large enough to accommodate - Hunter 82043 | Owner's Manual - Page 13
D5 D6 Install the wiring and the strain relief into the wiring access hole you made earlier. Connect 6" duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely, an adapter may need to be purchased. D7 D8 Move the housing into the ceiling. D9 5/8 5/8 - Hunter 82043 | Owner's Manual - Page 14
housing mounted to a joist, the final installation procedure is the same whether the housing is mounted to a joist or suspended between joists. E3 E4 Connect fan wiring harness. DO NOT ALLOW THE FAN TO HANG FROM THE WIRING HARNESS. INSTALLATION IS EASIER IF TWO PEOPLE ARE INVOLVED. Install the - Hunter 82043 | Owner's Manual - Page 15
E5 E6 Secure the fan assembly by tightening the two fan mounting screws. E7 E8 Remove thumbnuts. Remove light bulb cover. E6 Plug in wiring harness. E7 Install the strain relief bracket. DO NOT ALLOW THE - Hunter 82043 | Owner's Manual - Page 16
E11 E12 Secure the fan assembly by tightening the two fan mounting thumbnuts. E12 E13 Install light bulbs. Install night light. E15 Install light bulb cover. E9 Complete. 16 43045-01 10/15/2009 Restore power at the source. - Hunter 82043 | Owner's Manual - Page 17
Preventative Maintenance A clean fan provides better service. Disconnect the power supply and clean the fan as listed below. TO CLEAN THE or unusual noises, contact Hunter Technical Support (see Troubleshooting section) to order a new fan assembly. Trouble Shooting Problem: Fan does not come on. - Hunter 82043 | Owner's Manual - Page 18
FIXTURES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION . To obtain servicing, contact Hunter Fan Company Technical Support at 1-888-830-1326. Please contact us before shipping your Bath Fan to us. If
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
43045-01
10/15/2009
1
I
n
s
t
a
l
l
a
t
i
o
n
G
u
i
d
e
Energy Star Bath Fan Models 82043
READ and SAVE THESE INSTRUCTIONS
ENGLISH
See page 2
ESPAÑOL
Vea la página 19