Husqvarna 327P5x Owners Manual

Husqvarna 327P5x Manual

Get Husqvarna 327P5x PDF manuals and user guides View all Husqvarna 327P5x manuals
Add to My Manuals
Save this manual to your list of manuals

Husqvarna 327P5x manual content summary:

  • Husqvarna 327P5x | Owners Manual - Page 1
    Operator's manual (EPA) 327P4 327P5X-series Please read the operator's manual carefully and make sure you understand the instructions before using the machine. English
  • Husqvarna 327P5x | Owners Manual - Page 2
    read the operator's manual carefully and make sure you understand the instructions before using the machine before you start work. This machine has a long reach. Make sure that no people or animals come closer a visor must be worn. Filling with chain oil and adjusting oil flow Always wear approved
  • Husqvarna 327P5x | Owners Manual - Page 3
    head 15 Fitting the bar and chain 15 Adjusting the harness 15 Filling with oil 16 Assembling and dismantling the two-piece shaft . 16 Fitting the impact guard 16 Assembly of the saw attachment use of nonauthorized accessories or replacement parts. WARNING! A pole saw is a dangerous ! tool if
  • Husqvarna 327P5x | Owners Manual - Page 4
    harnessed from the Huskvarna River to create the waterpowered plant. During over 300 years of continuous operation, the Husqvarna chain saws in 1959, and it is within this area Husqvarna is working today. Today Husqvarna ′s manual as a valuable document. By following its′ content (using, service,
  • Husqvarna 327P5x | Owners Manual - Page 5
    14 Protective guard for saw chain 15 Bar nut 16 Chain tensioning screw 17 Chain 18 Bar 19 Chain oil tank 20 Filling with chain oil 21 Operator's manual 22 Transport guard, bar 23 Allen key 24 Combination spanner 25 Harness (327P4) 26 Balance Flex harness (327P5) 27 Shaft coupling (327P5) 28 Upper
  • Husqvarna 327P5x | Owners Manual - Page 6
    service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading poisoning. IMPORTANT! A pole saw is a dangerous tool if with a spring- cutting attachments. loaded stop switch and
  • Husqvarna 327P5x | Owners Manual - Page 7
    section. If your machine fails any of these checks contact your service agent to get it repaired. Throttle lockout The throttle lockout that the return springs work properly. See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger
  • Husqvarna 327P5x | Owners Manual - Page 8
    flers it is very important that you follow the instructions on checking, maintaining and servicing your machine. Never use a machine that has a The risk increases at low temperatures. Regularly check that the muffler is securely attached to the machine. If the muffler on your machine is fitted with
  • Husqvarna 327P5x | Owners Manual - Page 9
    Follow our instructions and use the recommended raker gauge. Too large a clearance increases the risk of kickback. • Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket. Check that the harness straps
  • Husqvarna 327P5x | Owners Manual - Page 10
    and saw chain When the cutting attachment supplied with your machine has to be replaced, because it is worn out or damaged, you must only fit the types of bar and saw chain recommended by us. Bar • Length (inches/cm) Chain • Saw chain pitch (inches). (The distance between three drive links, divided
  • Husqvarna 327P5x | Owners Manual - Page 11
    kickback considerably: File angle too large Cutting angle too small - File depth File diameter too small 1 5 It is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file Sharpening cutting teeth To sharpen cutting teeth you will need a round
  • Husqvarna 327P5x | Owners Manual - Page 12
    saw over and file the remaining teeth from the other side. Setting the raker clearance • File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced Place the file over the part of the lip that protrudes
  • Husqvarna 327P5x | Owners Manual - Page 13
    same time as a full fuel tank. Therefore check the amount of oil in the oil tank when filling the fuel to prevent damage to the saw chain and bar that may arise due to a lack of lubrication. - Tighten the bar nut using the combination spanner. Check that the
  • Husqvarna 327P5x | Owners Manual - Page 14
    daily. We recommend you compare the existing chain with a new chain to decide how badly the existing chain is worn. When the length of the cutting teeth has worn down to only 0.16 inch (4 mm) the chain must be replaced. WARNING! A faulty cutting attachment ! may increase the risk of accidents
  • Husqvarna 327P5x | Owners Manual - Page 15
    the screw (A) is aligned with the hole in the shaft as shown. • Tighten screw A. • Tighten screw B. B A CAUTION! Make sure that the drive shaft inside the shaft engages with the cut-out in the cutting head. Fitting the bar and chain • The chain is correctly tensioned when there is no slack on the
  • Husqvarna 327P5x | Owners Manual - Page 16
    the bar head Dismantling: Loosen the coupling by turning the knob (at least 3 times). • Fill with Husqvarna saw chain oil. • Refit the cap. Assembling and dismantling the two-piece shaft (327P5) • Push and hold the button (C). While securely holding the engine end, pull the attachment straight out
  • Husqvarna 327P5x | Owners Manual - Page 17
    tighten the knob securely. Dismantling • Loosen the coupling by turning the knob (at least 3 times). Assembly of the saw attachment (327P5) Assembly • Loosen the coupling by turning the knob. • Align the tab of the attachment (A) with the arrow on the coupling (B). B A • Push and hold the button
  • Husqvarna 327P5x | Owners Manual - Page 18
    part gas station to find out where to dispose of excess fuel. • Ensure the machine is cleaned and that a complete service is carried out before long-term storage. • The transport guard must always be fitted to the cutting attachment Mixing ratio 1:50 (2%) with HUSQVARNA two-stroke oil. Gasoline,
  • Husqvarna 327P5x | Owners Manual - Page 19
    . Always move the machine away from the refuelling area before starting. • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. • Ensure that the fuel is well mixed by shaking the container before filling the tank. English - 19
  • Husqvarna 327P5x | Owners Manual - Page 20
    the chain is adequately lubricated. See instructions under the heading Lubricating the cutting attachment. • Check that the cutting attachment always stops machine that lacks a part or has been modified outside its specifications. WARNING! The complete clutch cover ! and shaft must be fitted before
  • Husqvarna 327P5x | Owners Manual - Page 21
    and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged
  • Husqvarna 327P5x | Owners Manual - Page 22
    WORKING TECHNIQUES General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a pole saw. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage
  • Husqvarna 327P5x | Owners Manual - Page 23
    power lines it could lead to death or serious bodily injury. Safety instructions after completing work • Let the engine drop back to idle speed cutting attachment. This is extremely sharp and can easily cause cuts. • Store the machine out of reach of children. • Use only original spare parts for
  • Husqvarna 327P5x | Owners Manual - Page 24
    the branch thickness to prevent jamming. Keep the chain running while you withdraw the cutting attachment from the branch to prevent it jamming. • Cut large branches in sections so that you have better control over where they fall. • Use the harness to support the weight of the machine and make it
  • Husqvarna 327P5x | Owners Manual - Page 25
    Your Husqvarna service workshop (who will have a rev counter at their disposal) to adjust your carburettor. WARNING! The complete clutch cover ! and shaft machine according to the starting instructions and let it warm up for 10 minutes. CAUTION! If the cutting attachment rotates when the engine is
  • Husqvarna 327P5x | Owners Manual - Page 26
    speed jet H. You should therefore remove the cutting attachment, nut, support flange and drive disc before adjusting the high speed jet H. so that the cutting attachment stops, contact your dealer/service revolution counter at their disposal problems or too low a working speed. 26 - English
  • Husqvarna 327P5x | Owners Manual - Page 27
    converter the screen should be cleaned weekly, or replaced if necessary. On mufflers fitted with a cylinder and piston. See also instructions under the heading Maintenance. CAUTION! Never use a spark plug electrodes, which may result in operating problems and starting difficulties. If the machine is
  • Husqvarna 327P5x | Owners Manual - Page 28
    the spark plug is fitted with a suppressor. Two-piece shaft The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a risk that the drive shaft ends (splined coupling) on models with two-piece shafts will seize if they are not lubricated regularly. Cleaning
  • Husqvarna 327P5x | Owners Manual - Page 29
    list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual the cutting attachment does not rotate at idle. X Clean the air filter. Replace if
  • Husqvarna 327P5x | Owners Manual - Page 30
    TECHNICAL DATA Technical data 327P4 Engine Cylinder displacement, cu.in/cm3 1,50/24,5 Cylinder bore, inch/mm 1,34/34 Stroke, inch/mm 1,06/27 Recommended max. speed, rpm 11500-12500 Idle speed, rpm 2700 Max. engine output, acc. to ISO 8893, kW/ rpm 0,9/8400 Catalytic converter muffler
  • Husqvarna 327P5x | Owners Manual - Page 31
    10 3/8 12 3/8 10 3/8 12 3/8 Max. no of teeth on tip sprocket 7T 7T 7T 7T Chain Husqvarna S 36/Oregon 91 VG Husqvarna S 36/Oregon 91 VG Oregon 90SG Oregon 90SG L D _ PITCH = D 2 Approved accessories Saw attachment with shaft PA 110 Art No. 537 18 33-13 Use with 327P5 English - 31
  • Husqvarna 327P5x | Owners Manual - Page 32
    -related part on your equipment is defective, the part will be repaired or replaced by Husqvarna Forest & Garden. OWNER′S WARRANTY RESPONSIBILITIES • As the small off-road engine owner, you are responsible for performance of the required maintenance listed in your operator's manual. Husqvarna Forest
  • Husqvarna 327P5x | Owners Manual - Page 33
    STATEMENT EMISSION WARRANTY PARTS LIST 1 Carburetor and internal parts 2 Intake SERVICE Warranty services or repairs are provided through all Husqvarna Forest & Garden authorized servicing dealers. MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS Any replacement part manual. English - 33
  • Husqvarna 327P5x | Owners Manual - Page 34
  • Husqvarna 327P5x | Owners Manual - Page 35
  • Husqvarna 327P5x | Owners Manual - Page 36
    1150991-95 ´´®®zz++RR••33¶¶55EE¨¨ 2009-09-15
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
English
327P4
327P5
X-series
Oper
ator’s manual (EPA)
Please r
ead the operator’s manual carefully and make sure you understand the instructions
before using the machine.