Husqvarna 440 e-series Owners Manual - Page 20

STARTING AND STOPPING Starting and stopping WARNING! Note the following before ! starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries. Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything. Keep people and animals well away from the working area. Never wrap the starter cord around your hand. Starting The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards. (45) Cold engine 440e TrioBrake Start position, 1: Set the start/stop switch in the choke position by pulling the red control outward - upward. (46) Air purge, 2: Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled. (46) Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. (47) Pull the starter handle, 3: Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly until the engine fires. Push down the red choke control, 4: As soon as the engine fires which can be heard through a "puff" sound, push down on the red choke control. Pull the starter handle, 5: Keep on pulling the cord powerfully until the engine starts. 445e TrioBrake Start position, 1: Set the start/stop switch in the choke position by pulling the red control outward - upward. (49) Decompression valve, 2: Press the valve to reduce the pressure in the cylinder and make starting easier. Once the machine has started the valve will automatically return to its original setting. (49) Air purge, 3: Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled. (49) Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. (50) Pull the starter handle, 4: Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly until the engine fires. Push down the red choke control, 5: As soon as the engine fires which can be heard through a "puff" sound, push down on the red choke control. Pull the starter handle, 6: Keep on pulling the cord powerfully until the engine starts. Warm engine 440e TrioBrake Start position, 1: The correct choke/start throttle setting for warm starting is obtained by initially moving the choke control by pulling the red control outward - upwards. (46) Air purge, 2: Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled. (46) Push down the red choke control, 4: This inactivates the choke, which is not needed when starting a warm chain saw. However the movement of the start/stop switch will have engaged a high idle, making warm starting easier. Pull the starter handle, 5: Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. (47) 445e TrioBrake Start position, 1: The correct choke/start throttle setting for warm starting is obtained by initially moving the choke control by pulling the red control outward - upwards. (49) Decompression valve, 2: Press the valve to reduce the pressure in the cylinder and make starting easier. Once the machine has started the valve will automatically return to its original setting. (49) Air purge (3): Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled. (49) Push down the red choke control, 5: This inactivates the choke, which is not needed when starting a warm chain saw. However the movement of the start/stop switch will have engaged a high idle, making warm starting easier. Pull the starter handle, 6: Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. (50) 20 - English 1153159-95 Rev.2 2010-04-08