Husqvarna DRT900 Owners Manual

Husqvarna DRT900 Manual

Get Husqvarna DRT900 PDF manuals and user guides View all Husqvarna DRT900 manuals
Add to My Manuals
Save this manual to your list of manuals

Husqvarna DRT900 manual content summary:

  • Husqvarna DRT900 | Owners Manual - Page 1
    contenant plus de 10 % d'éthanol annulera la garantie du produit. 532 44 59-65 Operator's Manual Owner's Manual DRT900E Please read the operator's manual carefully and make sure you understand the instructions before using the machine. Lisez très attentivement et soyez certain de comprende ces
  • Husqvarna DRT900 | Owners Manual - Page 2
    in hard ground. The tines may catch in the ground and propel the tiller forward. If this occurs, let go of the handlebars and do not restrain the machine. MAINTENANCE AND STORAGE • Keep machine, attachments, and accessories in safe working condition. • Check shear pins, engine mounting bolts, and
  • Husqvarna DRT900 | Owners Manual - Page 3
    tools to service or repair this unit. Please read and retain this manual. The instructions will enable you to assemble and maintain your tiller properly. Always observe the "SAFETY RULES". CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. • Follow a regular schedule in maintaining
  • Husqvarna DRT900 | Owners Manual - Page 4
    tiller handles). OPERATOR'S POSITION Fig. 1 CONTENTS OF HARDWARE PACK (2) Handle Locks (1) Carriage Bolt 3/8-16 UNC x 1 Grade 5 (1) Center Locknut 3/8-16 UNC (1) Flat Washer 13/32 x 1 x 11 Gauge (1) Handle Lock Lever (1) Hairpin Clip (1) Pivot Bolt 3/8-16 UNC Grade 5 Extra Shear Pins
  • Husqvarna DRT900 | Owners Manual - Page 5
    • Remove packing material from handle assembly. HANDLE ASSEMBLY SHIFT ROD Fig. 2 INSTALL HANDLE (See Figs. 3, L.H. side of tiller and loosely assemble locknut (See Fig. 5). • Insert pivot bolt in front part of plate and tighten in lowest position will make it easier to remove tiller from carton.
  • Husqvarna DRT900 | Owners Manual - Page 6
    of shift rod to secure. SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICATOR Fig. 6 REMOVE TILLER FROM CRATE • Make sure shift lever indicator is in "N" position (See Fig. 6) • Tilt tiller to better suit operator. (See "TO ADJUST HANDLE HEIGHT" in the Service and Adjustments section of this manual). 6
  • Husqvarna DRT900 | Owners Manual - Page 7
    - Used to engage tines. LEVELING SHIELD - Levels tilled soil. OUTER SIDE SHIELD - Adjustable to protect small plants from being buried. RECOIL STARTER HANDLE - Used to start the engine. SHIFT LEVER - Used to shift transmission gears. SHIFT LEVER INDICATOR - Shows which gear the transmission is in
  • Husqvarna DRT900 | Owners Manual - Page 8
    to "SLOW" position. • Move shift lever indicator to "R" (reverse) position. • Hold tine control against the handle to start tiller move- ment. HARD TO SHIFT GEARS • Briefly engage tine control and release or rock tiller forward and backward until are able to shift gears. DEPTH STAKE (See Fig. 9) The
  • Husqvarna DRT900 | Owners Manual - Page 9
    transporting the tiller. Place depth stake pin in hole of depth stake to lock in position. This prevents tines from scuffing the ground. • Place shift lever indicator in "F" (forward) position for transporting. • Hold the tine control against the handle to start tiller movement. Tines will not turn
  • Husqvarna DRT900 | Owners Manual - Page 10
    avoid engine problems, the fuel season. See Storage Instructions for additional information tiller handle with other hand. Pull rope out slowly until engine reaches start of compression cycle (rope will Service and Adjustments section of this manual. NOTE: If engine does not start, see troubleshooting
  • Husqvarna DRT900 | Owners Manual - Page 11
    Second, the tiller won't be pulling itself, and you, toward the row next to it. • Soil conditions are important for proper tilling. Tines will not readily outward on the axle for increased stability. OUTER VIEW OF TIRE CLEVIS PIN 4 3 2 1 5 6 7 Fig. 14 CULTIVATING Cultivating is destroying
  • Husqvarna DRT900 | Owners Manual - Page 12
    tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller. All adjustments in the Service and Adjustments section of this manual c THROTTLE CONTROL d ENGINE eRH GEAR CASE GREASE FITTING c DEPTH STAKE PIN c IDLER BRACKET c WHEEL HUB
  • Husqvarna DRT900 | Owners Manual - Page 13
    oil_visc_chart5_e(drt) Fig. 18 low on oil. Change the oil after every 25 hours of operation or at least once a year if the tiller tiller is on level surface. • Oil will drain more freely when warm. • Use a funnel to prevent oil spill on tiller manual. AIR FILTER (See Fig. 20) Service
  • Husqvarna DRT900 | Owners Manual - Page 14
    " on page 3 of this manual. TRANSMISSION Once a season, lubricate the right hand side gear case grease fitting with 1 oz. of EP #1 Grease. CLEANING Do not clean your tiller when the engine and transmission are hot. We do not recommend using pressurized water (garden hose, etc.) to clean your
  • Husqvarna DRT900 | Owners Manual - Page 15
    pressure. If tire pressures are not equal, tiller will pull to one side. • Keep tires free of gasoline or oil which can damage rubber. TO REMOVE WHEEL (See Fig. 23) • Place blocks under transmission to keep tiller from tipping. • Remove hairpin clip and clevis pin from wheel. • Remove wheel and tire
  • Husqvarna DRT900 | Owners Manual - Page 16
    . • Place new belt in groove of transmission pulley and into engine pulley. BELT MUST BE IN GROOVE ON TOP OF IDLER PULLEY. NOTE POSITION OF BELT TO GUIDES. • Check belt adjustment as described below. • Replace belt guard. • Reposition wheel and replace clevis pin and hairpin clip. GROUND DRIVE BELT
  • Husqvarna DRT900 | Owners Manual - Page 17
    then the bolted tine and hub assemblies should be switched back to their original side so that the tine edge with the least wear will be used. NEW TINE WORN TINE tine_19 Fig. 26 SHARP EDGES TINE TINE Fig. 27 3-1/2" MAX HAIRPIN CLIP SHARP EDGES HAIRPIN CLIP SHARP EDGES SHEAR PIN Fig. 28
  • Husqvarna DRT900 | Owners Manual - Page 18
    FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS THE PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS. CLAMP SCREW CASING AND WIRE engine_art_78 THROTTLE
  • Husqvarna DRT900 | Owners Manual - Page 19
    TILLER • Clean entire tiller (See "CLEANING" in the Maintenance section of this manual). • Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual SYSTEM PARTS SUCH AS dirt in your gasoline will cause problems. • If possible,
  • Husqvarna DRT900 | Owners Manual - Page 20
    shear pin(s). Tines skip over ground 1. Drag Stake not lowered in forward rotating 1. Lower Drag Stake till mode. 2. Improper tilling mode. 2. Forward rotating tine drive should only be used for soft ground or for soil that has already been tilled. Hard to shift into gear 1. Gears not
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
English/
Only
532 44 59-65
Operator’s Manual
Owner's Manual
DRT900E
Gasoline containing up to 10% ethanol (E10) is accept-
able for use in this machine.
The use of any gasoline ex-
ceeding 10% ethanol (E10) will void the product warranty.
Vous pouvez utiliser de l’essence contenant jusqu’à
10 % d’éthanol (E10) avec cet appareil. L’utilisation
d’essence contenant plus de 10 % d’éthanol annulera
la garantie du produit.
Please read the operator's manual carefully and make sure
you understand the instructions before using the machine.
Lisez très attentivement et soyez certain de comprende ces
instructions avant d’utiliser cette machine