Husqvarna GTH27V48LS Owners Manual
Husqvarna GTH27V48LS Manual
 |
View all Husqvarna GTH27V48LS manuals
Add to My Manuals
Save this manual to your list of manuals |
Husqvarna GTH27V48LS manual content summary:
- Husqvarna GTH27V48LS | Owners Manual - Page 1
07002 GTH27V48LS Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 43 86-87 Rev. 3 - Husqvarna GTH27V48LS | Owners Manual - Page 2
of grass , leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage - Husqvarna GTH27V48LS | Owners Manual - Page 3
and replace with manufacturer's recommended parts, when necessary. • Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Adjust and service as required. • Maintain or replace safety and instruction labels, as necessary - Husqvarna GTH27V48LS | Owners Manual - Page 4
. Should you experience any problem you cannot easily remedy, please contact your nearest authorized servicecenter/ department We have competent, well-trained technicians and the proper tools to service or repair this tractor. Please read and retain this manual. The instructions will enable you to - Husqvarna GTH27V48LS | Owners Manual - Page 5
attachment lift lever to its highest position. • Release parking brake by depressing brake pedal. • Place freewheel control in disengaged position to disengage transmission (See "TO TRANSPORT" in the Operation section of this manual). • Roll tractor forward off skid. Continue with the instructions - Husqvarna GTH27V48LS | Owners Manual - Page 6
"TO CHECK BRAKE" in the Service and Adjustments section of this manual. ✓CHECKLIST BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been - Husqvarna GTH27V48LS | Owners Manual - Page 7
PARKING BRAKE MOWER HEIGHT MOWER LIFT LIGHTS ON FUEL BATTERY REVERSE FORWARD CRUISE CONTROL CLUTCH/BRAKE PEDAL 15 15 ATTACHMENT ATTACHMENT alert symbol, indicates a situation that could result in damage to the tractor and/or engine. HOT SURFACES indicates a hazard which, if not avoided - Husqvarna GTH27V48LS | Owners Manual - Page 8
LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your tractor. (B) BRAKE PEDAL - Used for braking the tractor and starting the engine. (C) PARKING BRAKE - Locks clutch/brake pedal into the brake position. (D) THROTTLE/CHOKE CONTROL - Used for starting and controlling - Husqvarna GTH27V48LS | Owners Manual - Page 9
Pull parking brake lever (C) up and hold, release pres- sure from brake pedal (B), then release parking brake lever. Pedal should remain in brake position. Make sure parking brake will hold tractor secure. C B Fig. 4 STOPPING (See Fig. 5) MOWER BLADES • To stop mower blades, place attachment clutch - Husqvarna GTH27V48LS | Owners Manual - Page 10
to help prevent scalping in most terrain conditions. NOTE: Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height (See "TO AD- JUST MOWER CUTTING HEIGHT" in this section of manual). • With mower in desired height of cut position, gauge wheels should be - Husqvarna GTH27V48LS | Owners Manual - Page 11
, push brake pedal quickly to brake position and engage parking brake. • To restart movement, slowly release parking brake and brake pedal. • Slowlydepressappropriatedrivepedaltoslowestsetting. • Make all turns slowly. TO TRANSPORT (See Figs. 3 and 12) When pushing or towing your tractor, be - Husqvarna GTH27V48LS | Owners Manual - Page 12
fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brake. • Move attachment clutch to "DISENGAGED" position. • Move throttle control to choke position. NOTE: Before starting - Husqvarna GTH27V48LS | Owners Manual - Page 13
control to half (1/2) speed. Disengage parking brake. 8. Drive tractor forward for approximately five feet then backwards for five feet. Repeat this driving procedure three times. Your transmission is now purged and now ready for normal operation. MOWING TIPS • Mower should be properly leveled for - Husqvarna GTH27V48LS | Owners Manual - Page 14
must maintain tractor as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tractor. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least - Husqvarna GTH27V48LS | Owners Manual - Page 15
presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. BLADE • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position. BLADE BOLT - Husqvarna GTH27V48LS | Owners Manual - Page 16
and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. DOCKING POSITION OIL DRAIN EXTENSION TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not - Husqvarna GTH27V48LS | Owners Manual - Page 17
for your garden hose to reach. IMPORTANT: Make certain the tractor's discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2. Make sure the attachment clutch control is in the "DISENGAGED" position, set the parking brake, and stop - Husqvarna GTH27V48LS | Owners Manual - Page 18
tight grip on lift lever when changing position of the lever. • Slide mower out from under right side of tractor. TO INSTALL MOWER (See Fig. 22-29) Ensure tractor is on level surface and engage parking brake. • Lower attachment lift lever to its lowest position. CAUTION: Lift lever is spring loaded - Husqvarna GTH27V48LS | Owners Manual - Page 19
and small retainer spring as shown. TS D D. RIGHT SIDE REAR MOWER BRACKET S. ANTI-SWAY BAR T. TRANSAXLE BRACKET Fig. 25 • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. • Repeat on opposite side - Husqvarna GTH27V48LS | Owners Manual - Page 20
with the results. PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 31) • With all tires properly inflated, park tractor on level ground or driveway. CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. • Raise mower to its highest position. • At both sides - Husqvarna GTH27V48LS | Owners Manual - Page 21
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT MOWER DRIVE BELT REMOVAL (See Fig. 34) • Park tractor on a level surface. Engage parking brake. • Lower attachment lift lever to its lowest position. • Remove mandrel covers. • Remove any dirt or grass clippings which may have accumulated - Husqvarna GTH27V48LS | Owners Manual - Page 22
SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 37) Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL 1. Remove mower (See "TO REMOVE MOWER" section in this manual parts - Husqvarna GTH27V48LS | Owners Manual - Page 23
SERVICE AND ADJUSTMENTS TO START ENGINE manual). If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES. TO ATTACH - Husqvarna GTH27V48LS | Owners Manual - Page 24
is necessary, see engne manual. TO ADJUST CARBURETOR Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment. TRANSMISSION REMOVAL/REPLACEMENT Should your - Husqvarna GTH27V48LS | Owners Manual - Page 25
tractor (See "CLEANING" in the Mainte- nance section of this manual). • Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING - Husqvarna GTH27V48LS | Owners Manual - Page 26
TROUBLESHOOTING PROBLEM Will not start CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter. 6. Dirty fuel filter. 7. Water in fuel. 8. Loose or damaged wiring. 9. Carburetor out of adjustment. 10. Engine valves out of adjustment. - Husqvarna GTH27V48LS | Owners Manual - Page 27
TROUBLESHOOTING PROBLEM CAUSE Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. CORRECTION 1. Check wiring, switches and connections. If not corrected, contact an authorized service parts manual. 11. Clogged mower - Husqvarna GTH27V48LS | Owners Manual - Page 28
) - - 532 43 86-88 Manual, Owner's (Spanish) WHEELS AND TIRES 1 2 11 3 4 7 10 6 wheel_art_1-vgt 5 9 8 KEY PART NO. NO. DESCRIPTION 1 532 05 91-92 Cap, Valve, Tire 2 532 06 51-39 Stem, Valve 3 532 18 18-39 Rim Assembly, Front 4 532 00 81-34 Tube, Front (Service Item Only) 5 532 16 10 - Husqvarna GTH27V48LS | Owners Manual - Page 29
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 SCHEMATIC SCH12 A AMMETER (OPTIONAL) BATTERY RED RED FUSE SOLENOID BLACK WHITE PTO SWITCH (DISENGAGED) S B M A1 G L A2 BLACK C RED A H WHITE D RED B E WHITE CLUTCH/BRAKE (PEDAL UP) BLACK STARTER M ELECTRIC - Husqvarna GTH27V48LS | Owners Manual - Page 30
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 ELECTRICAL T14S 90 33 22 30 2 27 1 91 99 100 8 79 21 34 24 27 42 43 41 26 40 25 28 55 16 0 60 AMPS 60 45 71 46 29 With 12V Outlet Option 141 103 59 30 - Husqvarna GTH27V48LS | Owners Manual - Page 31
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 ELECTRICAL KEY NO. 1 2 8 16 21 22 24 25 26 27 28 29 30 33 34 40 41 42 43 45 46 50 55 59 71 79 90 91 99 100 103 141 PART 12V Outlet 532 42 12-25 Kit G700/G730 ROS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm - Husqvarna GTH27V48LS | Owners Manual - Page 32
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 CHASSIS 297 208 15 204 18 3 203 206 137 5 176 214 14 130 130 130 130 191 207 - Husqvarna GTH27V48LS | Owners Manual - Page 33
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 CHASSIS KEY PART NO Screw Hex Wsh Hi-Lo 1/4 x 1/2 165 532 19 43-30 Bracket Support Tank 175 532 19 63-04 Crossmember 176 532 40 07-76 Screw 10-24 96-55 Kit Gaurd Brush NOTE: All component dimensions given in U.S. inches 1 inch = - Husqvarna GTH27V48LS | Owners Manual - Page 34
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 DRIVE 220 74 184 221 35 42 70 221 74 213 56 207 206 92 125 116 160 - Husqvarna GTH27V48LS | Owners Manual - Page 35
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 DRIVE KEY PART NO. NO. DESCRIPTION 1 ------ Transaxle, Hydro G7-BCBB-1XDC-1FCA 2 532 00 70-70 Key 1/4 x 2.5 3 532 00 75-63 Washer Thrust Axle Hardened 7 532 19 98-37 Hub Asm. Wheel 9 - Husqvarna GTH27V48LS | Owners Manual - Page 36
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 ENGINE 30!2+ª!22%34%2ª+)4 ENGINE TEX?BS CYL? 36 - Husqvarna GTH27V48LS | Owners Manual - Page 37
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 ENGINE KEY PART Line 29 532 13 71-80 Spark Arrester Kit 37 532 12 34-87 Clamp Hose 41 25.4 mm For engine service and replacement parts, call the toll free but not limited to, accessories (air cleaner, exhaust, charging - Husqvarna GTH27V48LS | Owners Manual - Page 38
TRACTOR - MODEL NO. GTH27V48LS 55 67 6 14 5 62 14 15 54 66 54 13 13 8 53 Steering-tex_LEGND2_36_r1 KEY PART NO. NO. DESCRIPTION 1 532 43 97-40 Wheel, Steering 2 532 19 59-68 Axle -37 Adapter, Wheel Steering 22 532 42 05-37 Steering Support Lower 26 532 43 97-43 Insert, Wheel Steering 28 - Husqvarna GTH27V48LS | Owners Manual - Page 39
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 SEAT ASSEMBLY 1 8 7 88 7 8 41 40 10 21 6 37 6 37 2 44 43 21 seat-tex_6.5SL_3 KEY PART NO. NO. 77 Pan, Seat 21 532 17 18-52 Bolt, Shoulder 5/16-18 3 KEY PART NO. NO. DESCRIPTION 37 873 80 05-00 Nut, Lock 5/16-18 unc - Husqvarna GTH27V48LS | Owners Manual - Page 40
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 MOWER DECK 52 33 24 17 57 19 53 47 25 34 54 18 31 30 32 20 43 45 5 23 22 4 46 16 51 56 - Husqvarna GTH27V48LS | Owners Manual - Page 41
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 MOWER DECK KEY PART NO. NO. DESCRIPTION 1 575 43 80-02 Deck w/ Decals 48" 2 16 539 11 28-99 Nut 5/16-18 Hex Flange Nyloc 17 532 19 61-04 Pulley, Idler Spec. Hub 18 574 82 71-02 Arm, Idler, Blk 19 532 17 79-68 Pulley, Idler 20 - Husqvarna GTH27V48LS | Owners Manual - Page 42
TRACTOR - MODEL NO. GTH27V48LS (96043011700), PRODUCT NO. 960 43 01-17 MOWER LIFT LIFT TEX? KEY PART NO. NO. DESCRIPTION 2 532 42 20-27 Shaft Asm., Lift 3 532 19 52-30 Lever Asm., Lift RH 7 532 41 15-55 Grip, Lever 10 - Husqvarna GTH27V48LS | Owners Manual - Page 43
43 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION TFHOISLDISAALO15NDGEDGORTETEESDLLOINPEE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than - Husqvarna GTH27V48LS | Owners Manual - Page 44
02.05.11 BAD Printed in the U.S.A.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
 |
 |
07002
GTH27V48LS
Owner's Manual
532 43 86-87
Rev. 3
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.
The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.