Husqvarna K 1260 Owners Manual

Husqvarna K 1260 Manual

Get Husqvarna K 1260 PDF manuals and user guides View all Husqvarna K 1260 manuals
Add to My Manuals
Save this manual to your list of manuals

Husqvarna K 1260 manual content summary:

  • Husqvarna K 1260 | Owners Manual - Page 1
    RIDER 970 RIDER 850 RIDER 850 Rider 850 HST Rider 970 HST Operator´s manual Please read these instructions carefully and make sure you understand them before using the machine. 101 89 36-26
  • Husqvarna K 1260 | Owners Manual - Page 2
  • Husqvarna K 1260 | Owners Manual - Page 3
    the oil 27 Lubrication 27 Checking and adjustment of throttle wire ......... 28 Replacement of fuel filter 28 Trouble shooting schedule 29 Storage 30 Winter storage 30 Service 30 Technical data 31 IMPORTANT INFORMATION Read through these instructions carefully so that you know how to
  • Husqvarna K 1260 | Owners Manual - Page 4
    the operator's manual RN Reverse Neutral Fast Slow Engine off Battery Choke Fuel Oil pressure Cutting height Backwards Forwards Ignition Use eye and hearing protection Clutch in Clutch out Parking brake Hydrostatic free wheel ! Brake Warning Soundlevel Warning! Rotating blades
  • Husqvarna K 1260 | Owners Manual - Page 5
    stop quickly. • Read all the instructions in Operator's Manual and on the machine before starting blades when you are not cutting. • Only cut in daylight or good artificial lighting. • Never use the machine when you have consumed alcohol, drugs, or certain medicines. RIDER 970 Read the instructions
  • Husqvarna K 1260 | Owners Manual - Page 6
    INSTRUCTIONS • Watch out for traffic when working close to a road, or crossing one. • Be careful when rounding a fixed object so that the blades or if you feel uncertain avoid cutting it. Do as follows: • Remove obstacles such as stones and branches etc. • Cut upwards and downwards, not sideways.
  • Husqvarna K 1260 | Owners Manual - Page 7
    SAFETY INSTRUCTIONS • Do not cut close to edges, ditches or banks. The machine can suddenly tip over if a wheel goes over the edge of a drop or a ditch, or if a bank gives way. • Do not cut wet grass. It is slippery and the tyres can loose their grip so that the machine slides. • Do not try
  • Husqvarna K 1260 | Owners Manual - Page 8
    cutting injuries. Wrap over the blades or use protective gloves when handling them. • Check the functioning of the brakes regularly. Adjust and maintain them as necessary. RIDER 850 Never smoke in the vicinity of the battery or the fuel. Never drive the machine in an enclosed space. RIDER 970
  • Husqvarna K 1260 | Owners Manual - Page 9
    controls 1. Ignition lock 2. Throttle/Choke lever 3. Adjustment of cutting height 4. Lifting lever, cutting unit 5. Speed limiter for reversing 6. Speed limiter for driving forwards 10 11 7. Brake pedal 8. Lock button for parking brake 9. Lever for adjustment of seat 10. Fuel tank cap 11. Main
  • Husqvarna K 1260 | Owners Manual - Page 10
    and Choke lever The engine speed is adjusted with the throttle control, and thereby also the rotation speed of the blades. The control is also used to activate the choke function. When the choke is used the engine receives a richer mixture of fuel and air, which simplifies cold start. Speed limiter
  • Husqvarna K 1260 | Owners Manual - Page 11
    which has rear or side ejection. The diagram shows a Rider 970 with Bioclip unit. Lift lever for cutting unit The lift lever is used to set the cutting unit in transport or cutting position. If the lever is pulled back the unit will lift up and the blades stop rotating (transport position). If the
  • Husqvarna K 1260 | Owners Manual - Page 12
    height With this lever the cutting height can be adjusted to 9 different positions (4-90 mm, 45-80 mm Bioclip). Seat, Rider 850 HST The seat has a jointed attachment on the front edge and can be tipped forward. The seat can also be adjusted lengthways. To adjust the lever under the seat it is
  • Husqvarna K 1260 | Owners Manual - Page 13
    position. Lock the setting with the knobs. Fuelling The engine should be run on at least 92 octane leaded or unleaded petrol/gasoline (not oil mixed). ! WARNING! Petrol/gasoline is highly inflammable. Observe care and fill up with fuel outdoors (see safety instructions). English - 11
  • Husqvarna K 1260 | Owners Manual - Page 14
    instructions and information on the location and function of the controls before starting (see pages 3-11). • Conduct daily maintenance before starting (see maintenance schedule on page 17). Adjust the seat to the required position. Starting the engine 1. Lift up the cutting the throttle control
  • Husqvarna K 1260 | Owners Manual - Page 15
    before trying again. 6. When the engine has started release the ignition key to neutral position. Push the throttle control to the required speed. For cutting 3/4 to full throttle. ! WARNING! Never run the engine indoors, in enclosed or poorly ventilated areas. The exhaust fumes contain toxic
  • Husqvarna K 1260 | Owners Manual - Page 16
    DRIVING Driving the machine 1. Release the parking brake by pressing down the brake pedal. 2. Carefully press down one of the pedals until the correct speed is reached. To drive forwards: press down pedal (1). To reverse: press down pedal (2). 2 1 RIDER 850 14 - English
  • Husqvarna K 1260 | Owners Manual - Page 17
    unit. IMPORTANT INFORMATION The service-life of the drive belts increases considerably if the engine is run at low speed when engaging the blades. For this reason do not increase the throttle until the cutting unit has been lowered to the cutting position. Cutting tips • Localise and mark stones
  • Husqvarna K 1260 | Owners Manual - Page 18
    to obtain normal working temperature before stopping it if it has been working hard. 1. Lift up the cutting unit by pulling the lever back to the end position. MAX 15° 2. Pull back the throttle control and turn the ignition key to the STOP position. STOP START Release lever In order to move
  • Husqvarna K 1260 | Owners Manual - Page 19
    joints and shafts 3) 27 q Check and adjust the throttle wire 28 q Clean the engine's and hydrostat's cooling flanges 2,4) - r Replace the air filter's pre-filter and paper filter 2) 22 q Replace the fuel filter 28 q Replace the plug - r 1) First change after 5 hours. 2) During
  • Husqvarna K 1260 | Owners Manual - Page 20
    MAINTENANCE Dismantling of the machine hoods Engine hood The engine is accessible for servicing when the engine hood is lifted up. Tilt the seat forward, release the rubber strap under the seat, and tilt the hood backwards. Front hood
  • Husqvarna K 1260 | Owners Manual - Page 21
    , grass and dirt. If the cooling intake is blocked this will interfere with the cooling of the engine, which can damage the engine. FULL Checking of the fuel pump's air filter Check regularly that the fuel pump's air filter is free from dirt. The filter can when necessary be cleaned with a brush
  • Husqvarna K 1260 | Owners Manual - Page 22
    wires by pushing them together as shown in the diagram. It should be possible to push them together so that the distance between them is half as much, without using unnecessary force. 3. When necessary the wires can be tensioned by tightening the adjusting nuts, one on each side of the steering rim
  • Husqvarna K 1260 | Owners Manual - Page 23
    by removing the water. Contact a doctor as soon as possible. Batteries emit explosive gas. Sparks , flames and cigarettes must absolutely not be brought into the vicinity of the battery. Check the safety system The machine is equipped with a safety system which prevents starting the cutting
  • Husqvarna K 1260 | Owners Manual - Page 24
    for correct service interval). The air filter is replaced as follows: 1. Dismantle the engine hood as described on page 18. 2. Remove the air filter housing's plastic cover by releasing the wing-nut. 3. Remove the wing-nut on the air filter and lift off the paper filter with pre-filter. 4. Pull off
  • Husqvarna K 1260 | Owners Manual - Page 25
    as follows: 1. Place a set of bathroom scales under the cutting unit's frame (front edge) so that it rests on the scales. If necessary a block can be placed between the frame and scales so that the support wheels do not bear any weight. 2. Adjust the unit's ground pressure by screwing in or out the
  • Husqvarna K 1260 | Owners Manual - Page 26
    18. 2. Vertical adjustment of the cutting unit is made with the adjusting nuts on the back edge of the lift-strut. 2 3. Raise the cutting unit at the front . Fit the right-hand fender and the front hood. Adjustment of Rider 970 1. Dismantle the front hood and right-hand fender as described
  • Husqvarna K 1260 | Owners Manual - Page 27
    5. Push the unit backwards and dismantle the drive belt. Remove the hair-needle spring and release the crossbar (6) from the height adjustment. The unit can now be pulled forward until it releases from the rear suspension. Fitting of the cutting unit takes place in the reverse order to dismantling
  • Husqvarna K 1260 | Owners Manual - Page 28
    ' attachment screws are tight. IMPORTANT INFORMATION Replacing or sharpening the blades should be conducted by an authorised service workshop. IMPORTANT INFORMATION On the Bioclip unit the relative positioning of the blades should always be as shown in the diagram with an angle of 90° between the
  • Husqvarna K 1260 | Owners Manual - Page 29
    plug, located on the left-hand side of the engine. 2. Remove the dip stick and drain plug. 3. Let the oil run out into the receptacle. 4. Fit the drain plug and station for treatment. Avoid skin contact, wash with soap and water in the event of spillage. Lubrication The following two lubrication
  • Husqvarna K 1260 | Owners Manual - Page 30
    the throttle wire may need adjusting. 1. Release the clamping screw (see arrow) and push the throttle control to full throttle position. 2. Pull the throttle wire's outer casing to the far right and tighten the clamping screw. Replacement of the fuel filter Replace the pipe fitted fuel filter every
  • Husqvarna K 1260 | Owners Manual - Page 31
    , too high. • Carburettor incorrectly set. • Air filter clogged. • Fuel tank vent blocked. • Ignition setting defective. • Dirt in fuel pipe. Engine seems to have no power. • Air filter clogged. • Plug defective. • Dirt in carburettor or fuel pipe. • Carburettor incorrectly set. Engine overheats
  • Husqvarna K 1260 | Owners Manual - Page 32
    cutting unit. Touch-up paint damage to avoid rust. 2. Inspect the machine for worn or damaged parts and tighten loose screws and nuts. 3. Change the oil, and take care of the waste oil. 4. Empty the fuel tank. Start the engine and run it until the carburettor is emptied of fuel. 5. Remove the plug
  • Husqvarna K 1260 | Owners Manual - Page 33
    pressure, front & rear Max. gradient Engine Manufacture Power Displacement Fuel Tank volume Oil Oil volume Start Electrical system Type Battery Spark plug Transmission Manufacture Oil Cutting unit Type Cutting width (Bioclip) Cutting height Blade diameter (Bioclip) NOISE LEVEL Rider 850 2000 mm
  • Husqvarna K 1260 | Owners Manual - Page 34
    NOTES ... 32 - English ´*2}^¶6j¨
  • Husqvarna K 1260 | Owners Manual - Page 35
    English - 33
  • Husqvarna K 1260 | Owners Manual - Page 36
    ´*2}^¶6j¨
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
101 89 36-26
Rider 850 HST
Rider 970 HST
Operator´s manual
Please read these instructions carefully and make sure
you understand them before using the machine.
RIDER 850
RIDER 850
RIDER 850
RIDER 850
RIDER 850
RIDER 850
RIDER 970
RIDER 970
RIDER 970