Husqvarna MZ 61 Owners Manual
Husqvarna MZ 61 Manual
 |
View all Husqvarna MZ 61 manuals
Add to My Manuals
Save this manual to your list of manuals |
Husqvarna MZ 61 manual content summary:
- Husqvarna MZ 61 | Owners Manual - Page 1
10% ethanol (E10) is acceptable for use in this machine.The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Operator Manual MZ61 / 967277502 Please read the operator manual carefully and make sure you understand the instructions before using the machine. - Husqvarna MZ 61 | Owners Manual - Page 2
practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower. Each person operating the mower must be of sound mind and body and must not be under the - Husqvarna MZ 61 | Owners Manual - Page 3
25 Deck Belt Removal 25 Pump Belt 26 Cutting Blades 26 Blade replacement 26 Adjusting the Mower Deck 27 Leveling deck 27 Cleaning 27 LUBRICATION 28 Wheel and Deck Zerks 28 Front Wheel Mount 28 Front Wheel Bearings 28 Deck Spindles 28 Engine oil change 29 Transaxle (Transmission) Fluid - Husqvarna MZ 61 | Owners Manual - Page 4
regulated by steering controls both contribute to the machine's performance. This manual is a valuable document. Read the contents carefully before using or servicing the machine. The following of instructions (use, service, maintenance) by all who operate this machine is important for the - Husqvarna MZ 61 | Owners Manual - Page 5
adjusted by your retailer. See the certificate in the Service Journal in this operator manual. When you need spare parts or support in service questions, warranty issues, etc., please consult the following professional: This Manual belongs to the machine with the manufacturing number: Manufacturing - Husqvarna MZ 61 | Owners Manual - Page 6
neglect to follow instructions given in the manual. Used also parts Battery acid is corrosive, explosive and flammable Shut off engine before performing Read Operator Manual maintenance or repair Keep a safe distance from the machine Warning! Rotating blades, keep away from the discharge deck - Husqvarna MZ 61 | Owners Manual - Page 7
SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Read, understand, and follow all instructions on the machine and in the manual before exhaust or engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause buildup to occur. Clean any oil or fuel - Husqvarna MZ 61 | Owners Manual - Page 8
may lose traction. • Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope. WARNING! minimum of 16 years of age before operating a riding lawn mower. Children Tragic accidents can occur if the operator is not alert - Husqvarna MZ 61 | Owners Manual - Page 9
be started until problem has been resolved. mower deck's drive belt is removed. • Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Adjust and service safety and instruction labels, buildup. Clean oil or fuel spillage - Husqvarna MZ 61 | Owners Manual - Page 10
and service as necessary. • The mulch blades deck and underside of deck, avoid spraying engine and electrical components with water. Transport Towing If machine is equipped with a tow hitch, use extreme caution when towing. Never allow children or others in or on towed equipment.. Make wide turns - Husqvarna MZ 61 | Owners Manual - Page 11
manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a Briggs & Stratton four-stroke overhead valve engine. Transmission from the engine is made via a belt-driven hydraulic control 7. Ignition switch 8. Service meter 9. Throttle control 10. Blade switch 11. Seat adjustment lever - Husqvarna MZ 61 | Owners Manual - Page 12
turn reduced and the machine turns to the right. Zero turn can be achieved by The rotation direction when zero turning is determined by control is pulled backward, the machine turns to the left. Use extra care the park brake before moving the mower. Ignition Switch Forward Neutral Reverse Neutral - Husqvarna MZ 61 | Owners Manual - Page 13
hours, before an automatic reset occurs. To service the engine and mower, see the Service Journal of this manual. NOTE: The service minder operates (clocks hours) only when the engine is running. Choke Control To engage the mower deck, pull the knob out; mower blades are disengaged when the knob is - Husqvarna MZ 61 | Owners Manual - Page 14
the primary fuse. The 7.5 A is for the mower deck coupling. Seat Adjustment Lever The desired cutting height is set with the height Manual Transport in the Operation section. The fuel shut off valve is located at the left rear of the seat. The valve is off when the handle tab is turned - Husqvarna MZ 61 | Owners Manual - Page 15
engine while in storage. To avoid engine problems, the fuel system should be emptied before oil or fuel. Do not store, spill or use gasoline near an open flame. Read the safety instructions to help insure good cold weather starting. If the mower is not tracking straight, check the air pressure in - Husqvarna MZ 61 | Owners Manual - Page 16
zero turn mowers are far more maneuverable than typical riding mowers. This section should be reviewed in its entirety prior to attempting to move the mower under its own power. When first operating the mower . 5. Set the deck cutting height by inserting started: • The blade switch must be pressed - Husqvarna MZ 61 | Owners Manual - Page 17
the Engine 1. Sit on the seat. 2. Raise the mower deck to the transport position by locking the lift pedal fully lever fully upwards. 4. Disengage the mower blades by pressing the blade switch downwards. 7. Open the fuel tank valve. 8. Press in and turn the ignition key to the start position - Husqvarna MZ 61 | Owners Manual - Page 18
. Stopping the Engine 1. Move the throttle to the minimum position (tortoise symbol). 2. Move the steering controls outward. 4. Move throttle control to full throttle. 5. Engage the mower deck by pulling up the blade switch. 3. Disengage the mower deck by pressing the blade switch down. 18 - Husqvarna MZ 61 | Owners Manual - Page 19
mower deck underside with water after each use. When cleaning, the mower deck shall be raised into the transport position. Make sure the mower the Safety Instructions Driving on Slopes in the Safety Instructions. 1. of the mower and press forward to regain forward motion. 6. Make all turns slowly. - Husqvarna MZ 61 | Owners Manual - Page 20
the rear of the unit below the rear engine plate. 1. Raise the deck to the highest (transport) position. 2. Pull the release levers up and out injury or death if the machine falls off the ramps. IMPORTANT INFORMATION The mower is equipped with a 12-volt negative grounded system. The other vehicle - Husqvarna MZ 61 | Owners Manual - Page 21
fuel and oil leakages Check/clean the engine's cooling air intake Check the mower deck Check for loose hardware (screws, nuts) Clean under the mower deck Start the engine and blades, listen for unusual sounds Check for damage Thoroughly clean around the engine Clean around belts, belt pulleys Check - Husqvarna MZ 61 | Owners Manual - Page 22
2) Check the hydraulic oil in the oil tank Change the hydraulic oil (every 300 hours) Replace the hydraulic oil filter (every 300 hours) Dismantle and inspect starter 3) (every 300 hours) Check/adjust the mower deck Check the engine valve clearance 3) Perform the 300-hour service 3) Daily Before - Husqvarna MZ 61 | Owners Manual - Page 23
MAINTENANCE Battery Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the terminal guard and lift off guard. 5. Carefully remove the battery from the mower. 6. Install new battery with terminals in the same position as the old battery - Husqvarna MZ 61 | Owners Manual - Page 24
• The mower deck is disengaged. the Husqvarna service workshop turn the machine off and repair the safety system before using the machine again. Make sure the engine stops when the park brake is not engaged and the operator leaves the seated position. Check that the engine stops if the mower blades 24 - Husqvarna MZ 61 | Owners Manual - Page 25
to your dealer for service. Foam filled tires support the deck. 7. Remove the belt from around the electric clutch on the engine shaft and off the mower deck. Deck Belt Installation NOTE: For ease in installing the deck belt, refer to the routing decal on the top of the deck. 1. Wrap the deck belt - Husqvarna MZ 61 | Owners Manual - Page 26
. 8. Reinstall the deck belt. (See Deck Belt Installation in this section of the manual). Cutting Blades For the best mowing results, it is important that blades are well sharpened and not damaged. Replace blades that have been bent or cracked when hitting obstacles. Let the service workshop decide - Husqvarna MZ 61 | Owners Manual - Page 27
mower deck drive belt must be installed prior to leveling deck. 1. Wear heavy gloves. Turn each outer blade tip to align with the deck side-to-side. 4. Confirm measurements again. Blade the blade tip on the discharge side of the mower deck. , especially under the mower deck, will increase the - Husqvarna MZ 61 | Owners Manual - Page 28
Week 1/365 Every day Lubricate with grease gun Filter change Oil change Level check General Remove the ignition key to petroleum products must not be used to clean belts. Deck Spindles Lower the cutting deck completely. If a grease gun without rubber hose belts or belt pulley drive surfaces. 28 - Husqvarna MZ 61 | Owners Manual - Page 29
for ease of maintenance. To ensure constant fluid quality levels and longer life, an oil filter change interval of every 200 hours is recommended. The following procedure is performed with the transaxles installed in the mower and the mower on level ground. Apply the pump release valve for each - Husqvarna MZ 61 | Owners Manual - Page 30
from the system. When the hydraulic drive operates at normal noise levels and moves smoothly forward and reverse at normal speeds, the hydraulic drive is considered purged. 5. After the vehicle has been used two times, the oil level should be checked while the oil is cold and adjusted accordingly - Husqvarna MZ 61 | Owners Manual - Page 31
or has come off Air trapped in hydraulic system Mower deck not engaging Drive belt for the mower deck has come loose Contact for the electromagnetic coupling has loosened Blade switch is faulty or has come loose from cable contact Blown fuse Transaxle leaks oil Damaged seals, housing, or gaskets Air - Husqvarna MZ 61 | Owners Manual - Page 32
for storage: 1. Thoroughly clean the machine, especially under the mower deck. Touch up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion. 2. Inspect the machine for worn or damaged parts and tighten any nuts or screws that may have become loose - Husqvarna MZ 61 | Owners Manual - Page 33
SCHEMATIC 33 - Husqvarna MZ 61 | Owners Manual - Page 34
Kawasaki Cutting Width FR730V Cutting Height 24 hp 1) Uncut Circle Pressure with oil filter Number of Blades Min 87 octane unleaded (Max Blade Length ethanol 10%, Max MTBE 15%) 5 gallons / 18.9 liters Nose Roller Air cooled Sprung Seat Standard Hinged Arm Rests 12V Service . 61" - Husqvarna MZ 61 | Owners Manual - Page 35
bolt Deck pulley bolts Lug nuts Blade bolt ) 52 ft/lb (70 Nm) 80 ft/lb (110 Nm) Accessories Collection system HEX HEAD CAP SCREWS The torque values shown should be used 13 18 Shank Size (Diameter in inches, fine or coarse thread) 5/16 18 24 28 38 24 33 3/8 31 42 46 62 40 54 7/16 50 - Husqvarna MZ 61 | Owners Manual - Page 36
switch for the mower deck. Safety switch in the seat. Safety switch in the steering controls. Parking brake functionality. Driving forward. Driving backward. Engaging the blades. Check engine high idle speed Inform the customer about: Need and advantages of following the service schedule Need and - Husqvarna MZ 61 | Owners Manual - Page 37
hydraulic filter Check neutral position Check safety system Check seat belt Check fuel system for leaks Inspect safety guards and shields Check brake adjustment SERVICE JOURNAL Date, mtr reading, stamp, sign r r r r r r r r r r r Action Daily Service Clean debris from mower Check engine oil - Husqvarna MZ 61 | Owners Manual - Page 38
JOURNAL Action 25-Hour Service Check the fuel pump's air filter Sharpen/Replace mower blades if required Check the tire pressures Check battery with cables Lubricate according to lubrication chart Check/clean the engine's cooling air intake Clean the air cleaner's foam pre-filter Date, mtr reading - Husqvarna MZ 61 | Owners Manual - Page 39
Clean underside of deck Check blade pitch Grease blade spindles Inspect spindle bearings Inspect deck belt and blades Inspect idler arm bearings Inspect deck idler pulleys Check hydraulic oil level Inspect hydraulic filter Inspect hydraulic drive belt Inspect hydraulic hoses Check neutral position - Husqvarna MZ 61 | Owners Manual - Page 40
RPM Clean underside of deck Check blade pitch Grease blade spindles Inspect spindle bearings Inspect deck belt and blades Inspect idler arm bearings Inspect deck idler pulleys Change hydraulic oil Change hydraulic filter Replace hydraulic drive belt Inspect hydraulic hoses Check neutral position - Husqvarna MZ 61 | Owners Manual - Page 41
SERVICE JOURNAL Action At Least Once Each Year Clean the engine's cooling air intake (25 hours) Replace the air cleaner's foam pre-filter (300 hours) Replace the air filter's paper cartridge Change the engine oil (50 hours) Replace the engine oil filter (100 hours) Check/adjust the cutting height - Husqvarna MZ 61 | Owners Manual - Page 42
Action SERVICE JOURNAL Date, mtr reading, stamp, sign 42 - Husqvarna MZ 61 | Owners Manual - Page 43
- Husqvarna MZ 61 | Owners Manual - Page 44
115 666627 Rev A www.husqvarna.com 2013-11-15
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
 |
 |
Operator Manual
Please read the operator manual carefully and make sure you
understand the instructions before using the machine.
Gasoline containing up to 10% ethanol (E10) is
acceptable for use in this machine.The use of any
gasoline exceeding 10% ethanol (E10) will void
the product warranty.
MZ61 / 967277502