Husqvarna SC18 Owners Manual
Husqvarna SC18 Manual
 |
View all Husqvarna SC18 manuals
Add to My Manuals
Save this manual to your list of manuals |
Husqvarna SC18 manual content summary:
- Husqvarna SC18 | Owners Manual - Page 1
Operators manual Please read these instructions carefully and make sure you understand them before using the machine. Models: SC18/968981201 SC18/968999352 MANUAL NO. 540200156 REV. 01 (12/01/05) - Husqvarna SC18 | Owners Manual - Page 2
5 Sod Cutting 5 Maintenance and Service Instructions Page Safety and Maintenance 6 Safety ...6 Engine Service and Warranty 6 Lubrication Schedule 6 Inspection Schedule 6 Blade Wear 7 Cleaning ...7 Service ...7 Adjusting Chain Tension 7 Storage ...7 Trouble Shooting Guide 8 Sound - Husqvarna SC18 | Owners Manual - Page 3
in the Clutch/Gear Box 1. Refer to your engine manual for oil type, viscosity, weight and capacity. Reducer (yellow cap) Transmission grease used 1. You should not need to service the transmission. Call Tecumseh or your servicing dealer if needed. 2. Transmission is located directly behind the - Husqvarna SC18 | Owners Manual - Page 4
OPERATING INSTRUCTIONS GENERAL INFORMATION This manual will assist you in the safe operation and proper maintenance of your Husqvarna equipment. Read it thoroughly before attempting to operate the machine. Do not hesitate to call your dealer or Husqvarna if additional information is required. The - Husqvarna SC18 | Owners Manual - Page 5
OPERATING INSTRUCTIONS • Do not attempt sharp turns while cutting. • Should I water engine oil is at engine manufacturer's recommended level. (Refer to engine manufacturer's manual.) • Put the sod cutter into neutral before starting. • Place blade in transport position before starting. TRANSPORTING - Husqvarna SC18 | Owners Manual - Page 6
durability. For reliability and preservation of design safety standards, replacements should only be made with genuine Husqvarna parts or material of equivalent type and strength. TWO MINUTE WARNING Sod Cutters may be tipped on their engine guard for cleaning and access for no more than 2 minutes - Husqvarna SC18 | Owners Manual - Page 7
prolong the service of your machine. Note: Use care with power washers to avoid damage to Warning Decals, Operator Instruction Labels, Bearings • Install chain guard. • Set sod cutter back to level. STORAGE 1. Refer to engine manufacturer's instructions for engine storage information. 2. Clean - Husqvarna SC18 | Owners Manual - Page 8
PROBLEM TROUBLESHOOTING ANSWER/COMMENT Transmission shaft broke 1. Ensure debris is not caught in the Transmission Chain or wrapped around the transmission output shaft. 2. Ensure the unit has a Skid Pan installed. 3. Contact your servicing dealer. Drive wheels won't engage 1. Ensure the Drive - Husqvarna SC18 | Owners Manual - Page 9
PROBLEM TROUBLESHOOTING has double set screws. 2. Replace any damaged parts. 3. Use blue loctite on the set screws 1/2", pivoting the machine back on its rear wheels while cutting can cause machine to cut too deeply cause it to slip. Replace with a Husqvarna belt. 4. Tension can be increased by - Husqvarna SC18 | Owners Manual - Page 10
PROBLEM Blade not disengaging Belt coming off Belt glazed or slipping TROUBLESHOOTING ANSWER/COMMENT New Unit or New Belt pulley clears Belt Keeper when engaged. 2. Be sure the correct Husqvarna belt is being used. If not, replace with a Husqvarna belt. 3. Belt Idler Pivot Bolt may be too tight or - Husqvarna SC18 | Owners Manual - Page 11
PROBLEM Belt glazed or slipping Depth Control Rod broke Depth Control Rod will not turn (frozen) Unit is creeping Handle Stand Off Kit how to tighten bolts Bolts breaking Tires wearing too quickly TROUBLESHOOTING dealer or servicing dealer. wheels to axle. 1. Only cut in first or second gear. 2. Tire - Husqvarna SC18 | Owners Manual - Page 12
SOUND AND VIBRATION STATMENT 12 - Husqvarna SC18 | Owners Manual - Page 13
This page left black intentionally 13 - Husqvarna SC18 | Owners Manual - Page 14
Technical assistance: For technical assistance please contact your Local Dealer.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
Operators manual
SC18/968981201
SC18/968999352
Models:
Please read these instructions carefully and make
sure you understand them before using the machine.
MANUAL NO. 540200156 REV. 01 (12/01/05)