IC Realtime IPEL-E80F-IRW1 Product Manual

IC Realtime IPEL-E80F-IRW1 Manual

Get IC Realtime IPEL-E80F-IRW1 PDF manuals and user guides View all IC Realtime IPEL-E80F-IRW1 manuals
Add to My Manuals
Save this manual to your list of manuals

IC Realtime IPEL-E80F-IRW1 manual content summary:

  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 1
    Network Camera Web3.0 Operation Manual Version 1.0.1 i
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 2
    Table of Contents 1 Network Config...1 1.1 Network Connection ...1 1.2 Log in ...1 2 Live ...6 2.1 Encode Setup ...6 2.2 System Menu...7 2.3 Video Window Function Option 7 2.4 Video Window Setup ...8 2.4.1 Image Adjustment...8 2.4.2 Original Size ...9 2.4.3 Full Screen ...9 2.4.4 Width and Height
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 3
    5.1.1 Conditions...30 5.1.2 Video ...41 5.1.3 Audio ...53 5.2 Network...56 5.2.1 TCP/IP ...56 5.2.2 Connection...58 5.2.3 PPPoE ...60 5.2.4 DDNS ...61 5.2.5 IP filter ...62 5.2.6 SMTP （e-mail) ...63 5.2.7 UPnP ...64 5.2.8 SNMP ...65 5.2.9 Bonjour ...68 5.2.10 Multicast ...68 5.2.11 4G ...69 5.2.12
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 4
    5.5.6 Remote control ...131 5.5.6 Auto Maintenance 132 5.5.7 Upgrade ...133 5.6 Information ...133 5.6.1 Version...133 5.6.2 Log...134 5.6.3 Online User ...134 6 Alarm...136 7 Log out ...138 iv
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 5
    Important The following functions are for reference only. Some series products may not support all the functions listed below. v
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 6
    Internet, you need to have its IP address. User can use Config Tool to search IP of the network camera. Please refer to Config Tool manual. 1.2 Log in It needs to install WEB plug-in when you use WEB client for the first time, the exact operation steps are shown as
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 7
    After successful connection, the login interface is shown as in Figure 1-3; input your user name and password. Default factory username is admin and password is admin. Figure 1-3 The system will display "Update Password" prompt box for your first login, users need to modify the password and save it
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 8
    Figure 1-5 Click on "Please click here to download and install the plug-in". The system pops up warning information to ask you whether run or save this plug-in. See Figure 1-6. Figure 1-6 3
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 9
    You must either run or save the file to local and install it. Follow the following steps. Click on run, you will see Figure 1-7and Figure 1-8. Figure 1-7 4
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 10
    Figure 1-8 When plug-in installation completes, the installation page closes automatically. The web-end will refresh automatically, and then you can view video captured by the camera. Figure 1-9 5
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 11
    setup bar  Section 2: System menu  Section 3: Window function option bar  Section 4: Window adjust bar Figure 2-1 2.1 Encode Setup Note: Some series don't support sub stream 2. The encode setup interface is shown as in Figure 2-2. Figure 2-2 Please refer to the following sheet for detailed
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 12
    Parameter Main stream Sub Stream 1 Sub Stream 2 Protocol Function Click it to enable main stream video monitoring and click again to disable it. Generally for storage and monitor. Click it to enable Sub Stream 1 video monitoring and click again to disable it. When network bandwidth is insufficient,
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 13
    2 Digital Zoom  When the video is in the original status, click it you can select any zone to zoom in. In the non-original status, you can drag the zoom-in zone in specified range. Right click mouse to restore previous status.  Click it; you can use the middle button of the mouse to zoom in/
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 14
    Figure 2-6 Click this button to display/hide image control interface. Click it to open picture setup interface. This interface is on the top right pane. Please refer to the following sheet for detailed information. Parameter Function Video setup It is to adjust monitor video brightness. It is
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 15
    of preview interface, as shown in Figure 2-7, click left mouse button to adjust focus zooming configuration. Note: · The product series which support motorized zoom, synchronous focus and back focus have this button. · Auto-focus after zoom and focus adjustment. 2.4.8 Fisheye/Trigger Track Click
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 16
    Parameter Function Zoom Adjust the focal length of the lens by clicking or long pressing "+""-"buttons. Step length is used to adjust the length of one step with one click. Focus Adjust the sharpness of the lens by clicking or long pressing"+"、"-" buttons. Step length is used to adjust the
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 17
    Mode Figure 2-8 Note Three modes which are ceiling mount, wall mount and ground mount. It represents the display mode of the current image (default supports original image mode), the display modes may be different according to different installation modes. It is shown as follows:  Ceiling: 1P+1、2P
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 18
    rectangular panorama+8 independent sub images, both the sub images and the sub box in the expanded rectangular panorama support zoom and movement, expanded rectangular panorama supports up and down movement and changes vertical angle of view. Figure 2-9 Enable the trigger track on the interface
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 19
     1P: Original picture  1P+3: Original picture and three trigger track windows, it can adjust the location and size of three trigger track windows on the original picture.  1P+5: Original picture and five trigger track windows, it can adjust the location and size of five trigger track
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 20
    set PTZ protocol. (Please refer to Ch. 5.5.3). Currently only IPC-HFXXXX series and -PT series products can support PTZ function. Parameter Note PTZ direction  PTZ supports eight directions: left/right/up/down/upper left/upper right/bottom left/bottom right. Speed It controls rotation speed
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 21
    Figure 3-2 PTZ setting interface is shown as in Figure 3-3. Here you can set scan, preset, tour, pattern, assistant function and light and wiper plus view coordinate. Figure 3-3 3.1 Scan Scan interface is shown in Figure 3-4. 16
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 22
    Steps to scan are: Figure 3-4 Step 1. Click on Set button, display icon. Step 2. Move via direction key to select left, click on Set Left to set left border of camera Step 3. Move via direction key to select right, click on Set Right to set right border of camera. Step 4. Complete scan path
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 23
    Tour interface is shown in Figure 3-6. Figure 3-6 Steps to tour are: Step 1. In tour box, input tour path value. Step 2. Click on Add. Range of tour relates to PTZ protocol. Step 3. In preset box, input preset value. Step 4. Click on Add as to add a preset in this tour. If click on Del, it deletes
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 24
    Click "Stop Rec" to complete the setting of a pattern path. Step 4 Click "Start" and it will start pattern according to the pattern spot which has been set; click "Stop" and the pattern ends. 3.5 Assistant Assistant interface is shown in Figure 3-8. Figure 3-8 Steps to assistant are: Step 1. In
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 25
    4 Playback Web client playback supports video playback and picture playback. Note: Before playback, user shall set storage management as in Ch. 5.4. 4.1 Playback The playback interface is shown as in Figure 4-. 6 2 1 3 4 5
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 26
    4.1.1 Function of Play The function of play is shown as in Figure 4-2 and Figure 4-3. Figure 4-2 Figure 4-3 Parameter Function ① Play When you see this button, it means pause or not played record. Click on this button, switch to normal play status. ② Stop Click this button to stop playing. ③
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 27
    file progress bar in color. While, green represents normal record, yellow represents motion detect record, red represents alarm record, and blue represents manual record. Step 2. Click on certain time on progress bar, playback starts from this time. See Figure 4-5. Figure 4-5 Step 3. Click on file
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 28
    time on the date. There are two formats: dav, mp4. Download  Click the download button and download file to path in Ch. 5.1.2.5.  System does not support download and playback at the same time. 23
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 29
    Parameter Back Function Click on back button to go to calendar interface. 4.1.3 Playback Cut Note: Playback cut function will automatically pause playing record as playback cut and playback cannot be at the same time. Step 1. Click on start time to cut on time axis. This time must be within
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 30
    Parameter 24 hours 2 hours 1 hour 30 min Figure 4-9 Function Click on it, means video in past 24 hours. Click on it, means video in past 2 hours. Click on it, means video in past 1 hour. Click on it, means video in past 30 min. 4.1.6 Assistant Function Video playback assistant function is shown in
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 31
    4.2.1 Play Figure 4-11 Figure 4-12 Default icon is and it means pause or not played picture. Click on play button to switch to normal play status. Icon become Click on it to pause. 4.2.2 Playback File 26
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 32
    Figure 4-13 Step 1. Click on file list , select snapshot file of the date. Step 2. Double click on file in list, to play this snapshot. Parameter Function Search It means all snapshot files within the start time and end time of selected date. 27
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 33
    Parameter Download Back Function Click the download button to open snapshot file or directly download to local according to the browser types. Click on back button to return to calendar interface and re-select time. 4.2.3 Snapshot Type Figure 4-14 28
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 34
    After checking snapshot file type, in file list only display file of selected type. Users can also select the snapshot type to be displayed via the dropdown box above the file list. See Figure 4-. Figure 4-15 29
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 35
    may be different according to different models, please refer to the actual product for more details. 5.1.1.1 Picture Note: The device which supports true WDR fails to support long exposure when true WDR is enabled. Step 1 Select "Setup > Camera > Conditions > Picture" and the system will display the
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 36
    flip mode for some devices. It can realize electronic anti-flicker function via comparison algorithm of image difference, which can effectively solve the problem of image jittering during application and it can make the image clearer. Step 3 Click "Save" and complete the image parameter config of
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 37
    5.1.1.2 Exposure Step 1 Select "Setup > Camera > Conditions > Exposure". The system will display the "Exposure" interface which is shown in Figure 5-2. Figure 5-2 Step 2 It is to set the exposure parameter, please refer to the following sheet for more details. Parameter Note Anti-flicker 
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 38
    reached the upper limit or lower limit, the device can auto adjust the gain value to make the image reach the best brightness.  Manual: It is to manually set gain value and shutter value, adjust the the displayed brightness of the image. It can set the parameter when the camera installs auto
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 39
    Step 3 Click "Save" to complete the parameter config of camera exposure. 5.1.1.3 Backlight Backlight mode can be divided into BLC, WDR and HLS. BLC: it can avoid cucoloris phenomenon of the darker area in the backlight environment. WDR: It can suppress the overbright area and compensate darker area
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 40
     When selecting "Customized" mode, the system can realize exposure upon the selected area after it set customized area, which is to make the image of the selected area reach appropriate brightness.  When the "Mode" is set as "WDR", it will lower the brightness of the area with high brightness and
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 41
    most outdoor scenes with natural light and artificial light, which is to make the image color normal.  When the "Mode" is set as "Manual", it can manually set the value of red gain and blue gain; the system can compensate the different color temperatures in the environment according to the settings
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 42
    Step 2 Set day & night parameter; please refer to the following sheet for more details. Parameter Note Mode Sensitivity Delay It is to set the camera image displayed as color or black & white mode. Note: The setting of "Day/Night Mode" is not affected by the setting of "Profile Management". It
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 43
    adjust the image definition according to the intensity and air light mode which have been set previously. As for air light mode, you can set manual or auto.  When the "Mode" is set as "Auto", the system will auto adjust the image definition according to the actual scene.  When the "Mode
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 44
    disable far light when the focal length of the lens is adjusted to a certain wide angle, which is to avoid near overexposure. Meanwhile, it can manually set light compensation to slightly adjust the brightness of IR light.  When the "mode" is set as "Off", it will not enable the IR light
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 45
    Step 2 Set profile management.  When the "Profile Management" is set as "Normal", the system will monitor according to the normal config. Figure 5-8  When the "Profile Management" is set as "Full Time", you can select "Always Enable" in "Day" or "Night', the system will monitor according to the
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 46
    5.1.1.9 Zoom and Focus Note: Only motorized vari-focal devices support focus and zoom function. Step 1 Select "Setup > Camera > Conditions > Zoom and Focus" and the system will display the interface of "Zoom and Focus" which is
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 47
    5.1.2.1 Video Step 1 Select "Setup > Camera > Video > Video" and the system will display the interface of "Video" which is shown in Figure 5-12 or Figure 5-13. Figure 5-12 (Non fisheye) Figure 5-13 (Fisheye) Step 2 42
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 48
    zoom and movement.  2R: Original image + 2 independent sub images, the sub boxes of the original image can support zoom and movement, the sub image supports up and down movement, which can change the vertical angle of view. Note: The device end will output dewarped video stream after configuring
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 49
    fps to record. There are two options: VBR and CBR. Please note you can set video quality in VBR mode. Note: WEB interfaces don't support motion detect and alarm code stream setting. There are five options: H.264 (main profile standard, H.264H (high profile standard), H.264B (Baseline Profile), H.265
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 50
    Parameter Bit Rate SVC I Frame Watermark Settings Watermark Character Function  In CBR, the bit rate here is the max value. In dynamic video, system needs to low frame rate or video quality to guarantee the value.  The value is null in VBR mode.  Please refer to recommend bit rate for the
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 51
    Figure 5-14 3. Select the needed resolution and clip the needed image on the interface, which is shown in Figure 5-15. 4. Click "Save". You can check the clipped video in the preview interface (the sub stream 2 preview interface only displays the clipped area), which is shown in Figure 5-15. 46
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 52
    Figure 5-15 Step 3 Click "Save" to complete video stream setup. 5.1.2.2 Snapshot The snapshot interface is shown as in Figure 5-16. Figure 5-16 Please refer to the following sheet for detailed information. 47
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 53
    Parameter Snapshot type Image size Quality Interval Function There are two modes: general (schedule) and Event (activation). It is the same as the resolution of main stream. It is to set the image quality. There are six levels. It is to set snapshot frequency. Optional1~7s/picture, customized.
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 54
    Figure 5-18 Figure 5-19 49
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 55
    Figure 5-20 Figure 5-21 50
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 56
    Time Title Channel Title Text Overlay Picture Overlay Counting  Here you can privacy mask the specified video in the monitor video.  System max supports 4 privacy mask zones.  You can enable this function so that system overlays time information in video window.  You can use the mouse to
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 57
    . You can click on Refresh to see effect.  Click it to restore default config.  Click it to complete video settings. 5.1.2.4 ROI Note: Some series don't support ROI setup function. Figure 5-23 52
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 58
    is locally logged in PC account. Please click the Save button to save current setup. Figure 5-25 5.1.3 Audio Please note some series devices do not support audio function. 5.1.3.1 Audio The audio interface is shown as below. See Figure 5-26. 53
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 59
    Figure 5-26 Please refer to the following sheet for detailed information. Parameter Function Enable You can enable audio only when video is enabled. After selecting the "Enable" of main stream or sub stream, the network transmission stream is the audio/video composite stream, otherwise it only
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 60
    Microphone Volume Speaker Volume Adjust microphone volume from 0～100. Note: Supported by some devices. Adjust speaker volume from 0～100. Note: Supported by some devices. 5.1.3.2 Alarm audio Figure 5-27 Figure 5-28 Audio management currently supports PCM format to record and PCM, wav two forms to
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 61
    " to download. 5.2 Network 5.2.1 TCP/IP The TCP/IP interface is shown as in Figure 5-29. It supports IPv4 and IPv6. IPv4 supports static IP and DHCP. IPv6 supports static IP only. When users manually modify IP address, WEB will automatically jump to the new IP address. Figure 5-29 Please refer to
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 62
    subnet mask and the default gateway. Preferred DNS DNS IP address. Alternate DNS Alternate DNS IP address. Enable ARP/Ping set device IP address service. You can use ARP/Ping command to modify or set the device IP address if you know the device MAC address. Before the operation, please
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 63
    Figure 5-30 5.2.2 Connection 5.2.2.1 Connection The connection interface is shown as in Figure 5-31. Figure 5-31 Please refer to the following sheet for detailed information. Parameter Function Max It is the max Web connection for the same device. The value ranges from 1 connection to 20.
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 64
    can leave it in blank if it is the default value. Follow standard RTP protocol and when encode mode is MJPEG, the max resolution only supports 2040*2040. HTTPs Port HTTPs communication port, range is 1025~65534, default is 443. Note:  0～1024, 37780～37880, 1900, 3800, 5000, 5050, 9999, 37776
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 65
    5-32 5.2.3 PPPoE The PPPoE interface is shown as in Figure 5-33. Enter the PPPoE username and password which are provided by ISP (Internet Service Provider), and click "Enable". The network camera will automatically establish network connection in the mode of PPPoE after it is enabled, after it is
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 66
    servers so that you can access the system via the server. Please go to the corresponding service website to apply a domain name and then access the system via the domain. It works is auto, it can select manual Both auto and manual are "MAC addresss.icddns.com" by default, it is able to set prefix
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 67
    can set prefix by themselves. Test It is to test if the domain name can be used or not. The parameter exists only when selecting "manual" in "Mode". Username The user name you input to log in the server, optional. 5.2.5 IP filter The IP filter interface is shown as in Figure
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 68
    Here you can add IP address and MAC address. You must add these addresses before enabling the trusted sites. Please note: You must set MAC address in the same network segment. Figure 5-36 5.2.6 SMTP （e-mail) The SMTP interface is shown as in Figure 5-37. Figure 5-37 Please refer to the following
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 69
    is 25. You can modify it if necessary. For the server which supports the anonymity email function, it won't display the information of the sender. Click the "Add/Remove Windows Components" and then select the "Network Services" from the Windows Components Wizard. Click the Details button and then
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 70
    Windows OS, the network camera can auto detect it via the "My Network Places". Under manual mode, you can modify external port. Under auto mode, select idle port for auto port MibBrowser 8.0c software or establish the SNMP service before you use this function. You need to reboot the device to activate
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 71
    -only access to all SNMP targets, default is public. Note: Only number, letter, _, and - supported. Read/write access to all SNMP targets, default is private. Note: Only number, letter, _, and - supported. The destination address of the Trap information from the proxy program of the device. Trap
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 72
    Figure 5-40 Check SNMP v3 version and SNMP port, read community, write community, Trap address, Trap port are same with SNMP v1 and SNMP v2 versions. Only when SNMP version is SNMP v3, users need to configure parameter in chart. Parameter Function SNMP Version Read-only Username Read/Write
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 73
    the Bonjour service in the same LAN to search the network camera device and then access if you do not know the network camera information such as IP address. You can view the server name when the network camera is detected by the Bonjour. Please note the safari browse support this function
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 74
    Figure 5-42 Please refer to the following sheet for detailed information. Parameter Function Enable Select to enable multicast function. Main stream and sub stream cannot be used at the same time. Multicast address Main/sub stream multicast default address is 224.1.2.4 and its range is 224
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 75
    Figure 4-53 Parameter Wireless Net Type Enable Function Auto, WCDMA, FDD-LTE optional, you can select according to the operator. Check to enable 4G module. APN It shall be acquired from the operator according to the setup of operator. Authentication Mode Auto, PAP and CHAP, the authentication
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 76
    calling list to call the SIM card inside the device to enable dial-up function. 5.2.12 WIFI Note: Some series devices don't support WIFI and WPS function. WPS function is supported by the devices with WPS button. 5.2.12.1 WIFI WIFI info can show the name, status, IP information of the Current Hot
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 77
    WIFI setting method is as follows: Step 1 Figure 5-45 Click , show as ，means enabling WIFI function. Step 2 Click " Search SSID", and shows the wireless network hot spot of the current network camera environment in the list. Figure 5-46 72
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 78
    3 Click "Add SSID" when need to add a wireless network manually，pop out an interface in the figure below, and enter network ID 802.1x 802.1x (port based network access control protocol) supports manual selection of authentication method to control if device connected to LAN can join the LAN. It well
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 79
    QoS interface is shown as below. See Figure 5-50. Qos (Quality of Service) is network security mechanism. It is a technology to fix the network delay and jam problem and etc. For the network service, the quality of service includes the transmission bandwidth, delay, the packet loss and etc. We can
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 80
    sheet for detailed information. Parameter Function Real-time monitor The value ranges from 0 to 63. The router or the switcher can provide different service for various data packets. Command Enable Wireless QoS The value ranges from 0 to 63. The router or the switcher can provide different
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 81
    Figure 5-51 2. Click "Create" and it will pop out the dialog box of "HTTPs", which is shown in Figure 5-52. Figure 5-52 3. Fill in corresponding "Country", "Province" and some other information, click "Create" after filling in. It will show the prompt of "Create Successfully", which means the server
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 82
    Note: Make sure the "IP or domain name" is the same as that of the device. 4. Click "Install" and it will install the certificate on the device end, which is shown in Figure 5-53. Figure 5-53 5. Click "Download". It will pop out the dialog box of "Save as", save the file into the computer. 77
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 83
    Figure 5-54 6. Double click the downloaded icon of "RootCert.cer". The system will display the information interface of "Certificate", which is shown in Figure 5-55. 78
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 84
    Figure 5-55 7. Click "Install Certificate" and it will pop out the interface of "Certificate Import Wizard", which is shown in Figure 5-56. 79
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 85
    Figure 5-56 8. Click "Next". Select "Trusted Root Certification Authorities", which is shown in Figure 5-57. 80
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 86
    Figure 5-57 9. Click "Next". The system will display the interface of "Completing the Certificate Import Wizard", which is shown in Figure 5-58. 81
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 87
    Figure 5-58 10. Click "Finish", and it will pop out the dialog box of "Security Warning", which is shown in Figure 5-59. 82
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 88
    Figure 5-59 11. Click "Yes". It will pop out the dialog box of "Import Successful", click "Ok" to complete downloading certificate, which is shown in Figure 5-60. Figure 5-60  Please refer to the following steps if you select "Install Signed Certificate". 1. Select "Setup > Network > HTTPs". The
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 89
    Figure 5-61 2. Select signed certificate and certificate key path respectively via "Browse", click "Upload". 3. Install root certificate, please refer to step 6~11 for more details. 4. Check "Enable HTTPs", click "Save". The system will display the dialog box of "Need to reboot the device", and then
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 90
    Figure 5-63 Note: "xx.xx.xx.xx" is corresponding to your IP or domain name. 5.3 Event 5.3.1 Video detection 5.3.1.1 Motion Detection Step 1 Select "Setup > Event > Video Detection > Motion Detection' and the system will display the interface of "Motion Detection" which is shown in Figure 5-64. 85
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 91
    Figure 5-64 Step 2 Select "Enable" to enable motion detection function. Step 3 Set motion detection area. 1. Click "Setup" and the system will pop out the interface of "Setting Area", which is shown in Figure 5- 65 86
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 92
    Figure 5-65 2. Set area name, it is to set valid area of motion detection according to the actual situation, and it can set the value of sensitivity and threshold respectively. The bigger the sensitivity is, the easier it is to generate motion detection, the smaller the threshold is, the easier it
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 93
    Parameter Working Period Anti-dither Area Record Record Delay Relay out Alarm Delay Send Email Audio linkage Function Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click "Setup" and the system will pop out the interface of "
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 94
    Parameter Flash linkage PTZ Snapshot Function Check it and the flash will be on when alarm occurs, and the flash will be off until the end of alarm after corresponding delay.  Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm.  The event type includes:
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 95
    Parameter Working Period Record Record Delay Relay out Alarm Delay Send Email Audio linkage Flash linkage PTZ Snapshot Function Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click "Setup" and the system will pop out the interface
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 96
    Figure 5-67 Step 2 Check "Enable" to enable the function of scene changing. Step 3 It is to set the parameters of scene changing, please refer to the following sheet for more details. Parameter Working Period Record Record Delay Function Note: It is to set the alarm period, it can enable alarm
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 97
    Parameter PTZ Snapshot Function  Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm.  The event type includes: preset, tour and pattern. You need to check the box here so that system can backup motion detection snapshot file. You shall set snapshot
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 98
    Parameter Sensitivity Threshold Working Period Anti-dither Record Record Delay Relay out Alarm Delay Send Email PTZ Snapshot Function It can be judged as audio abnormity when the input volume change exceeds continuous environment volume; users need to adjust according to the actual environment test
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 99
    5.3.3 Smart Plan Smart plan is the master switch for intelligent analysis such as "Face Detection", "Heat Map", "IVS", "People Counting" and so on, the corresponding intelligent functions can be valid after smart plan is enabled. Step 1 Select "Setup > Event > Smart Plan". The system will display
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 100
    5.3.4.1 IVS 5.3.4.1.1 Tripwire It will trigger alarm when the target crosses the warning line according to the movement direction which has been set. It needs some time from when the target appears to when the target is confirmed, so it has to leave some space on both sides of the warning line when
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 101
    Send Email Snapshot Function Select "Object tracking" to enable the function, refer to "2.4 Video Window Adjustment" for more details. Note: The function is only supported by some models. Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 102
     Cross means that it will trigger alarm when the target enters or exits the area.  Appears means that it will trigger alarm when the target appears in the area.  As for the report interval of the IVS function in the area, the system will trigger an alarm if it detects same event happened during
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 103
    Send Email Snapshot Function Select "Object tracking" to enable the function, refer to "2.4 Video Window Adjustment" for more details. Note: The function is only supported by some models. Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 104
    5.3.4.3 Abandoned Object Abandoned object means the system will trigger alarm if the abandoned object in the monitoring scene exceeds the time which has been set by the users. Abandoned object and missing object can be confusing in a situation where both foreground and background are complicated. It
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 105
    It is to set the parameter of abandoned object, please refer to the following sheet for more details. Parameter Working Period Keep time Record Record Delay Relay out Alarm Delay Send Email Snapshot Function Note: It is to set the alarm period, it can enable alarm event only during the period
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 106
    Application scene: it can be applied to the scene where the target is sparse and there is no obvious and frequent light change. False alarm will be increased in the scene where the target density is high and there is frequent obstruction; the false alarm will be increased in the scene where there
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 107
    Parameter Working Period Keep time Record Record Delay Relay out Alarm Delay Send Email Snapshot Function Note: It is to set the alarm period, it can enable alarm event only during the period range which has been set. 1. Click "Setup" and the system will pop out the interface of "Working Period".
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 108
    Figure 5-74 Step 2 Select "Enable" to enable face detection function. Step 3 Click "Draw Target" to draw the size model of target filter in the video image. Step 4 It is to set the parameters of face detection, please refer to the following sheet for more details. Parameter Working Period Enable
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 109
    Parameter Relay out Alarm Delay Send Email Snapshot Function Enable alarm activation function. You need to select alarm output port so that system can activate corresponding alarm device when alarm occurs. System can delay the alarm output for specified time after alarm ended. If you enabled this
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 110
    Click "Draw Target" to draw the size model of filtered target in the video image. Step 5 It is to set the parameters of entrance and exit, please refer to the following sheet for more details. Parameter Function Enable OSD Working Period Installation Mode Select "Enable OSD" and it will display
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 111
    It is to generate a form of report according to the number statistics. Step 1 Select "Setup > Event > People Counting > Report "and the system will display the interface of "Report', which is shown in Figure 5-76. Figure 5-76 Step 2 It is to set search condition, please refer to the following sheet
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 112
    Select "Setup > Event > Heat Map > Heat Map" and the system will display the interface of "Heat Map", which is shown in Figure 5-77. Figure 5-77 Step 2 Select "Enable" to enable heat map function. Step 3 It is to set the working period. 1. Click "Setup" and the system will display the interface of "
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 113
    Figure 5-78 2. It is to set working period according to the following methods:  You can input time numerical value or press the left mouse button to drag on the setup interface to set.  There are six periods to be set every day, select the check box in front of the period, and then the period is
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 114
    and end time. Step 3 Click "Search" to complete report statistics, click "Export" to export the statistics report. 5.3.8 Alarm Please note some series products do not support this function. 5.3.2.1 PIR alarm The alarm activation interface PIR alarm is shown as in figure 5-80. 109
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 115
    Figure 5-80 Please refer to the following sheet for detailed information. Parameter Function Enable Working period Anti-dither Flash Flash Delay After enabled, relay activation will work. Check it and enable the PIR alarm.  This function becomes activated in the specified periods.  There are
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 116
    Parameter Relay out Alarm delay Send Email Function Enable alarm activation function. You need to select alarm output port so that system can activate corresponding alarm device when alarm occurs. System can delay the alarm output for specified time after alarm ended. The value ranges from 10s to
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 117
    Parameter PTZ Function Check it and set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm. The event type includes: preset, tour and pattern and so on. 5.3.8.2 Flash Set Figure 5-82 Parameter ON/OFF Weak-strong bar All Period Function ON means flash is on; OFF means
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 118
    Figure 5-83 parameter Enable Threshold Function Check it and enable audio detection. It will trigger alarm and set up a series of linkage when volume exceeds the set threshold. 5.3.9 Abnormity Abnormity includes No SD Card, Capacity Warning, SD Card Error, Disconnection, IP Conflict and
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 119
    Figure 5-84 Figure 5-85 114
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 120
    Figure 5-86 Please refer to the following sheet for detailed information. Parameter Function Enable Check to alarm when SD card is abnormal. Relay-out Check to enable relay-out alarm. Relay out delay The alarm output can delay for the specified time after alarm stops. The value ranges from
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 121
    limit, user account will be locked. Figure 5-88 5.4 Storage Management 5.4.1 Schedule Before schedule setup, user must set record mode is auto or manual. Note: If record mode in record control is off, then device will not snapshot according to schedule. 5.4.1.1 Record Schedule Record schedule steps
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 122
    Figure 5-89 Step 2. From Monday to Sunday select record time, click on setup on the right, see Figure 5-90.  Set period according to actual need. There are six periods available each day.  By checking or unchecking, you can add or delete three types of record schedule: General, Motion, and Alarm.
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 123
    Figure 5-91 Step 4. In record schedule interface, click on OK. System prompts it is successfully saved. 5.4.1.2 Snapshot Schedule Snapshot setup as: Step 1. Click on Snapshot Schedule tab, see Figure 5-92. Figure 5-92 Step 2. From Monday to Sunday select snapshot time, click on setup on the right.
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 124
     By checking or unchecking, user can add or delete three types of snapshot schedule: General, Motion and Alarm. Note: Period setup can be done by dragging in snapshot schedule interface while not releasing left mouse. Figure 5-93 Step 3. Click on OK, return to snapshot schedule interface. See
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 125
    is corresponding to the three modes (general/motion/alarm) in the Schedule interface. Please check the box to enable the save functions. Note: Only device supports SD card has local. 120
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 126
    Figure 5-96 Please refer to the following sheet for detailed information. Parameter Function Event Type It includes: scheduled, motion detect and alarm. Local It saved in the SD card. FTP NAS It saved in the FTP server. It saved in NAS disk. 5.4.2.2 Local The local interface is shown as in
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 127
    You need to check the box to enable the FTP function. When network disconnect occurred or there is malfunction. Emergency storage can save the record/snapshot picture to the local SD card. Click the test button to check if the FTP server can be connected for test. Figure 5-98 5.4.2.4 NAS You need
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 128
    current HDD is full, it will stop record.  Overwrite: Current working HDD is full; it will overwrite the previous file. There are three modes: Auto/manual/close. There are two options: main stream and sub stream. 5.5 System 5.5.1 General The General interface is shown as in Figure 5-101. 123
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 129
    as PAL. Language You can select the language from the dropdown list. TV Out You can open or close the function, it can only be supported by the devices with TV Out.  Intelligent function will be disabled when TV Out is opened.  It will auto close TV Out when intelligent function
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 130
    Figure 5-102 Please refer to the following sheet for detailed information. Parameter Function Date format Here you can select date format from the dropdown list. Time Format Time zone Current Time There are two options: 24-H and 12-H. The time zone of the device. It is to set system time. It
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 131
    , hyphen, dot and @.  Password can be 0~32 characters in number and letter only. User can modify other user's password.  User and group can be manually added to 18 and 8 respectively.  User management adopts group/user modes. The user name and the group name shall be unique. One user shall be
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 132
    Figure 5-104 Modify user It is to modify the user property, belonging group, password and rights. See Figure 5-105. Modify password It is to modify the user password. You need to input the old password and then input the new password twice to confirm the new setup. Please click the OK button to save
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 133
    Figure 5-105 5.5.2.2 Group The group management interface can add/remove group, modify group password and etc. The interface is shown as in Figure 5-106. Figure 5-106 Add group: It is to add group and set its corresponding rights. See Figure 5-107. 128
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 134
    shown as in Figure 5-108. Here you can modify group information such as remarks and rights. Figure 5-108 5.5.3 PTZ Please note only some series products support this function. 129
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 135
    The PTZ settings interface is shown as in Figure 5-91. Figure 5-109 Please refer to the following sheet for detailed information. Parameter Function Protocol Address Baud Rate Select the corresponding dome protocol. Set corresponding dome address. Default value is 1. Please note your setup here
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 136
    import the local setup files to the system. It is to export the corresponding system setup to your local PC. 5.5.6 Remote control Note: It is supported by some devices. 131
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 137
    Figure 5-112 Parameter Learn Clear Arm/Disarm Function Bind remote control or wireless alarm with equipment. Unbind remote control with equipment. Start arm after the time you choose, disarm comes into effect immediately. Note: With disarm status, all the following alarms won't trigger: motion
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 138
    Parameter Function Auto Reboot Check it and set auto reboot time. Auto Delete Old Files Check it and set period within 1~31 days. 5.5.7 Upgrade The upgrade interface is shown as in Figure 5-114. Please select the upgrade file (file extension is ".bin") and then click the update button to begin
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 139
    select one item to view the detailed information. Clear You can click this button to delete all displayed log files. Please note system does not support clear by type. Backup You can click this button to backup log files to current PC. 5.6.3 Online User The online user interface is shown as
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 140
    Figure 5-117 135
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 141
    6 Alarm Please note some series product does not support this function. Click alarm function, you can see an interface is shown as in Figure 6-1. Here you can set device alarm type and alarm sound
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 142
    Type Operation Alarm Tone Parameter Prompt Play Alarm Tone Tone Path Function When alarm is triggered, there will be s inmain menu of alarm interface and system automatically records alarm info. The icon disappears when user click on alarm menu bar. Note: If alarm interface is displayed, when
  • IC Realtime IPEL-E80F-IRW1 | Product Manual - Page 143
    7 Log out Click log out button, system goes back to log in interface. See Figure 7-1. Figure 7-1 Note:  This manual is for reference only. Slight difference may be found in user interface.  All the designs and software here are subject to change without prior written
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
i
Network Camera Web3.0 Operation Manual
Version 1.0.1