Icom IC-7100 Instruction Manual - Page 30

The External Units Connections to a Transceiver, CAUTION: DO - software

Get Icom IC-7100 PDF manuals and user guides View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

2 INSTALLATION AND CONNECTIONS The External Units Connections to a Transceiver [DATA1] DATA1 JACK For GPS operation (AI sec. 10) • Connect a GPS receiver to the transceiv- er. • T he optional OPC-1529R (Data commu- nication cable) and a 3rd party's GPS receiver with RS-232C Port are required. OPC-1529R (Optional) For low-speed data communication in the DV mode (AI sec. 9) • Connect the transceiver to a PC. • T he USB cable can also be used for low-speed data commu- nication.. [TUNER] TUNER CONTROL SOCKET (AI sec.16) Connect the control cable from an optional AH-4 (HF/50 MHz automatic antenna tuner). AH-4 (Optional) AH-2b (Optional) • Connected to AH-4 [SP] (EXTERNAL) SPEAKER JACK (p. 2-4) Similar to the [PHONES/SP] jack on the controller. Plug in an external speaker. 3.5(d) mm/1⁄8˝ plug [DATA2] DATA2 SOCKET (AI sec. 18) Connect a TNC (Terminal Node Controller) for packet communication. [ACC] ACCESSORY SOCKET (p. 1-16) Connect control lines for external equipment such as TNC or a PC. [USB] USB (Universal Serial Bus) PORT [REMOTE] REMOTE CONTROL JACK • R emotely control the transceiver using CI-V commands (AI sec. 20) • Send the received audio to the PC • Input modulation (pp. 1-15, 6-8) • Send the decoded RTTY outputs to the PC • Low-speed data communication in the DV mode (AI sec. 9) • C loning using the optional CS-7100 cloning software (AI sec. 19) • Remotely control using the optional RS-BA1 • Remotely control the transceiver using CI-V commands. (AI sec. 20) • Cloning between transceivers (AI sec.19) 3.5(d) mm/1⁄8˝ plug NOTE: By setting "ACC/USB output selection" of the Connectors Set mode (AI sec. 17), the receiving tone can normally be output from the [ACC] socket, and the [USB] port can output an IF signal (12 kHz). This is required for the Software-Defined Radio (SDR) operation. The Digital Radio Mondiale (DRM) broadcast can be received using SDR. CAUTION: DO NOT connect any device to [REMOTE] when cloning using the optional CS-7100 cloning software. 2-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
2
INSTALLATION AND CONNECTIONS
2-6
The External Units Connections to a Transceiver
[DATA1] DATA1 JACK
For GPS operation (
AI sec. 10
)
• Connect a GPS receiver to the transceiv
-
er.
• The optional OPC-1529R (Data commu
-
nication cable) and a 3rd party's GPS re-
ceiver with RS-232C Port are required.
For low-speed data communication in the DV mode
(
AI sec. 9
)
• Connect the transceiver to a PC.
• The USB cable can also be used for low-speed data commu
-
nication..
OPC-1529R
(Optional)
[TUNER] TUNER CONTROL SOCKET (AI
sec.16)
Connect the control
cable from an op-
tional AH-4 (HF/50
MHz automatic an-
tenna tuner).
AH-4
(Optional)
AH-2b
(Optional)
•
Connected to AH-4
[SP] (EXTERNAL) SPEAKER JACK
(p. 2-4)
Similar to the [PHONES/SP] jack
on the controller. Plug in an exter-
nal speaker.
3.5(d) mm/
1
⁄
8
˝ plug
[USB] USB (Universal Serial Bus) PORT
•
Remotely control the transceiver using CI-V commands
(AI sec. 20)
•
Send the received audio to the PC
•
Input modulation (pp. 1-15, 6-8)
•
Send the decoded RTTY outputs to the PC
• Low-speed data communication in the DV mode (AI sec. 9)
•
Cloning using the optional CS-7100
CLONING
SOFTWARE
(
AI sec. 19
)
•
Remotely control using the optional RS-BA1
[DATA2]
DATA2 SOCKET
(
AI sec. 18)
Connect a TNC (Terminal Node Con-
troller) for packet communication.
[ACC] ACCESSORY
SOCKET (p. 1-16)
Connect control lines
for external equipment
such as TNC or a PC.
NOTE:
By setting “ACC/USB output selection” of the
Connectors Set mode (AI sec. 17), the receiving tone
can normally be output from the [ACC] socket, and
the [USB] port can output an IF signal (12 kHz). This
is required for the Software-Defined Radio (SDR) op-
eration. The Digital Radio Mondiale (DRM) broadcast
can be received using SDR.
CAUTION: DO NOT
connect any device to [RE-
MOTE] when cloning using the optional CS-7100
CLONING
SOFTWARE
.
[REMOTE] REMOTE CONTROL JACK
• Remotely control the transceiver using CI-V commands.
(AI sec. 20)
•
Cloning between transceivers (AI sec.19)
3.5(d) mm/
1
⁄
8
˝ plug