Icom IC-7100 Instruction Manual - Page 67

About “UR?” and “RPT?” error messages, ◇ Shows “UR?”, ◇ Shows “RPT?” or “RX”

Get Icom IC-7100 PDF manuals and user guides View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

5 D-STAR OPERATION About "UR?" and "RPT?" error messages The transceiver includes a status message in the signal received back from the access repeater, after transmitting. DDShows "UR?" The call was successfully sent, but no station's signal was received within 3 seconds. The called station may have missed your call, so after waiting for a while, try calling again. This means that your local area call was correctly sent from the "Hirano" repeater. DDShows "RPT?" or "RX" The destination repeater was not found, there is a programming error, or the destination repeater was busy. When "RPT?" is displayed, after waiting for a while, try calling again, because in a gateway call, your signal is sent even if the destination repeater is busy. NOTE: "RPT?" or "RX" is displayed when: • The repeater call sign programming is in error. • Y our own call sign is not registered on a gateway re- peater, or the registration contents is not matched. • T he destination call sign is not registered on a gateway repeater, or the registration contents is not matched. • T he destination repeater call sign is not registered on a gateway repeater, or the registration contents is not matched. • The destination repeater cannot be accessed. • A blank MY call sign memory is selected. ("RX" is displayed) DDShows "L" While operating in the voice communication or lowspeed data communication mode through the internet, some packets may be lost due to network error, or the caller's signal is weak getting into the repeater. In such a case, "L" is displayed to indicate that Packet Loss has occurred. When the transceiver receives corrupted data, and misidentifies it as Packet Loss, "L" is displayed, even if it is a Local area call. 5-5 This means that your gateway call was correctly sent from the "Hirano" repeater to the "Hamacho" repeater. This means that your gateway call was sent from the "Hirano" repeater to the "Hamacho" repeater, but the "Hamacho" repeater was busy at the time. Indicates packet loss "L" blinks while packet loss is occurring.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
5
D-STAR OPERATION <BASIC>
5-5
The transceiver includes a status message in the signal
received back from the access repeater, after transmit-
ting.
Shows “UR?”
D
The call was successfully sent, but no station’s signal
was received within 3 seconds.
The called station may have missed your call, so after
waiting for a while, try calling again.
Shows “RPT?” or “RX”
D
The destination repeater was not found, there is a pro-
gramming error, or the destination repeater was busy.
When “RPT?” is displayed, after waiting for a while, try
calling again, because in a gateway call, your signal is
sent even if the destination repeater is busy.
NOTE:
“RPT?” or “RX” is displayed when:
• The repeater call sign programming is in error.
• Your own call sign is not registered on a gateway re
-
peater, or the registration contents is not matched.
• The destination call sign is not registered on a
gateway repeater, or the registration contents is not
matched.
• The destination repeater call sign is not registered
on a gateway repeater, or the registration contents
is not matched.
• The destination repeater cannot be accessed.
• A blank MY call sign memory is selected. (“RX” is
displayed)
Shows “L”
D
While operating in the voice communication or low-
speed data communication mode through the internet,
some packets may be lost due to network error, or the
caller’s signal is weak getting into the repeater. In such
a case, “
L
” is displayed to indicate that Packet Loss has
occurred.
When the transceiver receives corrupted data, and
misidentifies it as Packet Loss, “
L
” is displayed, even
if it is a Local area call.
Indicates packet loss
“
L
” blinks
while packet
loss is occurring.
This means that your local area call was cor-
rectly sent from the “Hirano” repeater.
This means that your gateway call was correctly
sent from the “Hirano” repeater to the “Hama-
cho” repeater.
This means that your gateway call was sent
from the “Hirano” repeater to the “Hamacho” re-
peater, but the “Hamacho” repeater was busy
at the time.
About “UR?” and “RPT?” error messages