Icom IC-7100 Advanced Instructions - Page 357
While operating D-STAR
View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 357 highlights
Previous view 19 MAINTENANCE Troubleshooting DDWhile operating D-STAR PROBLEM POSSIBLE CAUSE SOLUTION REF. After your call, the repeat- • The access repeater setting is wrong. • Select the correct repeater. Sec. 8 er does not return a status • The repeater setting is wrong. • Correct the repeater frequency, frequency Sec. 9 reply. offset, or duplex setting. • Y our transmission did not reach the re- • W ait until you are closer to the repeater - peater. and try again. After your call, the repeat- • T he call was successfully sent, but no sta- • Wait for a while, and try again. er replies 'UR?' and its call tion immediately replied. sign. Sec. 8 After your call, the repeat- • Y our own call sign (MY) has not been set. • Set your own call sign (MY). Sec. 7 er replies 'RX' or 'RPT?' • Y our own call sign (MY) has not been reg- • Register your own call sign (MY) on a Sec. 7 and the access repeater's istered on a gateway repeater, or the reg- gateway repeater, or confirm the registra- call sign. istered contents do not match your trans- tion of the call sign. ceiver's setting. After your call, the repeat- • T he repeater cannot connect to the desti- • Check the repeater setting. er replies 'RPT?' and call nation repeater. sign of the destination re- • T he repeater is busy. • W ait for a while, and try it again. peater. Sec. 8 - After your call, the access • T he call sign of the destination repeater • Correctly set the destination repeater call Sec. 9 repeater replies 'RPT?' is wrong. sign. and its call sign. Even holding down DR , • There is no repeater list in your radio. • Reload the repeater list using the CS- Sec. 19 the DR mode will not appear. 7100 cloning software on the CD. • Reload the repeater list using an SD card. Sec. 13, 19 • Enter the Repeater list data directly into Sec. 9 the transceiver. Even holding down • T he call sign has not been correctly re- • T ry it again, after the transceiver has cor- - AUTO TUNE RX�CS , the received ceived. rectly received the call sign. call sign will not set to the • W hen a received signal is weak, or a sig- destination call sign. nal is received during scanning, the call sign may not be received correctly. In that case appears and error beeps sound, and a reply call cannot be made. A Local area call can be • M Y call sign has not been registered on a • Register your own call sign (MY) on a Sec. 7 made, but a Gateway call D-STAR repeater. gateway repeater, or confirm the registra- or destination station call tion of the call sign. cannot be made. During transmission, "L" • W hile receiving through the internet, some • Wait a while, and try it again. Sec. 9 appears on the LCD, and packets may be lost due to network error When the transceiver receives corrupted the received audio is inter- (poor data throughput performance). data, and misidentifies it is as Packet rupted. Loss, "L" is displayed, even if it is a Local area call. "DV" and "FM" icons alter- • W hile in the DV mode, an FM signal is • Use a different operating frequency until Sec. 9 nately blink. received. there are no FM signals on the original frequency. Simplex operation cannot • A call sign is programmed in "CALL SIGN" • Delete the Call sign in "CALL SIGN" set- Sec. 9 be made in the DR mode. of the Repeater list. ting of the Repeater list. • Duplex mode (DUP+, DUP-) is set. • Select "OFF" in "DUP" setting of the re- Sec. 9 peater list. • A repeater frequency is programmed. • Enter a simplex frequency. Sec. 9 The digital code squelch • The wrong digital code is set. (CSQL) is impossible. • Set the correct digital code. Sec. 9 You don't know how to up- - date the repeater list. • See "Updating the repeater list." Sec. 13 19-14