Icom IC-7100 Advanced Instructions - Page 360
Command table, Remote jack CI-V information Continued - command to read frequency
View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 360 highlights
Previous view 20 CONTROL COMMAND Remote jack (CI-V) information (Continued) DDCommand table Cmd. 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E Sub cmd. 00 01 A0 B0 A0 00 01 02 03 12 13 22 23 24 A1 A2 A3 A4 A5 A6 A7 B0 B1 D0 D3 Data Description see p. 20-11 Send the operating frequency for transceive see p. 20-11 Send the operating mode for transceive see p. 20-12 Read the band edge frequencies see p. 20-11 Read the operating frequency see p. 20-11 Read the operating mode see p. 20-11 Send the operating frequency 00 Select the LSB mode 01 Select the USB mode 02 Select the AM mode 03 Select the CW mode 04 Select the RTTY mode 05 Select the FM mode 06 Select the WFM mode 07 Select the CW-R mode 08 Select the RTTY-R mode 17 Select the DV mode Select the VFO mode Select VFO A Select VFO B Equalize VFO A and VFO B Exchange VFO A and VFO B Select the Memory mode 0001 to Select the Memory channel 0109 (0001=M-CH01 to 0099=M-CH99, 0100=1A, 0101=1B, 0102=2A, 0103=2B, 0104=3A, 0105=3B, 0106=144-C1, 0107=144-C2, 0108=430-C1, 0109=430-C2) 01 Select Memory Bank A 02 Select Memory Bank B 03 Select Memory Bank C 04 Select Memory Bank D 05 Select Memory Bank E Memory write Memory copy to VFO Memory clear Read offset frequency Send offset frequency Scan stop Programmed/memory scan start Programmed scan start ∂F scan start Fine programmed scan start Fine ∂F scan start Memory scan start Select memory scan start Mode select scan start Set the ±5 kHz ∂F scan span Set the ±10 kHz ∂F scan span Set the ±20 kHz ∂F scan span Set the ±50 kHz ∂F scan span Set the ±100 kHz ∂F scan span Set the ±500 kHz ∂F scan span Set the ±1 MHz ∂F scan span Set as the Non-select Memory channel Set as the Select Memory channel Set Scan resume function OFF Set Scan resume function ON Cmd. Sub cmd. 0F 00 01 10 11 12 10 11 13 00 01 02 14 01 02 03 06 07 08 09 0A 0B 0C 0D 20-3 Data 00 01 11 12 00 01 02 03 04 05 06 07 08 09 10 11 12 00 12 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 0000 to 0255 Description Read Split function OFF Read Split function ON Read DUP- operation Read DUP+ operation Set Split function OFF Set Split function ON Set the simplex operation Set DUP- operation Set DUP+ operation Send/read the 10 Hz (1 Hz) tuning step Send/read the 0.1 kHz tuning step Send/read the 1 kHz tuning step Send/read the 5 kHz tuning step Send/read the 6.25 kHz tuning step Send/read the 9 kHz tuning step Send/read the 10 kHz tuning step Send/read the 12.5 kHz tuning step Send/read the 20 kHz tuning step Send/read the 25 kHz tuning step Send/read the 50 kHz tuning step Send/read the 100 kHz tuning step Send/read the 1 MHz tuning step Send/read Attenuator OFF Send/read 12 dB attenuator Announce the operating frequency, operating mode and S-meter level by voice synthesizer Announce the operating frequency and S meter level by voice synthesizer Announce the operating mode by voice synthesizer Send/read the AF level (0000=min. to 0255=max.) Send/read the RF gain level (0000=min., 0255=max.) Send/read the squelch level (0000=min. to 0255=max.) Send/read the NR level (0000=0% to 0255=100%) Send/read the inner [TWIN PBT] position (0000=Cutting the higher passband edge, 0128=center, 0255=Cutting the lower passband edge) Send/read the outer [TWIN PBT] position (0000=Cutting the higher passband edge, 0128=center, 0255=Cutting the lower passband edge) Send/read the CW PITCH (0000=300 Hz, 0128=600 Hz, 0255=900 Hz) Send/read the RF power level (0000=min. to 0255=max.) Send/read the MIC gain level (0000=min. to 0255=max.) Send/read the KEY SPEED (0000=6 WPM to 0255=48 WPM) Send/read the NOTCH setting (0000=lowest, 0128=center, 0255=highest)