Icom IC-7100 Advanced Instructions - Page 369
Character code setting, Character, Freq. band, Frequency range unit: MHz, Registered No.
View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 369 highlights
Previous view 20 CONTROL COMMAND Remote jack (CI-V) information DDData content description (Continued) • C haracter code setting Command: 1A 00, 1A 05 0200, 1A 05 0201, 1A 05 0206, 1A 05 0207, 1A 05 0208, 1A 05 0209, 1A 05 0211, 1F 02, 20 0001, 20 0002 Character ASCII code Character ASCII code A-Z 41-5A a-z 61-7A 0-9 30-39 Space 20 ! 21 # 23 $ 24 % 25 & 26 \ 5C ? 3F " 22 ' 27 ` 60 ^ 5E + 2B - 2D ✱ 2A ⁄ 2F . 2E , 2C : 3A ; 3B = 3D < 3C > 3E ( 28 ) 29 [ 5B ] 5D { 7B } 7D ¦ 7C _ 5F ¯ 7E @ 40 • Band edge frequency setting Command 02*, 1E 01, 1E 03 q w e r t y u i o !0 !1 !2 XXXXXXXXXXXX 2 DXXXXXXXXXX • Band stacking register Command : 1A 01 q w XXXX When sending the contents, the codes, such as operating frequency and operating mode*, should be added after the frequency band code and register code, as shown below. *See t to %1 on 'Memory content setting.' (p. 20-16) qqFrequency band code Code Freq. band Frequency range (unit: MHz) 01 1.8 1.800000- 1.999999 02 3.5 3.400000- 4.099999 03 7 6.900000- 7.499999 04 10 9.900000-10.499999 05 14 13.900000-14.499999 06 18 17.900000-18.499999 07 21 20.900000-21.499999 08 24 24.400000-25.099999 09 28 28.000000-29.999999 10 50 50.000000-54.000000 11 144 144.000000-148.000000 12 430 420.000000-450.000000 13 GENE Other than above wwRegister code Code Registered No. 01 1 (latest) 02 2 03 3 (oldest) To read the contents, the register code should be added after the frequency band code, as shown below. Example: W hen reading the oldest contents in the 21 MHz band, the code "0703" is used. Edge number*: 01-30 10 Hz digit: 0-9 1 Hz digit: 0-9 1 kHz digit: 0-9 100 Hz digit: 0-9 100 kHz digit: 0-9 10 kHz digit: 0-9 10 MHz digit: 0-9 1 MHz digit: 0-9 1000 MHz digit: 0 (fixed) 100 MHz digit: 0-9 Separator (fixed) 10 Hz digit: 0-9 1 Hz digit: 0-9 1 kHz digit: 0-9 100 Hz digit: 0-9 100 kHz digit: 0-9 10 kHz digit: 0-9 10 MHz digit: 0-9 1 MHz digit: 0-9 1000 MHz digit: 0 (fixed) 100 MHz digit: 0-9 Lower edge Higher edge * Edge number (q) is not sent with command 02 (reading the band edge frequencies). 20-12