Icom IC-7100 Advanced Instructions - Page 373
About clearing operation, A, 02: B, 03: C, 04: D, 05: E
View all Icom IC-7100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 373 highlights
Previous view 20 CONTROL COMMAND Remote jack (CI-V) information DDData content description (Continued) • Memory content setting Command: 1A 00 q wɺe r tʙo !0ɺ!1 !2 !3 !4 !ʙ5 !7 !ʙ8 @0 @ʙ1 @3 @4 @ʙ5 @7 9 9 9 9 9 9 9 9 9 9 ʜʜ 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 @ʙ8 #5 #ʙ6 $3 $ʙ4 %1 tʙ%1 %ʙ2 ^0 9 9 ʜʜ 9 9 9 9 ʜʜ 9 9 9 9 ʜʜ 9 9 9 9 ʜʜ 9 9 qqBank number 01: A, 02: B, 03: C, 04: D, 05: E !4 Digital squelch setting !4 w, e Memory channel number 0001-0099: Memory channel 1 to 99 0100: Programmed scan edge 1A 0101: Programmed scan edge 1b 0102: Programmed scan edge 2A 0103: Programmed scan edge 2b 0104: Programmed scan edge 3A 0105: Programmed scan edge 3b 0106: Call channel 144-C1 0107: Call channel 144-C2 0108: Call channel 430-C1 0109: Call channel 430-C2 rrSplit and Select memory settings r XX 0: Select memory OFF 1: Select memory ON 0: Split OFF, 1: Split ON When the program channel is selected, both settings should be "0." When the Call channel is selected, the Select memory setting should be "0." X0 0: Digital squelch function OFF 1: Digital call sign squelch function ON (DSQL) 2: Digital code squelch function ON (CSQL) !5-!7 Repeater tone frequency setting !8-@0 Tone squelch frequency setting See '• Repeater tone/tone squelch frequency setting.' (p. 20-14) @1-@3 DTCS code setting See '• DTCS code and polarity setting.' (p. 20-14) @4 Digital code squelch setting See '• Digital code squelch setting.' (p. 20-14) @5-@7 Duplex offset frequency setting See '• Duplex Offset frequency setting.' (p. 20-13) @8-#5 Destination call sign setting (8 characters; fixed) #6-$3 R1 (Access repeater) call sign setting (8 characters; fixed) $4-%1 R2 (Gateway/Link repeater) call sign setting (8 characters; fixed) See '• DV TX call signs setting.' (p. 20-14) t-o Operating frequency setting See '• Operating frequency.' (p. 20-11) !0, !1 Operating mode setting See '• Operating mode.' (p. 20-11) !2 Data mode setting 1 byte data (XX) 00: Data mode OFF 01: Data mode ON !3 Duplex and Tone settings !3 XX 0: OFF, 1: Tone 2: TSQL, 3: DTCS 0: Duplex OFF 1: Duplex−, 2: Duplex+ %2-^7 Memory name setting 16 characters (Fixed) See '• Character code setting.' (p. 20-12) About clearing operation: "1A 00" command with the format as below clears the data of the selected memory channel. w, e : Memory channel 0 to 99 r : FF t or later : None NOTE: • The same data as t-%1 are stored in t-%1. • W hen the Split function is ON, the data of t-%1 is used for transmit. • Even if the Split function is OFF, enter the data into t-%1 to match your transceiver. We recommend that you set the same data as t-%1. 20-16