Icom IC-A14S Instruction Manual

Icom IC-A14S Manual

Get Icom IC-A14S PDF manuals and user guides View all Icom IC-A14S manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-A14S manual content summary:

  • Icom IC-A14S | Instruction Manual - Page 1
    INSTRUCTION MANUAL VHF AIR BAND TRANSCEIVER iA14 iA14S This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. YIC-A14 YIC-A14S
  • Icom IC-A14S | Instruction Manual - Page 2
    product. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure.; Belt Clip (MB-94/96F) and Rechargeable Li-ion Battery Pack (BP-230N/ 232N). • D O NOT operate the radio without a proper antenna attached, as this
  • Icom IC-A14S | Instruction Manual - Page 3
    MANUAL- This in- struction manual contains important operating instructions for the IC-A14/S. Supplied Accessories The following accessories are supplied with the transceiver.  Qty. q Flexible antenna 1 w Battery pack 1 e Belt clip 1 r Hand strap 1 t Battery charger 1 y AC adapter
  • Icom IC-A14S | Instruction Manual - Page 4
    use of non-Icom battery packs/chargers to prevent the loss of the transceiver's good performance and warranty. DO NOT allow children to play with any radio equipment containing a transmitter. FCC caution: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void
  • Icom IC-A14S | Instruction Manual - Page 5
    with the IC-A14 only 23 n Duplex operation (Available with the IC-A14 only 24 n Set mode setting 25 7 BATTERY PACKS 27-31 n Battery charging 27 n Charging the battery 29 8 CLONING 32-33 9 TROUBLESHOOTING 34 10 SPECIFICATIONS 35 11 OPTIONS 36 12 OPTIONAL HEADSET CONNECTION 37 iv
  • Icom IC-A14S | Instruction Manual - Page 6
    [ANT] (p. 6) Connects the supplied antenna. w KEY LOCK SWITCH [ ] (p. 9)  Push to turning the key lock function ON.  Push and hold for 2 sec. to turning the key lock function OFF. e LIGHT SWITCH [LIGHT] Push to toggles the LCD backlight ON and OFF. (p. 11) For IC-A14S only During memory mode
  • Icom IC-A14S | Instruction Manual - Page 7
    KEYPAD (Available with the IC-A14 only; pgs. 3, 4) !0 EXTERNAL SPEAKER AND MICROPHONE JACKS 2 i MEMORY MODE/MEMORY WRITE KEY [MR]/[MW] Push to select memory mode. (p. 12) [MIC/SP] (p. 37) Connects the optional speaker microphone or a headset 3 using with the optional OPC-499 HEADSET ADAPTER
  • Icom IC-A14S | Instruction Manual - Page 8
    KEYPAD (Available with IC-A14 only)  Inputs digit "1" for frequency input or memory channel selection, etc. (pgs. 8, 12)  Inputs "1," "Q," or "Z" during memory name programming programming. (p. 15)  After pushing [FUNC], enters duplex transmit frequency programming condition, during NAVI band
  • Icom IC-A14S | Instruction Manual - Page 9
    . (p. 20)  Inputs digit "0" for frequency input or memory channel selection, etc. (pgs. 8, 12)  Inputs "0," "space" or "-" during memory name programming. (p. 15)  After pushing [FUNC], selects the emergency frequency, 121.500 MHz. (p. 21)  Completes the numeral input for frequency or memory
  • Icom IC-A14S | Instruction Manual - Page 10
    WEATHER ALERT INDICATOR (IC-A14 only) (p. 23) Appears when the weather alert function is in use. o LOCK INDICATOR (p. 9) A ppears when the lock function is in use. !0 LOW BATTERY INDICATOR (p. 11)  Appears when the battery is nearing exhaustion. The attached battery pack requires recharging when
  • Icom IC-A14S | Instruction Manual - Page 11
    . CAUTION! • N EVER carry the transceiver by the antenna. • DO NOT transmit without an antenna. Otherwise the transceiver may be damaged. 2 ACCESSORY ATTACHMENT D Belt clip 1 Conveniently attaches to your belt. Attach the belt clip as described below. 2 q Release the battery pack if it is
  • Icom IC-A14S | Instruction Manual - Page 12
    2 ACCESSORY ATTACHMENT D Battery pack attachment Turn the transceiver power OFF with [VOL] before attaching or detaching the battery pack. Slide the battery pack in the direction of the arrow (q), then lock it with the battery release button. • Slide the battery pack until the battery release
  • Icom IC-A14S | Instruction Manual - Page 13
    on the function display. w Push [Y]/[Z] to set the desired frequency. - For IC-A14 only • 1 MHz tuning step is available with the IC-A14; push [FUNC], then push [Y]/[Z]. Push [FUNC] again to return the normal tuning. D Using keypad (IC-A14 only) q Rotate [VOL] to turn power ON, then push [CLR] to
  • Icom IC-A14S | Instruction Manual - Page 14
    3 BASIC OPERATION n Setting a squelch level The transceiver has a noise squelch circuit to mute undesired noise while receiving no signal. q Push [SQLY] or [SQLZ] to select the squelch level. • 'SQL--0' is open squelch
  • Icom IC-A14S | Instruction Manual - Page 15
    keypad (IC-A14 only). • COM band frequency range: 118.00-136.975 MHz w Push and hold [PTT] to transmit. • " " indicator appears. e Speak into the microphone at a normal voice level. 3 4 5 6 y When a signal is received on the set frequency: • " " indicator appears. • DO NOT hold the transceiver
  • Icom IC-A14S | Instruction Manual - Page 16
    transceiver when using this function (OPC-499 HEADSET ADAPTER and headset are required). (p. 37) D Setting the side tone level q Push [PTT] to turn the transmit mode ON. w During transmit, push [Y]/[Z] to adjust the level. • 'ST--0' is OFF and 'ST--10' is maximum level. n LCD backlight The IC-A14
  • Icom IC-A14S | Instruction Manual - Page 17
    ) is displayed. propriate digit key ([0] to [9]) to enter 11 • If no memory CH is programmed, no memory CH selection is available. the desired memory 12 Using the Keypad- IC-A14 only: BANK number, then push [ENT]. 13 w Push 2 appropriate digit key (00 to 99, depending on r Push
  • Icom IC-A14S | Instruction Manual - Page 18
    4 MEMORY OPERATION n Programming a memory channel Program often-used frequencies with the following instructions. D For IC-A14 q Push [CLR] to select the frequency mode, if necessary. w Set the desired frequency. (p. 8) • P ush [FUNC], then push [WX](7) to select a weather channel mode, and then
  • Icom IC-A14S | Instruction Manual - Page 19
    OPERATION 4 1 2 3 D For IC-A14S q Push [CLR] to select the frequency mode, if necessary. • EXAMPLE: Programming 123.450 MHz into memory 4 w Set 1 sec. 12 t Push and hold [MR] for 1 sec. to program the set condition into the memory channel and return to the frequency mode. Push or
  • Icom IC-A14S | Instruction Manual - Page 20
    mode. (p. 8) w Enter the select memory write mode. • For IC-A14; push [FUNC] then push [MW](MR). • For IC-A14S; push and hold [MR] for 1 sec. e Select the desired memory channel to be programmed with [Y]/[Z] (or keypad and [ENT]; for IC-A14 only). r Push [MR] momentarily to enter the memory name
  • Icom IC-A14S | Instruction Manual - Page 21
    the desired memory channel to be transferred 5 using [Y]/[Z] (or keypad and [ENT]; for IC-A14 only). 6 • Select the desired bank if desired. • in "For IC-A14" to program the desired memory name. For IC-A14S e Push and hold [MR] for 1 sec. to copy the memory chan- 10 11 For IC-A14S w Push and
  • Icom IC-A14S | Instruction Manual - Page 22
    4 MEMORY OPERATION n Clearing the memory contents (Available with the IC-A14 only) Unwanted memory channels can be cleared. q Select the desired memory channel to be cleared. (p. 12) • Select the desired bank if desired. (p. 12) w Push [FUNC]
  • Icom IC-A14S | Instruction Manual - Page 23
    FUNC], then push [SCAN](2) to start the scan. 5 Scan Jump over the entire COM band. • When a signal is received, the scan pauses until it disappears. • To change the scanning direction, push [Y]/[Z]. 6 For IC-A14S 7 MEMORY SCAN non-TAG channel e Push and hold [Y]/[Z] for 1 sec. to start the
  • Icom IC-A14S | Instruction Manual - Page 24
    n Memory scan NOTE: Program 2 or more memory channels with "TAG" setting to start memory scan. q Push [MR] to select memory mode. • For IC-A14, select the desired BANK if desired. (p. 12) w P ush [SQLY]/[SQLZ] to set the squelch level to the point where noise is just muted. For IC-A14 e Push [FUNC
  • Icom IC-A14S | Instruction Manual - Page 25
    spectively. The "TAG" channel function is only available dur- w Select the desired memory channel to be a "TAG" chan- ing scan operation. *for IC-A14 only nel. 4 e Push and hold [LIGHT] for 2 sec. to set a "TAG." r To cancel the "TAG" setting, repeat the above steps. 5 6 7 " " indicator
  • Icom IC-A14S | Instruction Manual - Page 26
    to suits your preference using with the optional cloning software, CS-A14.  Push and hold [CLR] for 2 sec. to return the transceiver into the default setting. n Accessing 121.5 MHz emergency frequency (Available with the IC-A14 only) The IC-A14 can set to the 121.5 MHz emergency frequency
  • Icom IC-A14S | Instruction Manual - Page 27
    . 10 r Push [Y]/[Z] to select the desired condition from ON 11 and OFF. t Push [CLR] to return to frequency mode. For IC-A14S q Rotate [VOL] to turn the transceiver power OFF. 12 w While pushing and holding [Y]/[Z], rotate [VOL] to enter 13 set mode. e Push [MR] several times to select
  • Icom IC-A14S | Instruction Manual - Page 28
    FUNCTIONS n Weather channel operation (Available with the IC-A14 only) The IC-A14 has VHF marine WX (weather) channel receiving capability for flight function is turned ON, the transceiver detects the alert, and sounds a beep tone until the transceiver is operated. The previously selected
  • Icom IC-A14S | Instruction Manual - Page 29
    operation (Available with the IC-A14 only) 1 The duplex function allows you to call a flight service station 2 while receiving a VOR station. The duplex function requires 3 frequency programming for the flight service station in ad- vance. 4 D Programming a duplex frequency D Operating the
  • Icom IC-A14S | Instruction Manual - Page 30
    mode is used for programming infrequently changed values or conditions of functions. D Entering set mode q Rotate [VOL] to turn the transceiver power OFF. w software, CS-A14. And the default settings are re-called by the home function. D Set mode items • ANL- ANL function (available with IC-A14S
  • Icom IC-A14S | Instruction Manual - Page 31
    • I.MIC- Internal microphone usage The internal microphone can be deactivated for headset operation. This setting prevents unwanted audio/noise transmission entering from the internal microphone with [PTT] operation. • TOT- Time-out timer Sets the time-out timer
  • Icom IC-A14S | Instruction Manual - Page 32
    of Lithium-ion batteries may result in the following hazards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom charger. Only Icom battery
  • Icom IC-A14S | Instruction Manual - Page 33
    the transceiver) into the charger if it is wet or soiled. This 12 temperature environment (above +45˚C; +113˚F) for an ex- could corrode the battery charger terminals or damage the 13 tended period of time. If the battery must be left unused for a long time, it must be detached from the radio
  • Icom IC-A14S | Instruction Manual - Page 34
    regular charging of battery packs. The following are additionally required. • An AC adapter (may be supplied with the transceiver depending on versions) : The inserted battery pack or the charger has problem. Charging indicator Be sure to turn the transceiver power OFF, when charging
  • Icom IC-A14S | Instruction Manual - Page 35
    the DC power cable (OPC-515L). 4 q AD-106 Connectors w Screws (supplied with AD-106) 5 Transceiver Turn power OFF 6 AC adapter (Not supplied with Battery pack 7 some versions.) 8 9 10 AD-106 charger adapter is installed 11 in BC-119N. 12 Plugs Optional OPC-515L (for 13.8 V power
  • Icom IC-A14S | Instruction Manual - Page 36
    cable (OPC-656). Battery pack Transceiver Turn power OFF AC adapter (Purchased separately) AD-106 charger adapters are installed in each slot. DC power cable (OPC-656) (Connect with the DC power supply; 13.8 V/at least 7 A) IMPORTANT!: Ensure the guide lobes on the battery pack are correctly
  • Icom IC-A14S | Instruction Manual - Page 37
    transceiver to another transceiver, or, data from PC to a transceiver using the optional CS-A14 2 cloning software. 3 D Transceiver to transceiver again to exit cloning mode. 11 NOTE: Transceiver to transceiver cloning between 12 IC-A14 and IC-A14S cannot be performed. 13 14 w While
  • Icom IC-A14S | Instruction Manual - Page 38
    type) or OPC-478UC (USB type) CLONING CABLE. Consult the CS-A14 CLONING SOFTWARE HELP file for details. D Cloning error When the display as below appears, a cloning error has occurred. In this case, both transceivers automatically return to the clone standby condition and cloning must be repeated
  • Icom IC-A14S | Instruction Manual - Page 39
    9 TROUBLESHOOTING If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. 1 PROBLEM POSSIBLE CAUSE SOLUTION REF. 2 No power comes on. • The battery is exhausted. • Bad connection for the battery pack. • Recharge the battery
  • Icom IC-A14S | Instruction Manual - Page 40
    g (6.35 oz) (Without the battery pack and antenna.) • Receive system : Double conversion superhetero- dyne • Intermediate frequencies : 1st 46.35 MHz, 2nd 450 kHz • Sensitivity : COM band (6 dB S/N) -6 dBµ typical NAVI band (6 dB S/N) -3 dBµ typical (IC-A14 only) WX channels (12 dB
  • Icom IC-A14S | Instruction Manual - Page 41
    -232N (Li-ion). • BC-179 desktop charger + BC-174 ac adapter For regular charging of BP-230N and BP-232N (Li-ion). D MICROPHONE • HM-173 speaker microphone Combination speaker and microphone. • CS-A14 cloning software + OPC-478/UC cloning cable Provides quick and easy programming of items, such
  • Icom IC-A14S | Instruction Manual - Page 42
    a 3.5 mm (1⁄8˝) diameter plug, if required. OPC-499 HEADSET (Must be purchased separately) Transceiver NOTICE! Some headsets do not work properly when used with the IC-A14/S. Therefore, ask your dealer for details about headsets compatible for operation with the IC-A14/S with the headset. 37
  • Icom IC-A14S | Instruction Manual - Page 43
    MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 38
  • Icom IC-A14S | Instruction Manual - Page 44
    A-6631H-1EX Printed in Japan © 2007 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
INSTRUCTION MANUAL
iA14
iA14S
VHF AIR BAND TRANSCEIVER
This device complies with Part 15 of the FCC
Rules. Operation is subject to the condition
that this device does not cause harmful inter-
ference.
Y
IC-A14
Y
IC-A14S