Icom IC-F6123D Instruction Manual

Icom IC-F6123D Manual

Get Icom IC-F6123D PDF manuals and user guides View all Icom IC-F6123D manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IC-F6123D manual content summary:

  • Icom IC-F6123D | Instruction Manual - Page 1
    INSTRUCTION MANUAL VHF MOBILE TRANSCEIVERS iF5120D Series UHF MOBILE TRANSCEIVERS iF6120D Series
  • Icom IC-F6123D | Instruction Manual - Page 2
    INSTRUCTION MANUAL - This instruction manual contains important opera­ ting instructions for the IC-F5121D, IC-F5123D, IC-F5128D VHF MOBILE TRANSCEIVERS and the IC-F6121D, IC modifications to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver
  • Icom IC-F6123D | Instruction Manual - Page 3
    assignments and may damage the transceiver. CAUTION: NEVER expose the transceiver to rain, snow or any liquids. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New
  • Icom IC-F6123D | Instruction Manual - Page 4
    TABLE OF CONTENTS IMPORTANT i EXPLICIT DEFINITIONS i FCC INFORMATION i PRECAUTIONS ii 1 PANEL DESCRIPTION 1-7 ■ Front panel 1 ■ Function display 2 ■ Programmable function keys 3 2 BASIC OPERATION 8-14 ■ Turning ON the power 8 ■ Channel selection 8 ■ Call procedure 9 ■ Receiving and
  • Icom IC-F6123D | Instruction Manual - Page 5
    r 8 q AF VOLUME CONTROL KNOB [VOL] t MICROPHONE CONNECTOR 9 Rotate the knob to adjust the audio output level. • Minimum audio level is pre-programmed. (p. 12) w UP/DOWN KEYS [CH Up]/[CH Down] Connect the supplied or optional microphone. 10 N EVER connect non-specified microphones. The pin
  • Icom IC-F6123D | Instruction Manual - Page 6
    channel is selected. o ALPHANUMERIC DISPLAY Displays an operating channel number, channel name, User Set mode contents, DTMF code, etc. * Digital operation only See the operating guide for details of MDC and Digital system operations. Ask your dealer for details. 2
  • Icom IC-F6123D | Instruction Manual - Page 7
    P0], [P1], [P2] and [P3] programmable function keys. Consult your Icom dealer or system operator for details con- ➥ Push to start and cancel to display the scan group, 5 As described in the following topics, after pushing a programmed key, push [CH Up] or [CH Down] to select an option, setting,
  • Icom IC-F6123D | Instruction Manual - Page 8
    push to send a 'reset code' (only 5-tone operation). NOTE: The 'Audible' (unmute) mode may automatically return to the 'Inaudible' (mute) mode, after the pre-programmed time period. LIGHT KEY Push to turn ON the backlight for about 5 seconds, when the backlight function is set to "OFF" in the User
  • Icom IC-F6123D | Instruction Manual - Page 9
    passband width can be selected from 25.0 or 20.0 kHz to select a desired tone frequency/code setting. After the using the CS-F3100D/F5120D cloning software. (PMR operation selection, push this key again to set it. only) Ask your dealer for details. ➥ While in digital mode, push to enter the
  • Icom IC-F6123D | Instruction Manual - Page 10
    1 PANEL DESCRIPTION ■ Programmable function keys (Continued) CALL KEYS Push to transmit a 2/5-tone ID code. • Tone call transmission may be necessary before you call another station, depending on your signalling system. • [Call A] and/or [Call B] may be selectable when your system em- ploys
  • Icom IC-F6123D | Instruction Manual - Page 11
    SCAN control is connected to the transceiver with an optional OPC-1939 or OPC-2078 cable (p. 17). 7 When the Hook Scan function is pre-programmed, push this key to temporarily disable the function. Push this key again to • Ask your dealer for more details on external input operation. 8 enable
  • Icom IC-F6123D | Instruction Manual - Page 12
    2 BASIC OPERATION ■ Turning ON the power q Push [ ] to turn ON the power. w If the transceiver is programmed for a start up password, input the digit codes as directed by your dealer. • The keys shown below can be used for password input: The transceiver
  • Icom IC-F6123D | Instruction Manual - Page 13
    contacting you. put level to a comfortable listening level. 5 q S elect the desired TX code channel or 2/5-tone code, according to your System Operator's instructions. • This may not be necessary, depending on the preprogramming. • Refer to pages 10 and 11 for selection. NOTE: Depending on the
  • Icom IC-F6123D | Instruction Manual - Page 14
    transmission is cut off. • Penalty timer After the transmission is cut off by the time-out timer, transmission is further inhibited for the pre-programmed penalty timer period. • PTTID call The transceiver automatically sends the 5-tone, DTMF, BIIS or digital ANI ID code when [PTT] is pushed (at
  • Icom IC-F6123D | Instruction Manual - Page 15
    BASIC OPERATION 2 1 D TX code number edit (PMR operation only) If the transceiver has a key assigned to [TX Code CH Select] USING [TX CODE ENTER] KEY: 2 or [TX Code Enter], TX code contents can be edited within q Push [TX Code Enter] to enter the TX code edit mode. 3 the allowable digits.
  • Icom IC-F6123D | Instruction Manual - Page 16
    is necessary to operate the transceiver again in this case. * Depending on the preprogramming. Ask your dealer for de- tails. See the operating guide for details of the Stun function with the MDC and Digital system operations. Ask your dealer for details. ■ Encryption function The encryption
  • Icom IC-F6123D | Instruction Manual - Page 17
    If you want to cancel the Emergency function, hold down After the emergency call transmission, the transceiver stands [Emergency] for the pre-programmed time period again be- by in the audible mode for the specified time period.* fore transmitting the call. * Depending on the preprogramming
  • Icom IC-F6123D | Instruction Manual - Page 18
    are turned OFF as well. On the other hand, the transceiver can transmit emergency calls according to the pre-programmed emergency settings. Depending on the pre-programmed settings, the Remote Monitor function can also be used (digital operation only). To cancel the Power OFF Emergency function
  • Icom IC-F6123D | Instruction Manual - Page 19
    3 CONNECTION AND MAINTENANCE ■ Rear panel connection 1 Antenna q ANTENNA CONNECTOR e MICROPHONE HANGER 2 Connect to an antenna. Ask your dealer about antenna selection Connect the supplied microphone hanger to the vehicle's 3 and placement. ground for microphone ON/OFF 4 hook functions.
  • Icom IC-F6123D | Instruction Manual - Page 20
    supplied with your transceiver allows overhead mounting. • Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg (3.3 lb). Flat washer Flat washers Nuts Mounting screws (5×12) Spring washers Bracket bolts Self-tapping screws (5×20
  • Icom IC-F6123D | Instruction Manual - Page 21
    -pin 6 power cable*. If a fuse blows or the transceiver stops func- OPC-2078 : D-sub 25-pin 7 tioning, track down the source of the problem if possible, repair it and then replace the damaged fuse with a new rated NOTE: No Digital Modulation "IN" using accessory cables. 8 one. *Depending on
  • Icom IC-F6123D | Instruction Manual - Page 22
    4 SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic en- 3. IC-F5121D: ergy during transmit mode. the nearest edge of the vehicle in order to protect against exposure to bystanders. 2. IC-F6121D: T he antenna is required to be located outside of a vehicle and kept at
  • Icom IC-F6123D | Instruction Manual - Page 23
    on the LCD. You can cause the radio to transmit by pressing the "PTT" switch. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn OFF the radio in
  • Icom IC-F6123D | Instruction Manual - Page 24
    SAFETY TRAINING INFORMATION Votre radio Icom produit une énergie électro- 3. IC-F5121D: magnétique de radiofré plus rapproché du véhicule et ainsi éviter que les personnes présentes soient exposées. 2. IC-F6121D: Il faut que l'antenne émettrice de cet appareil soit placée à l'exté- rieur
  • Icom IC-F6123D | Instruction Manual - Page 25
    é 1 une énergie électromagnétique de RF se situe dans les limites permises par la FCC pour une En mode de transmission, votre radio Icom produit de l'énergie de RF qui peut provoquer des interférences avec d'autres appareils ou 2 utilisation grand public, veuillez en tout temps MISE EN
  • Icom IC-F6123D | Instruction Manual - Page 26
    MEMO 22
  • Icom IC-F6123D | Instruction Manual - Page 27
    MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 23
  • Icom IC-F6123D | Instruction Manual - Page 28
    A6903H-1EX-4 Printed in Japan © 2010-2018 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
INSTRUCTION MANUAL
VHF MOBILE TRANSCEIVERS
iF5120D
Series
UHF MOBILE TRANSCEIVERS
iF6120D
Series