Insignia NS-ANT30DA Documentation

PACKAGE CONTENTS

• Outdoor antenna

• Mounting hardware kit

• J-Pole mounting bracket

• Quick Setup Guide

WARNING: INSTALLATION OF THIS PRODUCT NEAR POWER

LINES IS DANGEROUS. FOR YOUR SAFETY, FOLLOW THE

INSTALLATION DIRECTIONS.

NOTE:

A RG59 OR RG6 COAXIAL CABLE (NOT INCLUDED) MUST BE RUN TO CONNECT THE

ANTENNA TO THE TELEVISION.

MOUNTING TOOLS

•

Drill bits (5/32", 3/8")

•

Hammer

•

3/8" and 1/2" sockets/wrench

•

Pen or pencil

FEATURES

• 50-mile range (approximate)

•

Ultra-sensitive design pulls in distant, weak, or difficult signals

•

Designed for outdoor use

•

Includes versatile mounting pole

•

Full kit of installation parts included

•

Compatible with 4K Ultra HD TVs

ASSEMBLING J-SHAPE POLE TO BASE

Alignment

If possible, position your antenna toward the transmission tower.

To determine which channels are available in your area,

visit www.antennaweb.org. Type in your zip code to

get help with antenna placement.

3

Attach the antenna to a pole pointing towards a local TV tower, using the bracket, then

tighten the wing nuts FIRMLY to prevent slipping.

MOUNTING YOUR ANTENNA

Note

: When using an electric drill, you should wear protective eye goggles and make sure

that the drill bit is installed correctly to avoid injury. Take care when installing this antenna.

Professional installation is recommended if you are not comfortable with installing this product.

For wooden walls:

1

Use the antenna base to mark the screw locations.

2

Attach the antenna base to a wall with the included screws (×2).

Use self-tapping screw (8*50mm)

included, for installation to the wall.

Notes:

• You may choose to pre-drill the holes using a 3/32''

→

5/32'' drill bit.

• Make sure that the J-shape pole is upturned.

For concrete walls:

1

Use the antenna base to mark the drilling positions.

2

Use an electric drill with a 3/8'' drill bit to drill two holes that

are 1.9in. (38mm) deep, then clean the holes.

3

Use a hammer to insert the wall anchors (×2) into the holes,

4

Attach the antenna base to the wall with screws (×2). Tighten the

nuts FIRMLY to prevent slipping.

Note:

Make sure that the J-shape pole is upturned.

Before using your new product, please read these instructions to prevent any damage.

Final flat size: 23.25 × 5.32

in. (590.55 × 135 mm)

Final folded size: 3.92 × 5.32

in. (98.4 × 135 mm)

ASSEMBLING YOUR ANTENNA

1

Unfold the antenna elements (part A) , until they extend at

right angles to the plastic boom.

2

I

nstall the reflectors onto the part A.

4

Use a coaxial cable to connect the F connector on the antenna to connect the ANT/IN or

CABLE/IN port on the back of your TV.

QUICK SETUP GUIDE

High Gain

Outdoor Antenna

NS-ANT30DA

Coaxial cable

F connector

NOTE:

Once antenna elements and

reflectors are extended/installed, they

cannot be folded back/removed unless the

black plastic catch is pressed and held

down when returning the pieces back to

their original position.

Reflector

Reflector

• Do not install during rain

or lightning storms.

•

Do not install near high

voltage cables or

transformers.

Step 2

Put the set screw inside the J-shape pole and tighten

the nuts slightly. Adjust the pole to the position you

want, then tighten the nuts FIRMLY to prevent slipping.

Step 1

Place the J-shape pole into the mounting base.

Make sure that the screw holes in the pole and

the base align. Secure the pole to the base using

the 6*43mm screw and nut.

CAUTIONS

Base

plate

1

Concrete Wall

Base

plate

1

Wooden Wall

J-shape

pole

upturned

Base

plate

2

Wooden Wall

2

Concrete Wall

Base

plate

4

Concrete Wall

J-shape

pole

upturned

Concrete Wall

3

NS-ANT30DA_18-0032_QSG_V1_R5_EN.ai 1 3/19/2018 11:53:31 AM

NS-ANT30DA_18-0032_QSG_V1_R5_EN.ai

1

3/19/2018

11:53:31 AM

Insignia NS-ANT30DA Documentation

Insignia NS-ANT30DA Manual

Insignia NS-ANT30DA manual content summary: