Insignia NS-HWG1865 User Guide
Insignia NS-HWG1865 Manual
 |
View all Insignia NS-HWG1865 manuals
Add to My Manuals
Save this manual to your list of manuals |
Insignia NS-HWG1865 manual content summary:
- Insignia NS-HWG1865 | User Guide - Page 1
USER GUIDE Wood & Glass TV Stand for TVs up to 75" NS-HWG1865 SAFETY INFORMATION AND SPECIFICATIONS .2 PACKAGE CONTENTS: PARTS 3 PACKAGE CONTENTS: HARDWARE 4 ASSEMBLY INSTRUCTIONS 6 CARE AND MAINTENANCE 21 Before using your new product, please read these instructions to prevent any damage. - Insignia NS-HWG1865 | User Guide - Page 2
the maximum width may result in instability, which may result in injury. The base of the television must be placed behind the stopper. See instructions for more details. CAUTION: This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children - Insignia NS-HWG1865 | User Guide - Page 3
Tools needed: Wood & Glass TV Stand Hammer Phillips screwdriver Rubber mallet 3/8" drill bit Power drill PACKAGE CONTENTS: PARTS Make sure that you have all the parts necessary to assemble your new TV stand. A Top panel (1) Note: Keep the stopper template attached to the top panel. B Left - Insignia NS-HWG1865 | User Guide - Page 4
all the hardware necessary to assemble your new TV stand. Label Hardware Qty. Label Hardware N Wood dowel M8 x 30 mm 26 W Shelf support NS-HWG1865 Qty. 8 P Cam pin 22 X Knob 4 Q Cam lock 22 Y Knob bolt 4 Screw R M4 x 50 mm 6 Z Corner connector 2 S Flat head screw M3 - Insignia NS-HWG1865 | User Guide - Page 5
Wood & Glass TV Stand INSTALLATION TIPS Gluing wood dowels (N) When using a wood dowel (N), put one drop of glue (CC) in the hole before you insert the wood dowel (N). Insert the wood dowel (N), then gently tap it with a rubber mallet to secure it in place. 1 2 GLUE 3 4 FINAL X Locking cam - Insignia NS-HWG1865 | User Guide - Page 6
NS-HWG1865 ASSEMBLY INSTRUCTIONS Step 1: Screw cam pins onto the top panel, bottom shelf, and skirtings Tip: Assemble your stand on a carpeted floor or the empty TV stand carton - Insignia NS-HWG1865 | User Guide - Page 7
Wood & Glass TV Stand Step 2: Attach the back skirting between the side skirtings 1 Glue two wood dowels (N) into the drilled holes on the ends of the back skirting (G). Tip: See "Gluing wood dowels (N)" on page 5 for more information. 2 Attach the back skirting to the side skirtings (H and I) by - Insignia NS-HWG1865 | User Guide - Page 8
NS-HWG1865 Step 3: Attach the front skirting to the side skirtings 1 Glue two wood dowels (N) into the drilled holes on the front skirting (F). 2 Attach the front skirting (F) to the side skirtings (H and I) by inserting two cam locks (Q) and tightening with a screwdriver. Make sure that the cam - Insignia NS-HWG1865 | User Guide - Page 9
Wood & Glass TV Stand Step 4: Attach the assembled base to the bottom shelf 1 Glue 10 wood dowels (N) into the drilled holes on the bottom shelf (E). 2 Position the assembled base onto the wood dowels (N) and cam pins (P) on the bottom shelf (E). Make sure that the pilot holes for the corner - Insignia NS-HWG1865 | User Guide - Page 10
NS-HWG1865 Step 5: Install two floor levelers to the assembled base 1 Using the pilot holes as a guide, fasten two corner connectors (Z) to the joints where the front skirting (F) meet with the side skirtings (H and I) with eight 15 mm flat head screws (S). 2 Screw - Insignia NS-HWG1865 | User Guide - Page 11
door stoppers to the top panel Note: Keep the stopper template attached to the top panel (A). • Using the pilot holes as a guide, attach two door stoppers (U) onto the front supports on the top panel (A) with two 15 mm flat head screws (S) per stopper. Make sure that the right angle sides of the - Insignia NS-HWG1865 | User Guide - Page 12
NS-HWG1865 Step 7: Align and attach the side panels to the top panel 1 Glue two wood dowels (N) into the holes on the top edge of the left side panel (B). 2 Attach the left side panel to the top panel (A) by inserting two cam locks (Q) and tightening with a screwdriver. Make sure that the door hinge - Insignia NS-HWG1865 | User Guide - Page 13
Wood & Glass TV Stand Step 8: Attach the partition panel to the top panel 1 Glue two wood dowels (N) into the inner holes on the top edge of the partion panel (D). 2 Attach the partition panel to the top panel (A) by inserting two cam locks (Q) and tightening with a screwdriver. Door hinge mounting - Insignia NS-HWG1865 | User Guide - Page 14
NS-HWG1865 Step 9: Attach the bottom shelf to both side panels and partition panel 1 Glue six wood dowels (N) into the holes on the bottom edge of side panels (B and C) and partition panel (D). 2 Align the drilled holes on the bottom shelf (E) with the installed wood dowels (N) on both side panels - Insignia NS-HWG1865 | User Guide - Page 15
Wood & Glass TV Stand Step 10: Attach the back panel to the assembled console frame 1 Go back and tighten all cam locks and screws. Make sure that all the parts are tight and there are no gaps between the pieces. This will help keep the unit square. 2 Turn the assembled unit over so that its back is - Insignia NS-HWG1865 | User Guide - Page 16
into the cross slots on the visible cam locks on the vertical panels (B, C, and D). 3 Insert eight shelf supports (W) into the holes in the sides of the compartments. Make sure that you place the shelf supports at the same level so the shelves are not tilted. 4 Tilt and rest the adjustable shelves - Insignia NS-HWG1865 | User Guide - Page 17
Wood & Glass TV Stand Step 12: Attach doors to the vertical panels 1 Push the knob bolts (Y) through the inside of each door (L), then screw on the knobs (X). 2 Attach a door (L) to the right side panel (C) by engaging both door hinges together as shown: A Extend both hinges of the door (L) to the - Insignia NS-HWG1865 | User Guide - Page 18
NS-HWG1865 Step 13: Attach the stopper to the top panel To prevent your TV from tipping, you must follow these instructions if you place a TV on top of your stand. Otherwise, skip to "Step 14: Change the door panel" on page 19. If your TV has - Insignia NS-HWG1865 | User Guide - Page 19
Wood & Glass TV Stand Step 14: Change the door panel Follow these steps if you want to change your TV stand's door panels from glass to wood. Otherwise, skip to "Step 15: Position the TV stand and install the tipping restraint hardware kit" on page 20. 1 Open a door (L) and loosen the screws on the - Insignia NS-HWG1865 | User Guide - Page 20
kit 1 Position the assembled stand against the wall where you plan to use it. 2 Adjust the leveling feet to level the TV stand. 3 Follow the instructions printed on the bag containing the tipping restraint hardware kit (EE) to attach the restraint hardware to the wall and the stand. WARNING: It is - Insignia NS-HWG1865 | User Guide - Page 21
the following chart. Look out for: What can happen: How to avoid the problem: • Children climbing on the stand. • Risk of injury or death. • in the instructions. • Work from the bottom to the top when loading shelves. • The bottom shelves can only support 50 lbs. while the top can support 135 - Insignia NS-HWG1865 | User Guide - Page 22
become the property of Insignia and are not returned to you. If service of Products or parts are required after the Warranty Period expires, does the warranty not cover? This warranty does not cover: • Customer instruction/education • Installation • Set up adjustments • Cosmetic damage • Damage due - Insignia NS-HWG1865 | User Guide - Page 23
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2017 Best Buy. All rights
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
 |
 |
USER GUIDE
SAFETY INFORMATION AND SPECIFICATIONS .2
PACKAGE CONTENTS: PARTS
..................................
3
PACKAGE CONTENTS: HARDWARE
.......................
4
ASSEMBLY INSTRUCTIONS
......................................
6
CARE AND MAINTENANCE
...................................
21
Wood & Glass TV Stand
for TVs up to 75”
NS-HWG1865
Before using your new product, please read these instructions to prevent any damage.