Insignia NS-ICEF2W2 User Guide
Insignia NS-ICEF2W2 Manual
 |
View all Insignia NS-ICEF2W2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Insignia NS-ICEF2W2 manual content summary:
- Insignia NS-ICEF2W2 | User Guide - Page 1
Ice Maker NS-ICEF2W2 USER GUIDE Before using your new product, please read these instructions to prevent any damage. - Insignia NS-ICEF2W2 | User Guide - Page 2
Contents Introduction 2 IMPORTANT SAFETY INSTRUCTIONS 3 Features 4 Package contents 4 automatic ice maker 21 Maintaining your ice maker 21 Troubleshooting 22 Specifications 23 ONE-YEAR LIMITED WARRANTY 24 Introduction Congratulations trouble-free performance. 2 www.insigniaproducts.com - Insignia NS-ICEF2W2 | User Guide - Page 3
on the bottom of the ice maker. 7 Refer all servicing to qualified service personnel. Servicing is required when the appliance has been damaged in any way or has been dropped. WARNING Electric Shock Hazard Failure to follow these instructions can result in electric shock, fire, or death. 1 WARNING-Do - Insignia NS-ICEF2W2 | User Guide - Page 4
or lack of experience and knowledge if they are given supervision or instruction concerning the use of the appliance in a safe way and understand component part is damaged, it must be replaced by the manufacturer, its service agent, or similar qualified persons in order to avoid a hazard. 6 WARNING - Insignia NS-ICEF2W2 | User Guide - Page 5
Tools and materials needed Ice Maker Putty knife Electric drill with a Needle nose pliers or nut driver Adjustable wrench Knife 1/4" drill bit Flat blade screwdriver 1/4" OD copper supply line with compression nuts and ferrules Shut off valve (non self piercing) Phillips screwdriver - Insignia NS-ICEF2W2 | User Guide - Page 6
3 Remove the plug from the inside of the freezer compartment with a putty knife. Plug 4 Peel off the label covering the ice maker hole on the back of the refrigerator, then remove the foam from the hole with the needle nose pliers. Retain the foam for future use. Remove label 6 www. - Insignia NS-ICEF2W2 | User Guide - Page 7
Ice Maker 5 Push the water inlet tube into the small hole on back of refrigerator. Rotate while inserting the tube until the flat surface of inlet tube is tight against the back of the refrigerator. 6 Secure the water inlet tube to the back of the refrigerator with two self-drilling screws ( - Insignia NS-ICEF2W2 | User Guide - Page 8
8 Insert the two ice maker mounting screws into the holes in the freezer wall. Turn each screw clockwise five times. Ice maker mounting screws 9 Use needle nose pliers to remove the terminal cover located at the top of the freezer by first pulling down one side of the cover, then pulling down the - Insignia NS-ICEF2W2 | User Guide - Page 9
Ice Maker 10 With the ice maker in one hand, plug the wiring harness connector into the terminal located at the top of the freezer panel. Make sure that the connection is tight. Make sure that the wiring harness is still in the hook on the back of ice maker. Terminal Wiring harness connector 11 - Insignia NS-ICEF2W2 | User Guide - Page 10
12 Adjust the leveling bracket to level the ice maker. The ice maker is level when the gap between the freezer wall and the ice maker is the same at the top and bottom. Ice maker Screws Leveling bracket 13 With the ice maker level, insert the third ice maker mounting screw at the bottom of the ice - Insignia NS-ICEF2W2 | User Guide - Page 11
Ice Maker 15 Locate the pre-punched holes at the bottom right corner of the back panel of the refrigerator. Align the water valve bracket with the factory drilled holes, then use a Phillips head screwdriver to drive the two self-drilling screws through the bracket and into the cabinet. Fixing - Insignia NS-ICEF2W2 | User Guide - Page 12
17 Grasp the other end of the plastic tube and push it firmly into the quick-connection on the valve until it bottoms out. Water valve Plastic water supply tubing 18 Clean the back of the cabinet with a commercial household cleaner, ammonia, or alcohol before applying the clamps. 19 Secure the - Insignia NS-ICEF2W2 | User Guide - Page 13
drawers from the freezer compartment. 3 Remove the small screws on both sides of the guide rail of the freezer compartment door, then remove the freezer compartment door, with the guide rail support, from the guide rail. 4 Remove the ice maker unit and the connection plate from the accessories bag - Insignia NS-ICEF2W2 | User Guide - Page 14
5 Remove the terminal cover from the upper left corner of the freezer compartment, then remove the ice maker mounting screws from the accessory bag and attach them loosely to the two mounting holes in the back of the freezer compartment. Mounting screws Terminal Remove terminal cover 6 Insert the - Insignia NS-ICEF2W2 | User Guide - Page 15
Ice Maker 8 Reinstall the freezer door guide rail and replace the freezer drawers, then place the ice storage bin in the top freezer drawer. Wire signal arm Ice storage bin Freezer drawer - Insignia NS-ICEF2W2 | User Guide - Page 16
10 Use needle nose pliers to remove the thermal insulation foam strip from the hole you just exposed. Thermal insulation 11 Remove the water tube connector, silicone seal, long water supply tube, and white head screw from the accessory bag, then assemble the parts by aligning the notch on the - Insignia NS-ICEF2W2 | User Guide - Page 17
Ice Maker 13 Locate the pre-punched holes at the bottom right corner of the back panel of the refrigerator. Align the water valve bracket with the factory drilled holes, then use a Phillips head screwdriver to drive the two self-drilling screws through the bracket and into the cabinet. Factory pre- - Insignia NS-ICEF2W2 | User Guide - Page 18
15 Grasp the other end of the plastic tube and push it firmly into the quick-connection on the valve until it bottoms out. Water valve Plastic water supply tubing 16 Secure the plastic water supply tubing to the back of the cabinet with three plastic clamps. Plastic clamps 18 www.insigniaproducts. - Insignia NS-ICEF2W2 | User Guide - Page 19
is not warranted by the refrigerator or ice maker manufacturer. • Follow these instructions carefully to minimize the risk of water damage. • Water hammer (water banging • The ice maker should be installed by an authorized service technician. • Make sure that the refrigerator is unplugged to - Insignia NS-ICEF2W2 | User Guide - Page 20
8 Tighten the compression nut securely. For plastic tubing, insert the molded end of the tubing into the valve and tighten the compression nut until it is hand-tight, then tighten one additional turn with a wrench. Over-tightening may cause leaks. 9 Place the end of the water supply line into a sink - Insignia NS-ICEF2W2 | User Guide - Page 21
maker Remember that water quality determines the quality of ice. The ice maker should not be connected to softened water. If the water softener has problems, chemical substances can damage the ice maker. To turn off the ice maker, raise the wire signal arm until it locks in the "up" off - Insignia NS-ICEF2W2 | User Guide - Page 22
Troubleshooting CAUTION: Do not try to repair your ice maker yourself. Doing so invalidates the warranty. PROBLEM POSSIBLE CAUSE sure that the water supply valve is turned on. Inspect the water supply line for problems. The ice smells funny The ice storage bin needs cleaning. Empty and wash the - Insignia NS-ICEF2W2 | User Guide - Page 23
Ice Maker PROBLEM The ice smells funny or tastes bad The ice is discolored POSSIBLE CAUSE POSSIBLE SOLUTION The ice storage bin or Empty and wash the ice - Insignia NS-ICEF2W2 | User Guide - Page 24
become the property of Insignia and are not returned to you. If service of Products or parts are required after the Warranty Period expires, not cover: • Food, beverage, and or medicine loss/spoilage • Customer instruction/education • Installation • Set up adjustments • Cosmetic damage • Damage due - Insignia NS-ICEF2W2 | User Guide - Page 25
operation or maintenance • Connection to an incorrect voltage or power supply • Attempted repair by any person not authorized by Insignia to service the Product • Products sold "as is" or "with all faults" • Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.) • Products - Insignia NS-ICEF2W2 | User Guide - Page 26
www.insigniaproducts.com 1-877-467-4289 (U.S. and Canada) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2021 Best Buy. All rights reserved. V2 ENGLISH 21-0978
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
 |
 |
Before using your new product, please read these instructions to prevent any damage.
USER GUIDE
Ice Maker
NS-ICEF2W2