Insignia NS-PDP42 RS232 Serial Commands (English)

Insignia NS-PDP42 Manual

Get Insignia NS-PDP42 PDF manuals and user guides View all Insignia NS-PDP42 manuals
Add to My Manuals
Save this manual to your list of manuals

Insignia NS-PDP42 manual content summary:

  • Insignia NS-PDP42 | RS232 Serial Commands (English) - Page 1
    with third party RS-232 control hardware and software. The instructions below are provided to help with programming software or to test functionality using telenet software. RS-232C Setup B IN DIGITAL AUDIO REMOTE AUDIO OUT (RGB/DVI) SERVICE CONTROL IN OPTICAL PONENT IN RS-232C IN (CONTROL
  • Insignia NS-PDP42 | RS232 Serial Commands (English) - Page 2
    Input label SimpLink Key Lock Caption ISM Method Low Power Set ID G 1 1 APPENDIX Communication Parameters 23 I Baud rate: 9600 bps (UART) I Data length: 8 bits I Parity: None I Stop bit: 1 bit I Communication code: ASCII code I Use a crossed (reverse) cable. ! NOTE G This product has
  • Insignia NS-PDP42 | RS232 Serial Commands (English) - Page 3
    . Red Adjustment k e 0~1 20. Green Adjustment k f 0 ~ 64 21. Blue Adjustment k g 0 ~ 64 22. ISM Method j h 0 ~ 64 23. Low Power j i 0 ~ 64 25. Channel Add/Del m j 0 ~ 64 26. Key m k 0 ~ 64 27. Back Light m l 0~1 LCD TV Model Only m 0~1 Plasma TV Model Only r 0 ~ 64
  • Insignia NS-PDP42 | RS232 Serial Commands (English) - Page 4
    04. Aspect Ratio (Command: k c) To adjust the screen format. You can also adjust the screen format using the RATIO button on remote control or in the Picture menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 1: 4:3 5: Zoom 2 2: 16:9 6: Set by program 4: Zoom 1 9: Just scan Reserved
  • Insignia NS-PDP42 | RS232 Serial Commands (English) - Page 5
    and front panel controls on the TV, use this mode. When main power is on/off, remote control lock is released. 15. Treble (Command: k r) To adjust treble. You can also adjust treble in the Audio menu. Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 (*transmit by Hexadecimal code
  • Insignia NS-PDP42 | RS232 Serial Commands (English) - Page 6
    Plasma TV model) To avoid having a fixed image remain on screen. Transmission [ j ][p][ ][Set ID][ ][Data][Cr] Data 1: Inversion 2: Orbiter 4: White Wash 8: Normal Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x] 23. Low Power (Command: j q) (Only Plasma TV model) To control the low power
  • Insignia NS-PDP42 | RS232 Serial Commands (English) - Page 7
    Main/Sub Picture 6 Two/One Part Channel 5 Using remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code: Refer to page 88. Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x] 27. Back Light (Command: m g) (Only LCD TV model) To adjust screen back light. Transmission [m][g][ ][Set
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
APPENDIX
89
EXTERNAL CONTROL THROUGH RS-232C
RS-232C Setup
The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the TV’s functions externally.
■
Note: RS-232C on this unit is intended to be used with third party RS-232 control hardware and software.
The instructions below are provided to help with programming software or to test functionality using telenet
software.
B IN
PONENT IN
AV IN 1
AUDIO
(RGB/DVI)
RS-232C IN
(CONTROL & SERVICE)
AUDIO
AUDIO OUT
VIDEO
MONO
(
)
AUDIO
S-VIDEO
REMOTE
CONTROL IN
SERVICE
DIGITAL
AUDIO OUT
OPTICAL
Type of Connector; D-Sub 9-Pin Male
No.
Pin Name
1
No connection
2
RXD (Receive data)
3
TXD (Transmit data)
4
DTR (DTE side ready)
5
GND
6
DSR (DCE side ready)
7
RTS (Ready to send)
8
CTS (Clear to send)
9
No Connection
1
6
5
9
PC