Insignia NS-RMTLG17 Quick Setup Guide

V1 ENGLISH

17-0214

Before using your new product, please read these instructions to

prevent any damage.

QUICK SETUP GUIDE

Replacement

Remote

Control

For

LG TVs

NS-RMTLG17

PACKAGE CONTENTS

•

Replacement Remote Control for LG TVs

•

Quick Setup Guide

INSTALLING BATTERIES

•

Insert two AAA batteries (not included) into the

remote. Make sure that

the + and – symbols

match the + and –

symbols in the battery

compartment.

Note

: To set up your

remote, follow the setup

steps below, in order, and STOP as soon as your remote

works correctly.

SETTING UP YOUR REMOTE

Your remote should work with most newer LG TVs

without requiring any setup. After you install the

batteries, test your remote. If the buttons work correctly,

your remote is ready to use and you do not need to do

any further setup.

If the buttons do not work, complete the following

steps:

1

Make sure that your TV is on and not in standby mode.

2

On your remote, press and hold the red and blue

buttons until the

POWER

button blinks twice.

3

Point your remote towards the TV, then press and hold

POWER

until your TV turns off. As soon as your TV

turns off, immediately release the button. You have

three seconds to release the button before your

remote sends a different signal (code) to your TV. The

POWER


4

Use your remote to turn on your TV, then test the other

buttons. If the buttons work, your remote is ready to

use.

If some of the buttons still do not work, complete the

following steps:

1

Make sure that your TV is on and not in standby mode.

2

On your remote, press and hold the red and blue

buttons until the

POWER


3

Point your remote towards your TV, then press and

hold one of the buttons (such as

MENU

) that is not

working correctly.

As soon as the correct function (in this example,

MENU

) appears on your TV screen,

immediately

release the button

. The

POWER


You have three seconds to release the button before

your remote sends a different signal (code) to your TV.

4

Test the rest of the buttons. If the buttons work, your

remote is ready to use.

5

If some of the buttons still do not work, repeat the

above steps for another non-working button, then test

the rest of the buttons. Repeat until all the buttons

work.

LEARNING FUNCTIONS

Your remote can learn any function from your original

remote as long as the original remote works.

1

Place both remotes on a flat surface with the infrared

eyes facing each other.

Note

: If you have difficulty with the learning function, install

new batteries in both remotes and try the process again.

Make sure that the remote control “eyes” are pointing at

each other and are 1-2 inches apart.

2

On your new remote, press and hold the green and

yellow buttons until the

POWER


3

On your new remote, press

975

. The

POWER

button

blinks twice.

4

On your new remote, press the button you want to

learn a new function (for example,

VOL+

).

5

On the original remote control, press the button with

the function you want to teach to the button you

pressed in step 4.

If the

POWER

button blinks twice, your new remote

learned the function. You can repeat steps 4 and 5 to

add another function to your new remote.

If the

POWER

button blinks one long blink, your new

remote did not learn the function. Repeat steps 4 and 5.

6

After you teach your new remote all the functions

you want it to learn, press and hold

OK

for three

seconds until the

POWER


DELETING A LEARNED FUNCTION

1

Press and hold the green and yellow buttons until

the

POWER


2

Press

976.

3

Press the button you want to reset twice

(for example,

VOL+

). The

POWER

button blinks

twice and the button is reset to its original function.

TROUBLESHOOTING

POWER button does not blink when a button is

pressed.

•

Replace the batteries.

LEGAL NOTICES

FCC Statement:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception, which

can be determined by turning

the equipment off and on, the

user is encouraged to try to correct the interference by one or

more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and

receiver.

—Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV

technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2)

this device must accept any interference received,

including interference that may cause undesired

operation.

Caution:

Changes or modifications not expressly

approved by the party responsible for compliance could

void the user's authority to operate the equipment

.

ONE-YEAR LIMITED WARRANTY

Visit www.insigniaproducts.com for details.

CONTACT INSIGNIA:

For customer service, call1-877-467-4289

www.insigniaproducts.com

INSIGNIA is a trademark of Best Buy and its affiliated companies

Distributed by Best Buy Purchasing, LLC

7601 Penn Ave South, Richfield, MN 55423 U.S.A.

©2017 Best Buy. All rights reserved

Made in China

2 X AAA

1±2 in.

Original remote

New remote

Insignia NS-RMTLG17 Quick Setup Guide

Insignia NS-RMTLG17 Manual

Insignia NS-RMTLG17 manual content summary: