Intel SR1690WB Service Guide

Intel SR1690WB - Server System - 0 MB RAM Manual

Get Intel SR1690WB - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858210980
View all Intel SR1690WB manuals
Add to My Manuals
Save this manual to your list of manuals

Intel SR1690WB manual content summary:

  • Intel SR1690WB | Service Guide - Page 1
    Intel® Server System SR1690WB Service Guide A Guide for Technically Qualified Assemblers of Intel® Identified Subassemblies/ Products Intel Order Number E78186-004
  • Intel SR1690WB | Service Guide - Page 2
    Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. * Other names and brands may be claimed as the property of others. Copyright © 2010, Intel Corporation. All Rights Reserved ii Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 3
    components you may need, troubleshooting information, and instructions on how to add and replace components on the Intel® Server System SR1690WB. For the latest version of this manual, see http://support.intel.com/ support/motherboards/server/S5500WB. Manual Organization Chapter 1 provides a list
  • Intel SR1690WB | Service Guide - Page 4
    or want to purchase one or more of the following items for your server: • One or two Intel® Xeon 5500 series and Intel® Xeon 5600 series processors • DDR3 RDIMM/UDIMM Memory • Hard drive • Slimline CD-ROM or DVD-ROM drive • RAID controller add-in card iv Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 5
    about which accessories, memory, processors, and third-party hardware were tested and can be used with your board, and for ordering information for Intel products, see: http://support.intel.com/support/motherboards/server/ S5500WB/compat.htm Intel® Server System SR1690WB Service Guide v
  • Intel SR1690WB | Service Guide - Page 6
    vi Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 7
    in this document before performing any of the instructions. See also Intel Server Boards and Server Chassis Safety Information on the Intel® Server Deployment Toolkit CD and/or at http://support.intel.com/support/ motherboards/server/sb/cs-010770.htm. Wichtige Sicherheitshinweise Lesen Sie
  • Intel SR1690WB | Service Guide - Page 8
    the contacts inside the jumper, causing intermittent problems with the function controlled by that jumper. Take care to grip with, but not squeeze, the pliers or other tool you use to remove a jumper, or you may bend or break the pins on the board. viii Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 9
    Mounted Systems ...20 Hardware Requirements ...21 Processor ...21 Memory ...21 Memory Sparing and Mirroring 22 Power Supply ...23 Optional Hardware ...23 Intel® RAID Activation Key 23 Intel® Remote Management Module 3 23 Intel® I/O Expansion Module 24 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 10
    NIC 50 Removing the Intel® RMM3 and Intel® RMM3 NIC 51 Replacing the Backplane Board 51 Removing the Backplane Board 52 Installing the Backplane Board 52 Replacing the Server Board 53 Removing the Server Board 53 Installing the Server Board 54 x Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 11
    Power Supply Input Voltages 67 650-W Single Power Supply Output Voltages 67 System Environmental Specifications 68 Appendix B: Intel® Server 92 Rack Mount Installation Guidelines 93 Power Cord Usage Guidelines 94 Product Ecology Compliance 95 Intel® Server System SR1690WB Service Guide xi
  • Intel SR1690WB | Service Guide - Page 12
    Intel® Chassis Subassembly Products 101 Extent of Limited Warranty 101 Limitations of Liability 102 How to Obtain Warranty Service 102 Appendix G: Installation/Assembly Safety Instructions 105 Important Safety Instructions le montage en rack 122 xii Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 13
    cable de alimentación 126 Advertencias el acceso al sistema 127 Advertencias sobre el montaje en bastidor 128 Descarga electrostática (ESD 129 Otros riesgos ...129 Intel® Server System SR1690WB Service Guide xiii
  • Intel SR1690WB | Service Guide - Page 14
    xiv Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 15
    Connector and Component Locations 10 Figure 5. Configuration Jumper Location 12 Figure 6. Light Guided Diagnostic LEDs 14 Figure 7. Back Panel Connectors 15 Figure 8. Front Control Panel - Intel® Server System SR1690WB 17 Figure 9. Server System I/O Connector Locations 19 Figure 10. Optional
  • Intel SR1690WB | Service Guide - Page 16
    the Power Supply into the Server System 59 Figure 49. Installing the Rack Handle 60 Figure 50. Removing the Rack Handle 60 Figure 51. CMOS Recovery Jumper 65 Figure 52. Password Recovery Jumper 66 Figure 53. Diagnostic LED Placement Diagram 73 xvi Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 17
    Table 1. Server System References 1 Table 2. Intel® Server System SR1690WB Feature Summary 3 Table 3. NIC LED Descriptions 15 Table 4. Control Panel LED Functions 17 Table 5. List of Supported I/O Modules on SR1690WB 24 Table 6. Setup Menu Key Use 62 Table 7. 650-W Single Power Supply Output
  • Intel SR1690WB | Service Guide - Page 18
    xviii Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 19
    Found at: http://support.intel.com/support/motherboards/server/S5500WB/ Intel® Server System SR1690WB Quick Start User's Guide in the product box Accessories or other Intel Spares and Configuration Guide can be found at: server products http://support.intel.com/support/motherboards/server/S5500WB
  • Intel SR1690WB | Service Guide - Page 20
    .intel.com/support/motherboards/server/S5500WB/ Diagnostics: Platform Confidence Test (PCT) Found at: http://support.intel.com/support/motherboards/server/S5500WB/ and available on the Intel®Server Deployment Toolkit 3.0 CD that ships with your system. 2 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 21
    location of important components and connections on the server system. DevOicpetical AF003210 Figure 1. Intel® Server System SR1690WB Table 2 summarizes the features of the server system. Table 2. Intel® Server System SR1690WB Feature Summary Feature Description Dimensions • 1.69 inches (43mm
  • Intel SR1690WB | Service Guide - Page 22
    CPU fans • Two sets of DIMM fans Intel® Server Board S5500WB SSI-compliant One riser slot supporting full-height or low-profile 1U and 1U MD2 PCI Express* x16 riser cards. Two connectors supporting double- and single-wide Intel®I/O Expansion Modules. 4 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 23
    2. Intel® Server System SR1690WB Feature Summary Feature On-board Video LAN Support System Power System Management Description On-board Server Engines* LLC Pilot II Controller Matrox* G200 2D Video Graphics controller Uses 8 MB of the BMC 32 MB DDR2 Memory Two 10/100/1000 ports provided by Intel
  • Intel SR1690WB | Service Guide - Page 24
    correctly before reinstalling the server system cover. Use caution to make sure no cables or wires are pinched and that the airflow from the fans is not blocked. Use the following figures to determine the correct cable routing for the SR1690WB system. 6 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 25
    Power L Power to Fans M Power to Optical Drive N Power to Backplane(2) G O IPMB Cable from Backplane P SGPIO Cable from Backplane Q SATA Data Cables 50 41 32 I C Server Board J L L B K F1 2 P HDD 0 34 Q N M D HDD 1 HDD 2 N HDD 3 O E Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 26
    H. Mother board C. Hot swap backplane I. 650W power supply unit D. System Fans (CPU fans and Memory fans) J. Optional slimline optical drive E. Air Duct K. Hot swap HDD carrier F. PCI Express* add-in card bracket Figure 3. System Components 8 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 27
    Gen2 X. Processor Socket 2 C. Remote Management Module 3 Y. 4-pin Fan Connector (CPU2) D. POST Code LEDs Z. 4-pin Fan Connector (CPU2A) E. External I/O AA. 4-pin Fan Connector (MEM2) F. USB Connector BB. 8-pin Fan Connector (MEM2R) Intel® Server System SR1690WB Service Guide 9
  • Intel SR1690WB | Service Guide - Page 28
    DD. DIMM Slot D1 I. 24-pin Power Connector EE. DIMM Slot E1 J. N/A FF. DIMM Slot F1 K. Aux Power (5-pin or 7-pin) GG. Front Panel . Serial Port B U. N/A V. Processor Socket 1 Figure 4. Server Board Connector and Component Locations 10 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 29
    Configuration Jumpers A BMC Force Update J1B5 A D Normal Update Password Clear J1C2 B B C Normal Clear Password BIOS Recovery Mode J1C3 C E Internal External 6HULDO ,QWHUIDFH J6A2 F DCD to DTR DSR to DTR ME BMC Update J7A2 AF003049 Intel® Server System SR1690WB Service Guide 11
  • Intel SR1690WB | Service Guide - Page 30
    image. Normal System Operation (Default) Clear CMOS settings Internal connector overrides External connector overrides DTR (Data Terminal Ready) mode DCD (Data Carrier Detect) mode DSR (Data Set Ready) mode Figure 5. Configuration Jumper Location 12 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 31
    5-V STBY LED on the server board (see Figure 6) is illuminated (green) when AC power is applied. • The Fan Fault LEDs on the server board (see Figure 6) help identify failed and failing fans. The fan fault LEDs turn on (amber) if there is a fan fault. Intel® Server System SR1690WB Service Guide 13
  • Intel SR1690WB | Service Guide - Page 32
    FLT_D1 FLT_E FLT_D2 D E FLT_A2 FLT_B FLT_A1 FLT_C F AF003216 A. Diagnostic LED B. System Status LED C. System ID LED D. 5V Standby LED E. CPU1 DIMM fault LEDs F. Fan Fault LEDs G. CPU2 DIMM fault LEDs Figure 6. Light Guided Diagnostic LEDs 14 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 33
    network connection Network connection in place Transmit/receive activity 10 Mbps connection (if left LED is on or blinking) 100 Mbps connection 1000 Mbps connection Intel® Server System SR1690WB Service Guide 15
  • Intel SR1690WB | Service Guide - Page 34
    on the SATA Key connector that is located at the right side of the server board. For information on how to install the Intel® RAID Activation Key AXXRAKSW5 accessory to enable RAID 5, see the documentation that is included with the accessory kit. 16 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 35
    Panel LED Functions LED Color Power/ Sleep Green Green - LAN 1 and LAN 2 Green Green - State On Blink Off On Blink Off Description Power On/ACPI S0 state Sleep /ACPI S1 state Power Off /ACPI S5 state LAN Link no Access LAN Activity No Link Intel® Server System SR1690WB Service Guide 17
  • Intel SR1690WB | Service Guide - Page 36
    is powered on until the BIOS clear it. If the system is not powered down normally, it is possible the Power LED will blink at the same time the system status LED is off due to a failure or configuration change that prevents the BIOS from running. 18 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 37
    Locations Peripheral Devices The server system provides locations and hardware for installing hard drives and a slimline optical drive. You must purchase the drives separately. The following figure shows the available options. A B ED C AF003221 Intel® Server System SR1690WB Service Guide 19
  • Intel SR1690WB | Service Guide - Page 38
    the top. In other words, install the first system in the rack into the bottom position of the rack, the second system in the second position from the bottom, and so on. Instructions for installing your chassis into a rack are included in the rail kit. 20 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 39
    the server board requires DDR3 DIMMs within a channel to be populated starting with the DIMM farthest from the processor. See the following figure (Figure 12). For a complete list of supported memory DIMMs, see the links under "Server System References". Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 40
    at different DIMM timings (RAS latency, CAS latency, and so forth). Memory Sparing and Mirroring The spare mode is not supported by Intel® Server System SR1690WB. With memory mirroring, the system maintains two copies of all data in the memory subsystem. If a DIMM fails, the data is not lost because
  • Intel SR1690WB | Service Guide - Page 41
    support WS-MAN and CIMOM. The RMM3 comes with a third 10/100GbE NIC that connects to the board. RMM3 management traffic can use the third NIC or NIC 1. To install the RMM3 module, following the instruction in the RMM3 kit package, which is purchased separately. Intel® Server System SR1690WB Service
  • Intel SR1690WB | Service Guide - Page 42
    I/O Expansion Module. Dual-port 10 Gigabit Ethernet I/O Expansion Module with CX4 connectors. Quad port Gigabit Ethernet I/O Expansion Module based on the Intel® 82576EB Gigabit Ethernet Controller. InfiniBand* I/O Expansion Module Single Port QDR. 24 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 43
    attention to the "Safety Information" at the beginning of this manual. Note: Whenever you service the system, you must first power down the server and unplug all peripheral devices and the AC power cord. Tools and Supplies Needed • Phillips* (cross head) screwdrivers (#1 bit and #2 bit) • Needle
  • Intel SR1690WB | Service Guide - Page 44
    of the cover sit just inside the server system sidewalls. Slide the cover forward (see letter "A" in Figure 14). 3. Tighten the screw at the rear of the server (see letter "B") and install the two screws at the front of the server (see letter "C"). 26 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 45
    Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the server system cover. For instructions, see "Removing the System Cover". 4. Lift the processor air duct from its location behind the two system blower fans. Intel® Server System SR1690WB Service Guide 27
  • Intel SR1690WB | Service Guide - Page 46
    4. Lower the air duct into place; align the air duct side walls to the corresponding slots on the bracket behind the four system blower fans and insert into position. Use caution not to pinch or disengage cables that may be near or under the air duct. 28 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 47
    install DIMMs, follow these steps: 1. Observe the safety and ESD precautions at the beginning of this book. 2. Turn off all peripheral devices connected to the server. 3. Turn off the server. 4. Disconnect the AC power cord from the server. Intel® Server System SR1690WB Service Guide 29
  • Intel SR1690WB | Service Guide - Page 48
    AC power cord from the server. 4. Remove the server's cover. 5. Gently spread the retaining clips at each end of the socket. The DIMM lifts from the socket. 6. Holding the DIMM by the edges, lift it from the socket, and store it in an anti-static package. 30 Intel® Server System SR1690WB Service
  • Intel SR1690WB | Service Guide - Page 49
    for instructions on removing the server's cover. 5. Locate the processor socket and open the socket lever (see Figure 18). A B AF003228 Figure 18. Lifting the Load Lever 6. Open the load plate (see letter "A" in Figure 18 and letter "B" in Figure 18). Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 50
    A B AF003229 Figure 19. Open the Load Plate 7. Remove the socket protective cover (see Figure 19). 8. Take the processor out of the box and remove the protective shipping cover (Figure 20). AF003292 Figure 20. Removing the socket 32 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 51
    . 9. Align the processor cutouts to match the two socket pins, and then insert the processor into the socket as shown in Figure 21. B A AF003293 Figure 21. Aligning the Processor 10. Close the package orientation and alignment with the socket: Intel® Server System SR1690WB Service Guide 33
  • Intel SR1690WB | Service Guide - Page 52
    your server chassis for instructions on installing the server's cover. Replacing a Processor 1. Observe the safety and ESD precautions at the beginning of this book. 2. Turn off all peripheral devices connected to the server. Turn off the server. 34 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 53
    cover over the empty processor socket and reinstall the chassis cover. Installing and Removing a Hot-swap Hard Drive You can install up to two fixed SATA drives in the Intel® Server System SR16WB90 Service Guide. See "Server System References" for a link to a list of supported hardware. Caution: If
  • Intel SR1690WB | Service Guide - Page 54
    surface. 4. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions. 5. With the drive circuit-side down, position the connector end of the drive so that it B A AF003303 Figure 25. 2.5 HDD Installation 36 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 55
    Installation 7. With the black lever in the fully open position, slide the drive assembly into the server system. The green latch at the front of the drive carrier must be to the right. Do into place. A B AF003305 Figure 27. Locking the drive assembly Intel® Server System SR1690WB Service Guide 37
  • Intel SR1690WB | Service Guide - Page 56
    the system or wall outlet. To maintain proper system cooling, if you do not install a device at this location, you must install the provided filler blank. Installing a Slimline Optical Drive 1. Remove the slimline drive bay filler blank, if installed. 38 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 57
    drive, and plug in the composed SATA/SATA Power cable, which is shipped in system package. B A AF003312 Figure 29. Attaching the Brackets to the Optical Drive 4. Lead the SATA/SATA Power cable through the optical drive bay before inserting the drive. Intel® Server System SR1690WB Service Guide 39
  • Intel SR1690WB | Service Guide - Page 58
    AF003313 6. Connect the SATA cable connector to SATA port 4 or 5 on server board. 7. Connect the SATA power connector to P6 connector from system power supply. B DevOicpetical A AF003314 Figure 30. Installing the Optical Drive into the Server System 40 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 59
    Riser Assembly from the Server System Installing the PCI Riser Assembly 1. Lower the riser assembly into place (see letter "A"). 2. Align the two hooks in the riser assembly with the matching slots at the back of the server system (see letter "B"). Intel® Server System SR1690WB Service Guide 41
  • Intel SR1690WB | Service Guide - Page 60
    After removing the PCI riser assembly from the server system, remove the screw that attaches the PCI bracket shield to the rear of the chassis to remove the shield. Retain the screw. 2. Insert the PCI card edge connector in the slot on the PCI riser. 42 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 61
    Tipping the riser card while installing into the slot may damage the riser card or slot on the server board. 4. Use the screw removed in step 1 to secure the riser card assembly to the B A Figure 34. Removing a PCI Card in a Riser Card AF003325 Intel® Server System SR1690WB Service Guide 43
  • Intel SR1690WB | Service Guide - Page 62
    of them fails. If a fan in the power supply fails, you must replace the power supply. Use the following steps to replace a system fan. Replacing the System Fans 1. Remove the processor air duct. For instructions, see "Removing the Processor Air Duct". 44 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 63
    2. Disconnect the two 4-pin or one 8-pin system fan cables from the server board. See letters "2" in the following figure. 3. Lift the failed fan from the module. 4. Remove the plastic screws from the failed fans and install them into the new fans. Intel® Server System SR1690WB Service Guide 45
  • Intel SR1690WB | Service Guide - Page 64
    . 6. With the fan oriented correctly, insert the fan into the fan module (see letter "3"), and insert the fan cable into the matching connector on the server board. (see letter "2"). 46 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 65
    fan module Installing and Removing the I/O Expansion Module(s) Installing the I/O Expansion Module(s) 1. Squeeze the sides of the I/O expansion module cover to disengage it from the server system back panel and remove it (see letter "A"). Intel® Server System SR1690WB Service Guide 47
  • Intel SR1690WB | Service Guide - Page 66
    Figure 38. Installing the I/O Expansion Module(s) 2. Attach the standoffs to the server board (see letter "A") and attach the I/O shield gasket to the module (see letter "B"). 3. Attach the I/O expansion module(s) to the server board (see letter "C"). 48 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 67
    Expansion Module(s) 1. Remove the I/O expansion module(s) from the server board (see letter "A"). 2. Remove the standoffs from the server board (see letter "B"). 3. Install the I/O expansion module cover into the system back panel (see letter "C"). Intel® Server System SR1690WB Service Guide 49
  • Intel SR1690WB | Service Guide - Page 68
    ® RMM3 NIC 2. Attach the bracket of Intel® RMM3 NIC module by two screws (see letter "A"). 3. Connect the Intel® RMM3 cable to the slot on server board (see letter "B"). 4. Attach the Intel® RMM3 module to rear chassis by two screws (see letter "C"). 50 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 69
    cable from the server board (see letter "B"). 3. Install the Intel® RMM3 NIC module cover into the system back panel (see letter "A"). Replacing the Backplane Board The instructions below describe how to replace the backplane board in the system. Intel® Server System SR1690WB Service Guide 51
  • Intel SR1690WB | Service Guide - Page 70
    , aligning with two screw holes on chassis. 2. Tighten two screws to lock the backplane assembly in position (see letter "B"). 3. Connect data/power cables to the backplane connectors. 4. Engage hard drives back to the backplane (see letter "C"). 52 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 71
    3. If installed, remove the PCI riser assembly. 4. If installed, disconnect all SATA cables from the server board. 5. Disconnect the system fans cables from server board. 6. Disconnect all power cables coming from the power supply to the server board. Intel® Server System SR1690WB Service Guide 53
  • Intel SR1690WB | Service Guide - Page 72
    server board. See "Installing the Server Board" on page -54. Installing the Server Board 1. Place the server board into the server system as shown in the following figure (see letter "A"). 2. Attach the server board with nine screws (see letter "B"). 54 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 73
    supply to the server board. 4. Re-connect the system fan cables to server board. 5. Re-connect all SATA cables to the server board. 6. Install the PCI riser assembly. 7. Install the memory, processor heat sinks, and processors. 8. Install the system air duct. Intel® Server System SR1690WB Service
  • Intel SR1690WB | Service Guide - Page 74
    power. When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in the RTC (for example, the date and time) may be wrong. Contact your customer service . Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. 56 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 75
    power button, and unplug the AC power cord from the system or wall outlet. Removing the Power Supply You can replace the power supply if it fails or if one of the fans integrated into it fails. To replace the power supply, use the following instructions. Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 76
    3. Lift the power supply up to clear the chassis tab (see letter "C") and remove the power supply by sliding it out (see letter "D"). Installing the Power Supply 1. Insert the replacement power supply by first engaging the back panel (see letter "A"). 58 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 77
    the power at the rear of the chassis (see letter "D"). Installing and Removing the Rack Handles Installing the Rack Handles 1. Align the rack handle with the holes on the side of the server system and attach the rack handle with the three screws. Intel® Server System SR1690WB Service Guide 59
  • Intel SR1690WB | Service Guide - Page 78
    the Rack Handle 2. Repeat step 1 on the opposite side of the server. Removing the Rack Handles 1. Remove the three screws holding the rack handle in place, and remove the rack handle from the server system. AF003327 Figure 50. Removing the Rack Handle 60 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 79
    server configuration defaults. You can run the BIOS Setup with or without an operating system being present. See "Server System References" for a link to the Intel® Server access BIOS Setup, you might need to clear the CMOS memory. For instructions on clearing the CMOS, see "Clearing the CMOS". Setup
  • Intel SR1690WB | Service Guide - Page 80
    . Setup Defaults - Pressing causes the following to display: Setup Confirmation Load default configuration now? [Yes] [No] If "Yes" is selected and is pressed, all Setup fields pressed without affecting any existing field values. 62 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 81
    the system to service. For additional information, see "Server System References" for a link to the necessary firmware and BIOS updates software and instructions. Recording You need these settings to configure your server at the end of the procedure. Intel® Server System SR1690WB Service Guide 63
  • Intel SR1690WB | Service Guide - Page 82
    block at J1B4 on the server board. 1. Power down the system; do not disconnect the AC power. 2. Open the server. 3. Move the jumper from the normal operation position, at pins 1 and 2 to the CMOS Clear Force Erase position, covering pins 2 and 3. 64 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 83
    the server board. 1. Power down the system and disconnect the AC power. 2. Open the server chassis. 3. Move the jumper from the normal operation position, Password Clear Protect, at pins 1 and 2 to the Password Clear Erase position, covering pins 2 and 3. Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 84
    power; power up the system. 5. Power down the system and disconnect the AC power. 6. Return the Password Reset jumper to the Password Protect position, covering pins 1 and 2. Reconnect AC power and power up the server Password Recovery Jumper AF003214 66 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 85
    usage for your configuration, see "Power Budget Tool." Table 7. 650-W Single Power Supply Output Voltages Voltage +3.3 V +5 V +12 V1 +12 V2 +12 V3 +12 V4 -12 V +5 VSB Maximum Continuous 13.8A 19.6A 11.3A 11.3A 9.1A 9.1A 0.43A 3.0A 1. Maximum continuous total DC output power should not exceed
  • Intel SR1690WB | Service Guide - Page 86
    Sound Power: 7.0 BA in an idle state at typical office ambient temperature. (23 +/- 2 degrees C). +/-12 kV except I/O port +/-8 KV, per Intel Environmental Test Specification. *The system requires the may cause improper operation of the product. 68 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 87
    . See the last page for space to include a detailed problem description Board / Chassis Information Baseboard Revision - PBA Baseboard Serial Number CPU1 Speed/Stepping/Spec CPU2 Speed/Stepping/Spec System BIOS Version HSC Firmware Version Chassis Model Intel® Server System SR1690WB 69
  • Intel SR1690WB | Service Guide - Page 88
    Other (Vendor/Model DIMM Configuration DIMM A1 MB and Vendor / part number DIMM A2 MB and Vendor / part E1 MB and Vendor / part number DIMM F1 MB and Vendor / part number Operating System Information Operating System Version Service Pack 70 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 89
    box below as applicable, and provide the requested information: Peripheral or Peripheral Description, Driver Revision, IRQ #, I/O Base Address, and FW Peripheral PCI Express* Gen2 x8 Platform Instrumentation only Intel® Remote Management Module Intel® Server System SR1690WB Service Guide 71
  • Intel SR1690WB | Service Guide - Page 90
    Complete Problem Description In the space below, provide a complete description of the steps used to reproduce the problem or a complete description of where the problem can be found. Please also include any details on troubleshooting already done 72 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 91
    of which is assigned a specific hex POST code number. As each configuration routine is started, the BIOS displays the POST code to the POST Code Diagnostic LEDs on the back edge of the server board. To assist in troubleshooting a system hang during the POST process, the Diagnostic LEDs can be used
  • Intel SR1690WB | Service Guide - Page 92
    Selection of Processor with least feature use as Boot Strap Processor 0x15h 0 0 0 1 0 1 0 1 Switch an AP processor to become the new Boot Strap Processor Chipset 0x21h 0 0 1 0 0 0 1 0 Initializing a chipset component Memory 74 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 93
    1 1 1 0 1 1 0 0 Unsupported or invalid DIMM configuration (system halted) 1 1 1 0 1 1 0 1 Unsupported or invalid DIMM configuration (system halted) 1 1 1 0 1 0 1 1 DIMM with corrupted SPD data detected (system halted) Intel® Server System SR1690WB Service Guide 75
  • Intel SR1690WB | Service Guide - Page 94
    1 1 0 0 1 1 Memory Initialization of Integrated Memory Controller 0xB4h 1 0 1 1 0 1 0 0 Memory Initialization of Integrated Memory Controller 0xB5h 1 0 1 1 0 1 0 1 Memory Initialization of Integrated Memory Controller 76 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 95
    1 0 1 1 1 1 0 1 Memory Initialization of Integrated Memory Controller 1 0 1 1 1 1 1 0 Memory Initialization of Integrated Memory Controller 1 0 1 1 1 1 1 1 Memory Initialization of Integrated Memory Controller Intel® Server System SR1690WB Service Guide 77
  • Intel SR1690WB | Service Guide - Page 96
    if supported by ATA device 1 1 0 1 Reserved for ATA 1 1 1 0 Resetting SMBUS 1 1 1 1 Reserved for SMBUS 0 0 0 1 Initializing I/O Controller Hub 0 0 1 1 Initializing Super I/O 0 0 0 0 Resetting the video controller (VGA) 78 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 97
    the presence of mouse 0 1 1 1 Enabling the mouse 0 0 1 0 Reserved for mouse 1 0 0 0 Resetting the serial port 1 0 0 1 Disabling the serial port 1 0 1 0 Detecting the presence of the serial port Intel® Server System SR1690WB Service Guide 79
  • Intel SR1690WB | Service Guide - Page 98
    device (IDE hard drive detection, and so on) 0 0 1 1 Enabling / configuring a fixed media device 0 1 0 0 Reserved for fixed media 1 0 0 0 policy 0 0 1 1 Connect boot device controller 0 1 0 0 Attempt flash update boot mode 80 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 99
    PEIM) 0xE2h 1 1 1 0 0 0 1 0 Initial memory found, configured, and installed correctly 0xE3h 1 1 1 0 0 0 1 0xEBh 1 1 1 0 1 1 0 1 Legacy Option ROM Initialization 0xECh 1 1 1 0 1 0 0 0 DXE Drivers initialized Intel® Server System SR1690WB Service Guide 81
  • Intel SR1690WB | Service Guide - Page 100
    crisis recovery capsule 0x36h 0 0 1 1 0 1 1 0 Begin crisis recovery 0x3Eh 0 0 1 1 1 1 1 0 No crisis recovery capsule detected 0x3Fh 0 0 1 1 1 1 1 1 Crisis recovery capsule failed integrity check of capsule descriptors 82 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 101
    System SR1690WB Service Guide Server Management at http:// www.intel.com/reseller/. Note: You will need to log in to the Reseller site to obtain the 24x7 number. Warranty Information To obtain warranty information, visit the following Intel web site: http://support.intel.com/support/motherboards
  • Intel SR1690WB | Service Guide - Page 102
    84 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 103
    assembly instructions in this guide server system, power supply, and other modules have passed EMC testing using a server board with a microprocessor from the same family (or higher) and operating at the same (or higher) speed as the microprocessor used on this server board. The final configuration
  • Intel SR1690WB | Service Guide - Page 104
    ) Certifications / Registrations / Declarations • NRTL ETL Certification (US/Canada) • CE Declaration of Conformity (CENELEC Europe) • FCC/ICES-003 Class A Attestation (USA/Canada) • VCCI Certification (Japan) 86 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 105
    Product Recycling Marks Product Regulatory Compliance References The following table references Server Chassis Compliance and markings that may appear on the product. Markings Reference Marking Example Argentina IRAM Certification (Safety) N232 Intel® Server System SR1690WB Service Guide 87
  • Intel SR1690WB | Service Guide - Page 106
    -3-2 (Harmonics) EN61000-3-3 (Voltage Flicker) CE Declaration of Conformity GS Certification - EN60950-1 International Japan CB Certification - IEC60950-1 CISPR 22 / CISPR 24 VCCI Certification None Required 88 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 107
    Russia Ukraine Taiwan GOST-R 50377-92 Certification GOST R 29216-91 (Emissions) GOST R 50628-95 (Immunity) Ukraine Certification BSMI CNS13438 CPU-SR1690(A) MO04 None Required R33025 Intel® Server System SR1690WB Service Guide 89
  • Intel SR1690WB | Service Guide - Page 108
    related to the EMC performance of this product, contact: Intel Corporation 5200 N.E. Elam Young Parkway Hillsboro, OR 97124-6497 if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 109
    . If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Intel® Server System SR1690WB Service Guide 91
  • Intel SR1690WB | Service Guide - Page 110
    side (pedestal orientation) or side (rack mount configuration). The BSMI Certification Marking and EMC warning is located on the outside rear area of the product. KCC (Korea) Following is the KCC certification information for Korea. CPU-SR1690 (A) 92 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 111
    installed in a Restricted Access Location in accordance with articles 110-16, 110-17, and 110-18 of the National Electric Code, ANSI/NFPA 70. The DC source must be electrically isolated by double or reinforced insulation from any hazardous AC source. Intel® Server System SR1690WB Service Guide 93
  • Intel SR1690WB | Service Guide - Page 112
    connectors that plug into the AC receptacle on the server must be an approved IEC (International Electrotechnical Commission) 320, sheet C13, type female connector. • Cord length and flexibility: Cords must be less than 4.5 meters (14.76 feet) long. 94 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 113
    All materials, parts and subassemblies must not contain restricted materials as defined in Intel's Environmental Product Content Specification of Suppliers and Outsourced Manufacturers - http:// supplier.intel.com/ehs/ environmental.htm None Required Intel® Server System SR1690WB Service Guide 95
  • Intel SR1690WB | Service Guide - Page 114
    's Environmental Product Content Specification of Suppliers and Outsourced Manufacturers - http:// supplier.intel.com/ehs/ environmental.htm None Required ISO11469 - Plastic parts weighing >25gm are intended to be marked with per ISO11469. >PC/ABS< 96 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 115
    Recycling Markings - Fiberboard (FB) and Cardboard (CB) are marked with international recycling marks. Applied to outer bulk packaging and single package. Compliance Reference Marking Example Intel® Server System SR1690WB Service Guide 97
  • Intel SR1690WB | Service Guide - Page 116
    power supply cords before servicing. Simplified Chinese: 2 Traditional Chinese: 2 German: Dieses Geräte hat mehr als ein Stromkabel. Um eine Gefahr des elektrischen Schlages zu verringern trennen sie beide (2) Stromkabeln bevor Instandhaltung. 98 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 117
    for the region in which it is sold. • Peripheral Storage Devices: must be a UL recognized or UL listed accessory and TUV or VDE licensed. Total server configuration is not to exceed the maximum loading conditions of the power supply. Intel® Server System SR1690WB Service Guide 99
  • Intel SR1690WB | Service Guide - Page 118
    End-of-Life / Product Recycling Product recycling and end-of-life take-back systems and requirements vary by country. Contact the retailer or distributor of this product for information about product recycling and / or take-back. 100 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 119
    Product by means of hardware and/or software; OR • REPLACE the Product with another Product; OR • REFUND the then-current value of the Product if Intel is unable to repair or replace the Product. If such Product is defective, transportation charges for the return of Product to buyer within the USA
  • Intel SR1690WB | Service Guide - Page 120
    causes, including accident, problems with electrical power, usage not in accordance with product instructions, misuse, neglect, alteration Service To obtain warranty service for this Product, you may contact Intel or your authorized distributor. 102 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 121
    :// www.intel.com/), call your local distributor or an Intel Customer Support representative. See "Getting Help" for telephone numbers. Returning a Defective Product Before returning any product, call your authorized dealer/distribution authority. Intel® Server System SR1690WB Service Guide 103
  • Intel SR1690WB | Service Guide - Page 122
    104 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 123
    : http://support.intel.com/support/motherboards/server/sb/cs-010770.htm English SAFETY STEPS: Whenever you remove the chassis covers to access the inside of the system, follow these steps: 1. Turn off all peripheral devices connected to the system. 2. Turn off the system by pressing the power button
  • Intel SR1690WB | Service Guide - Page 124
    möglicherweise erhitzt, wenn das System in Betrieb ist. Außerdem können einige Platinen und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie sollten Schutzhandschuhe tragen. 106 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 125
    instruction. Consultez Intel Server Boards and Server Chassis Safety Information sur le CD Resource CD ou bien rendez-vous sur le site: http://support.intel.com/support/motherboards/server/sb . Nous vous recommandons l'usage de gants de protection. Intel® Server System SR1690WB Service Guide 107
  • Intel SR1690WB | Service Guide - Page 126
    cortantes o punzantes. Por ello, se recomienda precaución y el uso de guantes protectores. Resource CD http://support.intel.com/support/motherboards/server/sb/cs010770.htm 上的 Intel Server Boards and Server Chassis Safety Information（《Intel 108 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 127
    dissipatore di calore potrebbero essere surriscaldati. Fare attenzione alla presenza di piedini appuntiti e parti taglienti sulle schede e sul telaio. È consigliabile l'uso di guanti di protezione. Intel® Server System SR1690WB Service Guide 109
  • Intel SR1690WB | Service Guide - Page 128
    110 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 129
    all warnings and precautions in this guide before installing or maintaining your Intel® Server Product. In the event of server should be integrated and serviced only by technically qualified persons. You must adhere to the guidelines in this guide and the assembly instructions in your server manuals
  • Intel SR1690WB | Service Guide - Page 130
    outlet. • Provided with sufficient space to access the power supply cord(s), because they serve as the product's main power disconnect. Equipment Handling Practices Reduce the risk of for easier handling, remove any easily detachable components. 112 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 131
    Stromschlags hin, der bei Nichtbeachtung der Sicherheitshinweise zu schweren oder tödlichen Verletzungen führen kann. Weist auf Verbrennungsgefahr an heißen Bauteilen bzw. Oberflächen hin. Intel® Server System SR1690WB Service Guide 113
  • Intel SR1690WB | Service Guide - Page 132
    Geräte erzeugt werden. • In gewittergefährdeten Gebieten sollten Sie das System an einen Überspannungsschutz anschließen und bei einem Gewitter die Telekommunikationskabel zum lassen, um das Gewicht zu reduzieren und die Handhabung zu erleichtern. 114 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 133
    äts vom Stromnetz. Die Steckdose muß in der Nähe der Anlage angebracht und gut erreichbar sein. • Netzkabel müssen an eine ordnungsgemäß geerdete Steckdose angeschlossen sein. Intel® Server System SR1690WB Service Guide 115
  • Intel SR1690WB | Service Guide - Page 134
    , und bauen Sie das schwerste Gerät an der untersten Position im Rack ein. Ziehen Sie jeweils immer nur ein Gerät aus dem Rack heraus. 116 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 135
    aus dem Server mit der Bauelementseite Systems ohne Abdeckung kann zur Beschädigung von Systemkomponenten führen. So bringen Sie die Abdeckung wieder an: • Vergewissern Sie sich zunächst, daß Sie keine Werkzeuge oder Teile im Gehäuse vergessen haben. Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 136
    sur le serveur Ce document s'applique aux cartes serveur Intel®, au châssis de serveur Intel® (sur pieds et sur rack) et aux és. Vous devez suivre les informations de ce guide et les instructions d'assemblage des manuels de serveur pour vérifier . 118 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 137
    du soleil et les radiateurs. • À l'écart des sources de vibration ou des chocs physiques. • Isolé des champs électromagnétiques importants produits par des appareils électriques. Intel® Server System SR1690WB Service Guide 119
  • Intel SR1690WB | Service Guide - Page 138
    les débrancher avant d'ouvrir le châssis, d'ajouter ou de supprimer un composant non connectable à chaud. Les alimentations de certains serveurs Intel sont munies de doubles fusibles pôle/ bloc d'alimentation. L'intérieur de celui-ci est soumis à des 120 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 139
    Les cordons d'alimentation doivent répondre aux critères suivants : - Le cordon d'alimentation doit supporter une intensité supérieure à celle indiquée sur le produit. - Le cordon d'alimentation doit de télécommunication qui sont connectés au système. Intel® Server System SR1690WB Service Guide 121
  • Intel SR1690WB | Service Guide - Page 140
    le montage en rack Le rack doit être fixé à un support inamovible pour éviter qu'il ne bascule lors de l'extension d'un l'équipement. Le rack doit être installé conformément aux instructions du fabricant. Installez les équipements dans le rack en partant du Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 141
    les ESD en portant un bracelet antistatique relié à la masse du châssis (n'importe quelle surface métallique non peinte) de votre serveur lorsque que vous manipulez installés. • Fixez les panneaux au châssis en suivant les instructions du produit. Intel® Server System SR1690WB Service Guide 123
  • Intel SR1690WB | Service Guide - Page 142
    ceñirse a las directrices de esta guía y a las instrucciones de montaje de los manuales del servidor para asegurar y mantener el cumplimiento con las certificaciones y homologaciones existentes de los graves si no se tiene en cuenta la ADVERTENCIA. 124 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 143
    correctamente conectada a tierra. • Provista de espacio suficiente para acceder a los cables de la fuente de alimentación ya que constituyen la desconexión principal de la alimentación. Intel® Server System SR1690WB Service Guide 125
  • Intel SR1690WB | Service Guide - Page 144
    conexión en funcionamiento. Algunas fuentes de alimentación de electricidad de los servidores de Intel utilizan el polo neutral del fuselaje. Para evitar riesgos de choques electricos use precaució adquiera alguno cuyo uso esté aprobado en su país. 126 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 145
    fabricante para repararla. • Apague el servidor y desconecte todos los cables de alimentación antes de agregar o reemplazar cualquier componente que no es de conexión en funcionamiento. Intel® Server System SR1690WB Service Guide 127
  • Intel SR1690WB | Service Guide - Page 146
    el riesgo de descargas eléctricas, deberá instalar una conexión a tierra apropiada para el bastidor y para cada pieza del equipo instalada en el mismo. 128 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 147
    del equipo. Deseche las baterías respetando la normativa local. No intente recargar la batería. No intente desmontar, pinchar o causar cualquier otro desperfecto a una batería. Intel® Server System SR1690WB Service Guide 129
  • Intel SR1690WB | Service Guide - Page 148
    de ningún periférico o dispositivo láser • Los periféricos o dispositivos láser no pueden ser reparados por el usuario • Haga que el fabricante los repare 130 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 149
    简体中文 Intel Intel Intel Web UL 注意 警告 Intel® Server System SR1690WB Service Guide 131
  • Intel SR1690WB | Service Guide - Page 150
    ITE ITE 场地选择 5V 132 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 151
    Intel® Server System SR1690WB Service Guide 133
  • Intel SR1690WB | Service Guide - Page 152
    ESD) ESD ESD ESD ESD 134 Intel® Server System SR1690WB Service Guide
  • Intel SR1690WB | Service Guide - Page 153
    其他危险 替换电池 Intel® Server System SR1690WB Service Guide 135
  • Intel SR1690WB | Service Guide - Page 154
    136 Intel® Server System SR1690WB Service Guide
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Intel® Server System SR1690WB
Service Guide
A Guide for Technically Qualified Assemblers of Intel
®
Identified Subassemblies/
Products
Intel Order Number E78186-004