Intel SR2400SYSD2 User Guide

Intel SR2400SYSD2 - Server System - 0 MB RAM Manual

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Intel SR2400SYSD2 manual content summary:

  • Intel SR2400SYSD2 | User Guide - Page 1
    Intel® Server Chassis SR2400/SR2400DC User Guide Order Number: C51501-003
  • Intel SR2400SYSD2 | User Guide - Page 2
    required for their specific application and environmental conditions. Intel Corporation can not be held responsible if components fail or the server board does not operate correctly when used outside any of their published operating or nonoperating limits. Intel, Intel Pentium, and Intel Xeon are
  • Intel SR2400SYSD2 | User Guide - Page 3
    and Platforms: Intel® Server Board SE7520JR2 Intel® Server Board SE7320VP2 Intel® Server Platform SR2400SYS (integrated system) Intel® Server Platform SR2400SYSD2 (integrated system) 1 For complete technical specifications and additional technical information, see the Intel® Server Chassis SR2400
  • Intel SR2400SYSD2 | User Guide - Page 4
    the Intel Server Chassis SR2400/SR2400DC. This list does not include items that are shipped and pre-installed in the Intel Server Platform SR2400JR2. 3 Before purchasing any required options, refer to your server board documentation to determine which option(s) are supported on your server board
  • Intel SR2400SYSD2 | User Guide - Page 5
    brackets to mount the server into a rack Cable management arm Front bezel for the selected control panel option Processor(s) and heat sink(s) Memory DIMMs Intel® Management Module (Advanced or Professional) Tape drive kit Redundant fan kit (includes four fans) Redundant power supply Sixth drive SCSI
  • Intel SR2400SYSD2 | User Guide - Page 6
    with this server board, use the following resources. These sources are available at http://support.intel.com/support/motherboards/server/chassis/SR2400/ Unless Specification If you just received this product and Quick Start User's Guide in the product box need to install it For virtual system
  • Intel SR2400SYSD2 | User Guide - Page 7
    on the chassis earth-ground studs should be installed with a 10 in/lb torque. The safety ground conductor provides proper grounding only for the system. You must provide additional proper grounding for the rack and other devices installed in it. Intel® Server Chassis SR2400/SR2400DC User Guide vii
  • Intel SR2400SYSD2 | User Guide - Page 8
    power, telephone, and communication cables. Turn off the server and disconnect the power cord, telecommunications systems, networks, and modems attached to the server can damage the contacts inside the jumper, causing intermittent problems with the function controlled by that jumper. Take care to
  • Intel SR2400SYSD2 | User Guide - Page 9
    in this document before performing any of the instructions. See also Intel Server Boards and Server Chassis Safety Information at http://support.intel.com/support/motherboards/server/sb/CS-010770.htm. The power supply in this product contains no user-serviceable parts. There may be more than one
  • Intel SR2400SYSD2 | User Guide - Page 10
    according to manufacturer's instructions. The system is designed to operate system into a surge suppresser and disconnect telecommunication lines to your modem during an electrical storm. Provided with a properly grounded wall outlet. Provided with sufficient space to access the power supply
  • Intel SR2400SYSD2 | User Guide - Page 11
    und Servergehäusen unter http://support.intel.com/support/motherboards/server/sb/CS-010770.htm. Benutzer Systems, falls eine Verschlußeinrichtung installiert ist. 2. Entfernen Sie alle Schrauben der Gehäuseabdeckung. 3. Nehmen Sie die Abdeckung ab. Intel® Server Chassis SR2400/SR2400DC User Guide
  • Intel SR2400SYSD2 | User Guide - Page 12
    oder Teile darin beschädigen. Um die Abdeckung wieder anzubringen: 1. Vergewissern Sie sich, daß Sie keine Werkzeuge oder Teile im Innern des Systems zurückgelassen haben. 2. Überprüfen Sie alle Kabel, Zusatzkarten und andere Komponenten auf ordnungsgemäßen Sitz und Installation. 3. Bringen Sie die
  • Intel SR2400SYSD2 | User Guide - Page 13
    ce document avant de suivre toute instruction. Consultez Intel Server Boards and Server Chassis Safety Information sur le site http://support.intel.com/support/motherboards/server/sb/CS-010770.htm. Le système tandis que le boîtier est ouvert. Intel® Server Chassis SR2400/SR2400DC User Guide xiii
  • Intel SR2400SYSD2 | User Guide - Page 14
    Remplacer uniquement avec une batterie du même type ou d'un type équivalent recommandé par le fabricant. Disposez des piles usées selon les instructions du fabricant. Le système a été conçu pour fonctionner dans un cadre de travail normal. L'emplacement choisi doit être: Propre et dépourvu de poussi
  • Intel SR2400SYSD2 | User Guide - Page 15
    cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety Information en en http://support.intel.com/support/motherboards/server/sb/CS-010770.htm. El usuario guarde todos los tornillos de las tapas. 3. Extraiga las tapas. Intel® Server Chassis SR2400/SR2400DC User Guide xv
  • Intel SR2400SYSD2 | User Guide - Page 16
    Para obtener un enfriamiento y un flujo de aire adecuados, reinstale siempre las tapas del chasis antes de poner en marcha el sistema. Si pone en funcionamiento el sistema sin las tapas bien colocadas puede dañar los componentes del sistema. Para instalar las tapas: 1. Asegúrese primero de no haber
  • Intel SR2400SYSD2 | User Guide - Page 17
    . 4. Inserire e chiudere a chiave il lucchetto sul retro del sistema per impedire l'accesso non autorizzato al sistema. 5. Ricollegare tutti i cavi esterni e le prolunghe AC del sistema. Intel® Server Chassis SR2400/SR2400DC User Guide xvii
  • Intel SR2400SYSD2 | User Guide - Page 18
    Se il sistema è stato a lungo in funzione, il microprocessore e il dissipatore di calore potrebbero essere surriscaldati. Fare attenzione alla presenza di piedini appuntiti e parti taglienti sulle schede e sul telaio. È consigliabile l'uso di guanti di protezione. Esiste il pericolo di un esplosione
  • Intel SR2400SYSD2 | User Guide - Page 19
    Drive Air Baffle (No Backplane Installed 27 Removing and Installing the Fan Module 28 Removing the Fan Module 28 Installing the Fan Module 29 Installing and Removing a Hard Disk Drive 31 Removing a SATA or SCSI Hot-swap Hard Disk Drive 31 Intel® Server Chassis SR2400/SR2400DC User Guide xix
  • Intel SR2400SYSD2 | User Guide - Page 20
    95 Power Supply Specifications 95 700-W Redundant Power Supply Input Voltages (AC Version only 95 700-W Single Power Supply Output Voltages 95 600-W Redundant Power Supply Input Voltage (DC Version only 95 600-W Single Power Supply Output Voltages 96 System Environmental Specifications 96
  • Intel SR2400SYSD2 | User Guide - Page 21
    Limitations and Exclusions 114 Limitations of Liability 114 How to Obtain Warranty Service 115 Telephone Support...115 Returning a Defective Product 115 Figures Figure 1. Intel® Server Chassis SR2400/SR2400DC 1 Figure 2. Internal Component Locations 4 Figure 3. Rear of SATA Backplane 5 Figure
  • Intel SR2400SYSD2 | User Guide - Page 22
    Control Panel from the Chassis 70 Figure 62. Installing a System Fan 71 Figure 63. Disconnecting the Flex Cable from the Server Board 73 Figure 64. Disconnecting the Power Cables from the Server Board 74 Figure 65. Disconnecting the Power Cable from the Backplane 74 Figure 66. Disconnecting the
  • Intel SR2400SYSD2 | User Guide - Page 23
    the Chassis 91 Figure 83. Connecting the Tape Drive Cables 92 Figure 84. Installing the Filler Panels 93 Tables Table 1. Table 2. Table 3. Server Chassis Features 2 Product Certification Markings 102 Product Certification Markings 103 Intel® Server Chassis SR2400/SR2400DC User Guide xxiii
  • Intel SR2400SYSD2 | User Guide - Page 24
    xxiv
  • Intel SR2400SYSD2 | User Guide - Page 25
    of the server features, and diagrams showing the location of important components and connections on the server chassis. The Intel® Server Chassis SR2400/SR2400DC is shown in the following picture. Figure 1. Intel® Server Chassis SR2400/SR2400DC Intel® Server Chassis SR2400/SR2400DC User Guide 1
  • Intel SR2400SYSD2 | User Guide - Page 26
    features of the server chassis.6 Table 1. Server Chassis Features Fans (dependent on option selected) Support for up to eight system fans (four standard, four as optional accessory) Two non-redundant fans in power supply Control Panel (dependent on option selected) Standard Control Panel Intel
  • Intel SR2400SYSD2 | User Guide - Page 27
    video port (available only with the Standard Control Panel)7 One rear panel video port 7 Video connections must be used separately. The server board and chassis do not support synchronous use of video out of the front and back of the chassis. Intel® Server Chassis SR2400/SR2400DC User Guide 3
  • Intel SR2400SYSD2 | User Guide - Page 28
    TP01087 A. Power supply module housing F. Fan module (shown with optional redundant fans) B. Power distribution module G. SATA or SCSI backplane (optional component) C. PCI Riser assembly H. Drive bay area (drives not included) D. Processor air duct. (Memory DIMMs and processor(s) underneath
  • Intel SR2400SYSD2 | User Guide - Page 29
    SATA backplane. The power supply, server board and a Fan distribution cable connector B. OPT connector E. Flex cable connector C. Location for sixth drive board (accessory) F. Backplane power connector Figure 4. Rear of SCSI Backplane TP01364 Intel® Server Chassis SR2400/SR2400DC User Guide
  • Intel SR2400SYSD2 | User Guide - Page 30
    the Intel® Local Control Panel. For instructions on installing the Standard Control Panel, see "Replacing the Control Panel." AB C D EF G H I Callout A B C D E F G H I J K L Feature NIC 2 activity LED NIC 1 activity LED Power/Sleep button Power/Sleep LED Hard disk drive activity LED System Fault
  • Intel SR2400SYSD2 | User Guide - Page 31
    system has power applied to it. Blinking green indicates the system is in S1 sleep state. No light indicates the power is off / is in ACPI S4 or S5 state. Toggles the system power on/off. Sleep button for ACPI-compatible operating systems. Continued Intel® Server Chassis SR2400/SR2400DC User Guide
  • Intel SR2400SYSD2 | User Guide - Page 32
    the system. Figure 6. Intel® Local Control Panel Back Panel Features A B C D F A. Low-profile add-in card bracket B. Full-height add-in card bracket C. Grounding studs E AF00638 D. AC power receptacles (top receptacle for optional redundant power supply) E. Power supply fans (shown
  • Intel SR2400SYSD2 | User Guide - Page 33
    Removing a Hard Disk Drive." ✏ NOTES Drives can consume up to 17 watts of power each. Drives must be specified to run at a maximum ambient temperature of 45°C. The Intel Server Chassis SR2400/SR2400DC does not support all SCSI or Serial ATA hard drives. See "Additional Information and Software" for
  • Intel SR2400SYSD2 | User Guide - Page 34
    instructions for a CD-ROM or DVD-ROM drive, see "Installing or Removing a CD-ROM or DVDROM Drive." ✏ NOTES The optional kit to convert a hard drive bay to a floppy drive bay must be used if both a CD-ROM / DVD-ROM drive and a floppy drive are needed. The Intel Server Chassis SR2400 does not support
  • Intel SR2400SYSD2 | User Guide - Page 35
    , see the instructions provided with the management module. ✏ NOTE Some server boards may not support the Intel® Management Module. See your server board documentation to determine if this feature is compatible with your server board. Rack-Mounted Systems Your Server Chassis SR2400 is designed to
  • Intel SR2400SYSD2 | User Guide - Page 36
    12
  • Intel SR2400SYSD2 | User Guide - Page 37
    this manual. See "Safety Information." This document provides instructions for adding and replacing chassis components. For instructions on replacing components on the server board, such as the processor and memory DIMMs, see the instructions provided with the server board. Tools and Supplies Needed
  • Intel SR2400SYSD2 | User Guide - Page 38
    the Chassis Cover The Intel® Server Chassis SR2400/SR2400DC must be operated with the top cover in place to ensure proper cooling. You will need to remove the top cover to add or replace components inside of the chassis. Before removing the top cover, power down the server and unplug all peripheral
  • Intel SR2400SYSD2 | User Guide - Page 39
    below. 3. (Optional): Insert the shipping screw at the center of the top cover. See letter "B" in the figure. 4. Reconnect all peripheral devices and the AC power cord or DC external source. A B Figure 10. Installing the Chassis Cover Intel® Server Chassis SR2400/SR2400DC User Guide 15
  • Intel SR2400SYSD2 | User Guide - Page 40
    Server Chassis SR2400. Two front bezel options are available. One is used for the Standard Control Panel and the other is used with the Intel® Bezel Use the steps below if your system includes either the standard front bezel or the front bezel for the Intel Local Control Panel. 1. Unlock the bezel
  • Intel SR2400SYSD2 | User Guide - Page 41
    Installing the Front Bezel Use the steps below if your system includes either the standard front bezel or the front bezel for the Intel Local Control Panel. The front bezel is optional. 1. bezel. Figure 12. Installing the Front Bezel TP01342 Intel® Server Chassis SR2400/SR2400DC User Guide 17
  • Intel SR2400SYSD2 | User Guide - Page 42
    of the processors. For instructions on adding or replacing a processor, first remove the processor air duct and the processor air dam, and then see your server board user guide for instructions on processor installations and removals. Return to these instructions to reinstall the processor air dam
  • Intel SR2400SYSD2 | User Guide - Page 43
    duct. TP01116 Figure 14. Installing the Processor Air Duct 7. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 8. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. Intel® Server Chassis SR2400/SR2400DC User Guide 19
  • Intel SR2400SYSD2 | User Guide - Page 44
    see your server board user guide for instructions on processor installations and removals. Return to these instructions to reinstall the processor air dam and the processor air duct. 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the
  • Intel SR2400SYSD2 | User Guide - Page 45
    of the server chassis. If your system uses fixed drives, you have one air baffle that is attached between the power supply and the drive server chassis with the air baffle(s) in place. Air baffles are required for proper airflow within the chassis. Intel® Server Chassis SR2400/SR2400DC User Guide
  • Intel SR2400SYSD2 | User Guide - Page 46
    and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Important: Note how the cables are
  • Intel SR2400SYSD2 | User Guide - Page 47
    Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Lower the baffle into the chassis between the power supply Intel® Server Chassis SR2400/SR2400DC User Guide 23
  • Intel SR2400SYSD2 | User Guide - Page 48
    2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see 5. Remove the fan module. For instructions, see "Removing the Fan Module." 6. Remove the SATA or SCSI backplane. For instructions, see "Removing
  • Intel SR2400SYSD2 | User Guide - Page 49
    the backplane. For instructions, see "Installing a Replacement SATA or SCSI Backplane." 9. Install the fan module. For instructions, see "Installing the Fan Module." 10. Return to the procedure that directed you to install the small air baffle. Intel® Server Chassis SR2400/SR2400DC User Guide 25
  • Intel SR2400SYSD2 | User Guide - Page 50
    and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Important: Note how the cables are
  • Intel SR2400SYSD2 | User Guide - Page 51
    down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Hook the front of the air baffle under the drive bay area at the left of the fan module, engaging the two small hooks
  • Intel SR2400SYSD2 | User Guide - Page 52
    of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Disconnect the fan module cable from the fan module. 5. Pull up on the
  • Intel SR2400SYSD2 | User Guide - Page 53
    instructions, see "Removing the Chassis Cover." 4. (For hot-swap system only): Attach the fan distribution cable between the backplane and the fan module. See letters "A" and "B" in the figure below. B A TP01080 Figure 23. Connecting the Fan Distribution Cable Intel® Server Chassis SR2400/SR2400DC
  • Intel SR2400SYSD2 | User Guide - Page 54
    and slide the module to the right until the blue tab clicks into place. See letter "A" in the figure below. 6. Connect the folded fan module ribbon cable to the fan module. See letter "B" in the figure. 7. If it is not already connected, connect the other end of the ribbon cable to the
  • Intel SR2400SYSD2 | User Guide - Page 55
    Intel Server Chassis SR2400 does not support all hard drives. See "Additional Information and Software" for an Internet link to a list of supported hardware. Removing a SATA or SCSI Hot-swap Hard Disk Drive Use these instructions from the Chassis Intel® Server Chassis SR2400/SR2400DC User Guide 31
  • Intel SR2400SYSD2 | User Guide - Page 56
    drive from its wrapper and place it on an antistatic surface. 2. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions. 3. With the drive circuit-side down, position the connector end of the drive so that it is facing the rear of the drive carrier. 4. Align
  • Intel SR2400SYSD2 | User Guide - Page 57
    to lock the drive assembly into place. See letter "B" in the figure. A B TP00789 Figure 28. Inserting a Hot-swap Hard Disk Drive Assembly into the Chassis Intel® Server Chassis SR2400/SR2400DC User Guide 33
  • Intel SR2400SYSD2 | User Guide - Page 58
    1. See letter "C" in the figure below to identify the end of the SATA cable that is attached to the server board. See your server board documentation to locate the SATA connection points on the server board. If you will be using an add-in SATA RAID controller, connect SATA CH A through SATA CH
  • Intel SR2400SYSD2 | User Guide - Page 59
    below. See your server board documentation to locate the SCSI connection point on the server board. B A TP01075 Figure 30. Connecting the SCSI Data Cable 11. (Optional) Install the front bezel. For instructions, see "Installing the Front Bezel." Intel® Server Chassis SR2400/SR2400DC User Guide 35
  • Intel SR2400SYSD2 | User Guide - Page 60
    instructions only if you have installed the fixed drive kit. CAUTION Fixed drives are NOT hot swappable. Before removing or replacing the drive, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button
  • Intel SR2400SYSD2 | User Guide - Page 61
    the hard drive to the carrier using the four screws removed from the carrier. A TP00788 Figure 33. Attaching a Hard Drive to the Fixed Drive Carrier Intel® Server Chassis SR2400/SR2400DC User Guide 37
  • Intel SR2400SYSD2 | User Guide - Page 62
    the easiest cable routing. 10. If it is not already installed, connect the SATA power cable adapter to the 3x2 power supply cable that extends from your power supply. See letters "A" and "B" in the figure below. The power cable adapter was provided to you with the fixed drive kit. B A TP01161 Figure
  • Intel SR2400SYSD2 | User Guide - Page 63
    the figure below. A B D C A * Air baffle for AC model shown; air baffle for DC model differs. Figure 35. Installing the Fixed SATA Drive Data Cables TP01324 Intel® Server Chassis SR2400/SR2400DC User Guide 39
  • Intel SR2400SYSD2 | User Guide - Page 64
    the air baffle. See letter "B" in the figure below. The power cables for drives installed to the left of the air baffle do 17. Install the chassis cover. For instructions, see "Removing the Chassis Cover." 18. Install the front bezel. For instructions, see "Removing and Installing the Front Bezel
  • Intel SR2400SYSD2 | User Guide - Page 65
    For instructions, see "Removing and Installing the Front Bezel." 12. Install the chassis cover. For instructions, see "Removing the Chassis Cover." 13. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. Intel® Server Chassis SR2400/SR2400DC User Guide
  • Intel SR2400SYSD2 | User Guide - Page 66
    and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the front bezel if it is
  • Intel SR2400SYSD2 | User Guide - Page 67
    Hardware Installations and Upgrades 6. Remove the fan module. For instructions, see "Removing the Fan Module." 7. Hold the SATA or SCSI sixth drive accessory board in locating connectors on the backplane, see "HotSwap SCSI Backplane Connections." Intel® Server Chassis SR2400/SR2400DC User Guide 43
  • Intel SR2400SYSD2 | User Guide - Page 68
    are following the correct instructions for your server. CAUTION Floppy drives are NOT hot swappable. Before removing or replacing the drive, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and
  • Intel SR2400SYSD2 | User Guide - Page 69
    Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the place. See letter "C" in the figure. C A B Intel® Server Chassis SR2400/SR2400DC User Guide TP01144 45
  • Intel SR2400SYSD2 | User Guide - Page 70
    the Chassis 14. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 15. (Optional): Install the front bezel. For instructions, see "Installing the Front Bezel." 16. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. 46
  • Intel SR2400SYSD2 | User Guide - Page 71
    For instructions, see "Installing the Chassis Cover." 13. (Optional): Install the front bezel. For instructions, see "Installing the Front Bezel." 14. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. Intel® Server Chassis SR2400/SR2400DC User Guide
  • Intel SR2400SYSD2 | User Guide - Page 72
    carrier for the slimline floppy drive that is used in these instructions was sent to you in the hardware kit that came with your Server Chassis SR2400/2400DC. The interposer board and floppy drive power adapter cable used in these instructions was sent to you with your fixed drive kit. 1. Observe
  • Intel SR2400SYSD2 | User Guide - Page 73
    on the connector cover to lock the cable into place. See letter "F" in the figure. Figure 43. Connecting the Flat Flex Cable to a Floppy Drive Intel® Server Chassis SR2400/SR2400DC User Guide 49
  • Intel SR2400SYSD2 | User Guide - Page 74
    13. Lower the interposer board into the floppy drive tray at the rear of the floppy drive and engage the notch on the board. See letter "A" in the figure below. 14. Attach the interposer board to floppy drive with the screw that was included with the interposer board. See letter "B" in the figure.
  • Intel SR2400SYSD2 | User Guide - Page 75
    16. Connect the 2x2 end of the floppy drive power cable that was included with your kit to the 2x2 power connector on the SATA power adapter cable. See letters "B" and "C" in the E DE D F B C Figure 45. Connecting the Floppy Drive Cables TP01165 Intel® Server Chassis SR2400/SR2400DC User Guide 51
  • Intel SR2400SYSD2 | User Guide - Page 76
    and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the front bezel if it is
  • Intel SR2400SYSD2 | User Guide - Page 77
    drive conversion kit can only be installed into a system that is using either the SATA or the SCSI Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions Intel® Server Chassis SR2400/SR2400DC User Guide 53
  • Intel SR2400SYSD2 | User Guide - Page 78
    7. Slide the floppy drive into the drive carrier, rear of the drive first, with the underside of the drive facing down. 8. Line up the holes in the side of the drive with the holes in the carrier. See letter "A" in the figure below. A A TP01308 Figure 47. Inserting a Floppy Drive into the Floppy
  • Intel SR2400SYSD2 | User Guide - Page 79
    the connector cover to lock the cable into place. See letter "C" in the figure. C A B TP01311 Figure 50. Connecting the Flat Flex Cable to a Floppy Drive Intel® Server Chassis SR2400/SR2400DC User Guide 55
  • Intel SR2400SYSD2 | User Guide - Page 80
    Chassis TP01310 18. Install the chassis cover. For instructions, see "Installing the Chassis Cover" 19. (Optional) Install the front bezel. For instructions, see "Installing the Front Bezel." 20. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. 56
  • Intel SR2400SYSD2 | User Guide - Page 81
    drive, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and remove the AC power cord or DC external source from the system or wall outlet. Intel® Server Chassis SR2400/SR2400DC User Guide 57
  • Intel SR2400SYSD2 | User Guide - Page 82
    bay of your Server Chassis SR2400/SR2400DC. 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see
  • Intel SR2400SYSD2 | User Guide - Page 83
    See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis release the drive from the drive carrier. Intel® Server Chassis SR2400/SR2400DC User Guide 59
  • Intel SR2400SYSD2 | User Guide - Page 84
    the slimline DVD-ROM drive / CD-ROM drive was preinstalled in the slimline drive bay of your Server Chassis SR2400/SR2400DC. The interposer board and floppy drive power adapter cable used in these instructions was sent to you with your fixed drive kit. 1. Observe the safety and ESD precautions at
  • Intel SR2400SYSD2 | User Guide - Page 85
    instructions, see "Installing the Chassis Cover." 15. (Optional) Install the front bezel. For instructions, see "Installing the Front Bezel." 16. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. Intel® Server Chassis SR2400/SR2400DC User Guide 61
  • Intel SR2400SYSD2 | User Guide - Page 86
    and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the front bezel if it is
  • Intel SR2400SYSD2 | User Guide - Page 87
    source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the processor air duct. For instructions, see "Removing the Processor Air Duct" 5. Disconnect any cables attached to any installed add-in cards. Intel® Server Chassis SR2400/SR2400DC User Guide 63
  • Intel SR2400SYSD2 | User Guide - Page 88
    See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the processor air duct. For instructions, see "Removing the Processor Air Duct
  • Intel SR2400SYSD2 | User Guide - Page 89
    the instructions under "Installing the PCI Riser Assembly" to install a new riser connector. NOTE To eliminate the possibility of installing the replacement connectors on the wrong side of the PCI riser assembly, replace one connector at a time. Intel® Server Chassis SR2400/SR2400DC User Guide 65
  • Intel SR2400SYSD2 | User Guide - Page 90
    . See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove processor air duct. For instructions, see "Removing the Processor Air Duct
  • Intel SR2400SYSD2 | User Guide - Page 91
    . For instructions, see "Installing the PCI Riser Assembly." 13. Install the processor air duct. For instructions, see "Installing the Processor Air Duct." 14. Install the chassis cover. For instructions, see "Installing the Chassis Cover." Intel® Server Chassis SR2400/SR2400DC User Guide 67
  • Intel SR2400SYSD2 | User Guide - Page 92
    See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the processor air duct. For instructions, see "Removing the Processor Air Duct
  • Intel SR2400SYSD2 | User Guide - Page 93
    See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the processor air duct. For instructions, see "Removing the Processor Air Duct
  • Intel SR2400SYSD2 | User Guide - Page 94
    positioned differently for the Intel® Local Control Panel instructions, see "Installing the Chassis Cover." 12. (Optional) Install the front bezel. For instructions, see "Installing the Front Bezel." 13. Plug in all peripheral devices and connect the AC power cable or DC external source to the server
  • Intel SR2400SYSD2 | User Guide - Page 95
    power supply module must be replaced. To replace a system fan, use the following instructions. To install the redundant fans, use the following instructions, but disregard step 4. CAUTION Fans are NOT hot swappable. Before removing or replacing a fan, you must first take the server out of service
  • Intel SR2400SYSD2 | User Guide - Page 96
    only applies to the AC version of the Intel® Server Chassis SR2400. If you are replacing a power distribution module for the Intel® Server Chassis SR2400DC, see "Replacing the Power Supply Distribution Module (DC Version)" for instructions. The power supply distribution module is at the front of the
  • Intel SR2400SYSD2 | User Guide - Page 97
    cable from the server board. See letter "A" in the figure below. The position of your cable may be different. See your server board documentation for the specific connection point. A Figure 63. Disconnecting the Flex Cable from the Server Board Intel® Server Chassis SR2400/SR2400DC User Guide 73
  • Intel SR2400SYSD2 | User Guide - Page 98
    diagram below, letter "A" shows the main power cable, letter "B" shows the power signal cable, and letter "C" shows the CPU power cable. B A C Figure 64. Disconnecting the Power Cables from the Server Board 9. (Hot-swap system only): Disconnect the 2x3 power cable from the backplane. See the figure
  • Intel SR2400SYSD2 | User Guide - Page 99
    system only): Disconnect the SATA power adapter cable from the power supply. In the figure below, letter "B" is the connector from the power supply. Letter "A" is the connector from the SATA power Figure 67. Removing the Power Distribution Module Intel® Server Chassis SR2400/SR2400DC User Guide 75
  • Intel SR2400SYSD2 | User Guide - Page 100
    . (Hot-swap system only): Connect the flex cable to the server. Refer back to Figure 63 and see your server board documentation to locate the connection points for this cable. 19. Install the hot-swap power supply/supplies. For instructions, see "Installing a Hot-swap Power Supply." 20. Install the
  • Intel SR2400SYSD2 | User Guide - Page 101
    . For instructions, see "Installing the Processor Air Duct." 22. Install the chassis cover. For instructions, see "Installing the Chassis Cover." Replacing the Power Supply Distribution Module (DC Version) ✏ NOTE This procedure only applies to the DC version of the Intel® Server Chassis SR2400. If
  • Intel SR2400SYSD2 | User Guide - Page 102
    -swap system only) Disconnect the backplane flat flex cable from the server board. See letter "A" in the figure below. The position of your cable may be different. See your server board documentation for the specific connection point. A Figure 69. Disconnecting the Flex Cable from the Server Board
  • Intel SR2400SYSD2 | User Guide - Page 103
    locating connectors on the SATA or SCSI backplane, see "Hot-Swap SATA Backplane Connections" or "Hot-Swap SCSI Backplane Connections." TP01350 Figure 71. Disconnecting the Power Cable from the Backplane Intel® Server Chassis SR2400/SR2400DC User Guide 79
  • Intel SR2400SYSD2 | User Guide - Page 104
    10. (Fixed SATA system only): Disconnect the SATA power adapter cable from the power supply. In the figure below, letter "B" is the connector from the power supply. Letter "A" is the connector from the SATA power adapter cable. B A AF00444 Figure 72. Disconnecting the Flex and Power Cables 11.
  • Intel SR2400SYSD2 | User Guide - Page 105
    "C" in the figure. B A C A AF00442 Figure 73. Removing the Power Distribution Module 13. Set the replacement power supply distribution module into the chassis and slide it backward against the power supply. See letter "A" in the figure below. Intel® Server Chassis SR2400/SR2400DC User Guide 81
  • Intel SR2400SYSD2 | User Guide - Page 106
    . (Hot-swap system only): Connect the flex cable to the server. Refer back to Figure 63 and see your server board documentation to locate the connection points for this cable. 20. Install the hot-swap power supply/supplies. For instructions, see "Installing a Hot-swap Power Supply." 21. Install the
  • Intel SR2400SYSD2 | User Guide - Page 107
    version of the Intel® Server Chassis SR2400. If you are installing or replacing a hot swap power supply for the Intel® Server Chassis SR2400DC, see "Installing or Replacing a Hot-swap Power Supply (DC Version)" for instructions. Removing a Hot-swap Power Supply To replace the power supply, use the
  • Intel SR2400SYSD2 | User Guide - Page 108
    swap power supply for the AC version of the Intel® Server Chassis SR2400, see "Installing or Replacing a Hot-swap Power Supply (AC Version)" for instructions. Removing a Hot-swap Power Supply To replace the power supply, use the following instructions. 1. (Non-redundant power supply only) Power down
  • Intel SR2400SYSD2 | User Guide - Page 109
    instructions. In the steps below, for assistance in locating connection points on the SATA backplane, see "HotSwap SATA Backplane Connections." For assistance in locating connection points on the SCSI backplane, see "Hot-Swap SCSI Backplane Connections." Intel® Server Chassis SR2400/SR2400DC
  • Intel SR2400SYSD2 | User Guide - Page 110
    and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the large air baffle. For
  • Intel SR2400SYSD2 | User Guide - Page 111
    is installed in the carrier. If the drives will be reinstalled, it is not necessary to remove the hard drives from the carriers. 8. Remove the fan module. For instructions, see "Removing the Fan Module." Intel® Server Chassis SR2400/SR2400DC User Guide 87
  • Intel SR2400SYSD2 | User Guide - Page 112
    avoid pinching any cables. Slide the backplane into the chassis guides at the left and right sides of the chassis until server board and the backplane. See letter "A" in the figure below. See your server board documentation to locate the connection point on the server board. 14. Connect the 2x3 power
  • Intel SR2400SYSD2 | User Guide - Page 113
    Drive" and "Installing or Removing a CD-ROM or DVD-ROM Drive." 22. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 23. (Optional): Install the front bezel. For instructions, see "Installing the Front Bezel." Intel® Server Chassis SR2400/SR2400DC User Guide 89
  • Intel SR2400SYSD2 | User Guide - Page 114
    Tape Drive To install a tape drive into your Server Chassis SR2400/SR2400DC, your system must meet the following requirements: ⎯ You must ." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see
  • Intel SR2400SYSD2 | User Guide - Page 115
    the combined tape drive bay / sixth drive bay until the carrier clicks into place. TP01357 Figure 82. Inserting the Tape Drive Carrier into the Chassis Intel® Server Chassis SR2400/SR2400DC User Guide 91
  • Intel SR2400SYSD2 | User Guide - Page 116
    cable along the front of the fan module and then through the front server board or add-in card. 12. Connect the 7-pin tape drive power cable to the backplane connector that is labeled "OPT CONN". 13. Connect the 4-pin tape power cable to the tape drive. 14. Install the chassis cover. For instructions
  • Intel SR2400SYSD2 | User Guide - Page 117
    bay. To access the drive bays, install the front bezel if it is installed. For instructions, see "Removing the Front Bezel." With the bezel removed, install the appropriate panel(s), blank A B C Figure 84. Installing the Filler Panels TP01169 Intel® Server Chassis SR2400/SR2400DC User Guide 93
  • Intel SR2400SYSD2 | User Guide - Page 118
    94
  • Intel SR2400SYSD2 | User Guide - Page 119
    are rated for no more than 25 Watts for any one slot. The average current usage per slot should not exceed 13 Watts. 600-W Redundant Power Supply Input Voltage (DC Version only) 600-W Power Supply -48VDC/-60VDC; 20.5 ADC maximum input current. Intel® Server Chassis SR2400/SR2400DC User Guide 95
  • Intel SR2400SYSD2 | User Guide - Page 120
    cause the power supplies to overheat and malfunction. The expansion slots on the server board are rated for no more than 25 Watts for any one slot. The average current usage per slot should not exceed 13 Watts. System Environmental Specifications Table 3. Environmental Specifications Temperature
  • Intel SR2400SYSD2 | User Guide - Page 121
    some of this information when you run the SSU. Item Chassis Manufacturer Name and Model Number Serial Number Date Installed Server Board Processor Speed and Cache Memory Video Display Keyboard Mouse Floppy Drive CD-ROM Drive Tape Drive Hard Disk Drive Hard Disk Drive Hard Disk Drive Hard
  • Intel SR2400SYSD2 | User Guide - Page 122
    Equipment Log (continued) Item Manufacturer Name and Model Number Serial Number Intel® Management Module Local Control Panel Date Installed 98
  • Intel SR2400SYSD2 | User Guide - Page 123
    configuration must be less than the wattage rating for your power supply. Use the two worksheets in this section to calculate Calculating DC Power Usage Table 4. Power Usage Worksheet 1 Current (maximum) at voltage level: Device Baseboard, Front Panel Board and Fans Processor(s) Memory 3.5-inch
  • Intel SR2400SYSD2 | User Guide - Page 124
    (5 V standby) X (______ A) ________ W Total Combined Wattage ________ W CAUTION Do not exceed a combined power output of 150 Watts for the +5 V and +3.3 V outputs. Exceeding a combined 150 Watts will overload the power subsystem and may cause the power supplies to overheat and malfunction. 100
  • Intel SR2400SYSD2 | User Guide - Page 125
    A Compliance The Server Chassis SR2400/SR2400DC has been has been tested and verified to comply with the following electromagnetic compatibility (EMC) regulations when installed a compatible Intel® host system. For information on compatible host system(s) refer to Intel's Server Builder Web site
  • Intel SR2400SYSD2 | User Guide - Page 126
    Certifications / Registrations / Declarations UL Certification (US/Canada) CE Declaration of Conformity (CENELEC Europe) FCC/ICES-003 Class A Attestation (USA/Canada) VCCI Certification (Japan) C-Tick Declaration of Conformity (Australia) MED Declaration of Conformity (New Zealand) BSMI
  • Intel SR2400SYSD2 | User Guide - Page 127
    accept any interference received, including interference that may cause undesired operation. For questions related to the EMC performance of this product, contact: Intel Corporation 5200 N.E. Elam Young Parkway Hillsboro, OR 97124 1-800-628-8686 Intel® Server Chassis SR2400/SR2400DC User Guide 103
  • Intel SR2400SYSD2 | User Guide - Page 128
    . This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation
  • Intel SR2400SYSD2 | User Guide - Page 129
    to the instruction manual. BSMI ( Intel representative 3. Name of Certification Recipient: Intel Corporation 4. Date of Manufacturer: Refer to date code on product 5. Manufacturer/Nation: Intel Corporation/Refer to country of origin marked on product Intel® Server Chassis SR2400/SR2400DC User Guide
  • Intel SR2400SYSD2 | User Guide - Page 130
    .com/go/serverbuilder If you do not have access to Intel's Web address, please contact your local Intel representative. Server Chassis (base chassis is provided with power supply and fans)⎯UL listed. Server board⎯you must use an Intel server board-UL recognized. Add-in boards⎯must have a printed
  • Intel SR2400SYSD2 | User Guide - Page 131
    support.intel.com/support/motherboards/server/chassis/SR2400 Telephone All calls are billed US $25.00 per incident, levied in local currency at the applicable credit card exchange rate plus applicable taxes. (Intel 2 68303634 (manual toll-free. Intel® Server Chassis SR2400/SR2400DC User Guide 107
  • Intel SR2400SYSD2 | User Guide - Page 132
    1288. Once connected, dial 800 843 4481 Paraguay 001 916 377 0114 Peru 001 916 377 0114 Uruguay 001 916 377 0114 For an updated support contact list, see http://www.intel.com/support/9089.htm/ 108
  • Intel SR2400SYSD2 | User Guide - Page 133
    a detailed problem description. Board / Chassis Information Baseboard Revision - PBA#: Baseboard Serial Number: CPU1 Speed/Stepping/Spec: CPU2 Speed/Stepping/Spec: System BIOS Version: HSC Firmware Version: Chassis Model Serial Number: Intel Server Chassis SR2400 Intel Server Chassis SR2400DC
  • Intel SR2400SYSD2 | User Guide - Page 134
    Operating System Information Operating System Version Service Pack # Peripheral Information Check each box On-Board Video Add-in Video NIC On-Board NIC1 (1.0 Gb) On-Board NIC2 (1.0 Gb) Driver Revision IRQ # I/O Base Address FW Rev# Hard Drive Information: ATA # of drives installed: Make
  • Intel SR2400SYSD2 | User Guide - Page 135
    Complete Problem Description In the space below, provide a complete description of the steps used to reproduce the problem or a complete description of where the problem can be found. Please also include any details on troubleshooting already done. Intel® Server Chassis SR2400/SR2400DC User Guide
  • Intel SR2400SYSD2 | User Guide - Page 136
    112
  • Intel SR2400SYSD2 | User Guide - Page 137
    Warranty does not cover damages due to external causes, including accident, problems with electrical power, usage not in accordance with product instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. Intel® Server Chassis SR2400/SR2400DC User Guide 113
  • Intel SR2400SYSD2 | User Guide - Page 138
    you. Limitations of Liability Intel's responsibility under this, or system containing this product. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This limited warranty gives you specific
  • Intel SR2400SYSD2 | User Guide - Page 139
    for the product, please go to the following Web site to obtain instructions: http://support.intel.com/support/motherboards/draform.htm In Europe and in Asia⎯Contact your original authorized distributor for warranty service. Any replacement Product is warranted under this written warranty and is
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Intel® Server Chassis SR2400/SR2400DC
User Guide
Order Number:
C51501-003