Invacare FRC3 Assembly Instructions

Invacare FRC3 Manual

Get Invacare FRC3 PDF manuals and user guides View all Invacare FRC3 manuals
Add to My Manuals
Save this manual to your list of manuals

Invacare FRC3 manual content summary:

  • Invacare FRC3 | Assembly Instructions - Page 1
    Assembly Instructions Invacare® Top End® Force™-3 Handcycle 1181408 REV A Be sure to record your serial number and read the owners manual.
  • Invacare FRC3 | Assembly Instructions - Page 2
    » 2 - footrest assemblies » 1 - drafting bumper » 1 - flag » 1 - box of hardware including 2 rear wheel axles, 2 split half clamps, 4 bolts, 4 washers, 4 locknuts, 2 footrest straps, 2 axle caps and the assembly instructions 1181408 REV A
  • Invacare FRC3 | Assembly Instructions - Page 3
    What you will need:  ¼" Allen wrench  4mm and 5mm Allen wrenches  10mm and 15mm open end wrenches  Recommended: Someone to assist  Assembly time is approximately 1-1 ½ hours 1181408 REV A
  • Invacare FRC3 | Assembly Instructions - Page 4
    Step 1: Set up  Remove all contents from box and use the box as a mat for assembling.  Double check the box to be sure all parts are removed.  Take the cardboard off of the frame and leave the plastic on the frame to avoid scratches. 1181408 REV A
  • Invacare FRC3 | Assembly Instructions - Page 5
    Step 2: Attach the Rear Wheels  Insert one axle into each of the two rear wheels. The bearings in the wheel hub will be facing in. This is the flat side.  Insert the wheels (which are marked left and right on a little tab on the wheel) on the proper side.  Use a ¼" Allen wrench to securely
  • Invacare FRC3 | Assembly Instructions - Page 6
    Step 3: Securing the Backrest  Loosen the pivot clamp and then insert backrest support tube into the pivot clamp that is welded to the camber bar.  Use a 5mm Allen wrench to tighten securely.  Note: It will be easier to
  • Invacare FRC3 | Assembly Instructions - Page 7
    Step 4: Installing Drafting Bumper  Loosen the drafting bumper receiver clamps using a 5mm Allen wrench.  Insert drafting bumper into receiver clamps.  Use 5mm Allen wrench to tighten the receiver clamps. 1181408 REV A
  • Invacare FRC3 | Assembly Instructions - Page 8
    Step 5: Installing the Cushions • Bend seat cushion in half to fit under seat straps. • Fit to desired position; this can be moved in the future. • Remove the loop fastener strip from the back cushion (it has a yellow film covering the adhesive side) • Remove the film from the adhesive side. •
  • Invacare FRC3 | Assembly Instructions - Page 9
    Step 6: Attaching the Fork 1, 2 and 3 To prepare for attaching the fork: 1. Use a 4mm Allen wrench to remove the headtube caps. 2. Remove the cardboard spacers and discard. 3. Reattach the headtube caps, leaving them loose. 4. Release the parking brake. 5. Remove bolt from rubber dampener using
  • Invacare FRC3 | Assembly Instructions - Page 10
    Step 6: Attaching the Fork (continued) 1. Line up the split half clamps on the fork to rest on each side of the silver spindle (headtube) on the bike frame. 2. Put the screw that was removed from the dampener through the elongated hole (on the tab welded to the headtube) into the dampener. 3. Take
  • Invacare FRC3 | Assembly Instructions - Page 11
    Notes  To make sure there is no play in the fork, you will want to position yourself on the riders left of the bike, grab the front of the frame and the bottom left of the fork and pull down. There should be no movement. If there is movement, go back and tighten the caps until there is no movement.
  • Invacare FRC3 | Assembly Instructions - Page 12
    Step 7: Installing the Footrests  Engage parking brake.  Remove the box from under the handcycle.  Loosen both bolts on the footrest clamp on each side using 4mm Allen wrench.  Insert the footrest into the clamps.  Tighten securely using 4mm Allen wrench and 10mm wrench. 1181408 REV A
  • Invacare FRC3 | Assembly Instructions - Page 13
    Step 8: Attaching the Footrest Straps  Take the two straps and unfasten the two longer bottom hook and loop straps.  Wrap the straps around the footrests so they are securely fastened to the hook and loop fastener located on the footrest post. 1181408 REV A
  • Invacare FRC3 | Assembly Instructions - Page 14
    Step 9: Installing the Safety Flag  Insert the two posts of the flag together and then insert into the flag holder on the back of the bike. 1181408 REV A
  • Invacare FRC3 | Assembly Instructions - Page 15
    Before Riding Your New Handcycle  Before you take the bike out, you will want to make sure everything is tight, including the fork clamp.  Release your parking brake and watch the lower derailleur to make sure your chain is not slipping while you run through all your gears(by cranking the
  • Invacare FRC3 | Assembly Instructions - Page 16
    Before Riding Your New Handcycle (CONT.)  Engage your hand brake, and make sure the disc brake caliper engages.  Check your parking brake again, and make sure not only that it engages but also that the pads are lined up on the metal part of the wheel rim.  Pump up your tires to 100 PSI. 1181408
  • Invacare FRC3 | Assembly Instructions - Page 17
    to our Force Series Owner's manual online (topendwheelchair.com) for instructions on proper fitting, operation and safety of your new Invacare Top End Force-3 handcycle.  If you have any questions, please call Invacare Top End customer service
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
Assembly Instructions
Invacare® Top End® Force™
-3 Handcycle
1181408 REV A
Be sure to record your serial number and read the owners manual.