Invacare MVPJRF60 Owners Manual

Invacare MVPJRF60 Manual

Get Invacare MVPJRF60 PDF manuals and user guides View all Invacare MVPJRF60 manuals
Add to My Manuals
Save this manual to your list of manuals

Invacare MVPJRF60 manual content summary:

  • Invacare MVPJRF60 | Owners Manual - Page 1
    Owner's Operator And Maintenance Manual MVP™ MVP jr.™ DEALER: THIS MANUAL MUST BE GIVEN TO THE USER OF THE WHEELCHAIR. USER: BEFORE USING THIS WHEELCHAIR, READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE.
  • Invacare MVPJRF60 | Owners Manual - Page 2
    WHEELCHAIR MUST BE PERFORMED BY A QUALIFIED TECHNICIAN. PROCEDURES OTHER THAN THOSE DESCRIBED IN THIS MANUAL MUST BE PERFORMED BY A QUALIFIED TECHNICIAN. THE FOLLOWING PROCEDURES ARE FOUND IN THE SERVICE MANUAL -TIPPER MOUNTING BRACKETS SAVE THESE INSTRUCTIONS MVP™ & MVP jr.™ 2 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 3
    WEIGHT LIMITATION ...11 SAFETY/HANDLING OF WHEELCHAIRS 12 SECTION 2 - SAFETY INSPECTION 18 SAFETY INSPECTION CHECKLIST 18 TROUBLESHOOTING ...19 MAINTENANCE ...19 SECTION 3 - 36 INSTALLING AND REMOVING A SEATING SYSTEM 37 FOLDING/UNFOLDING THE WHEELCHAIR 38 Part No. 1106638 3 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 4
    GUARDS 49 CANTILEVER ARM PAD DEPTH ADJUSTMENT/REPLACEMENT 51 SECTION 7 - WHEELS 52 REPAIRING/REPLACING PNEUMATIC TIRE/TUBE 52 REMOVING/INSTALLING REAR WHEELS 52 ADJUSTING QUICK-RELEASE AXLES 56 INSTALLING/ADJUSTING THE ANTI-TIPPERS 57 LIMITED WARRANTY 60 MVP™ & MVP jr.™ 4 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 5
    manual apply to hazards or unsafe practices which could result in personal injury or property damage. NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. WHEELCHAIR USER As a manufacturer of wheelchairs, Invacare A WHEELCHAIR. Part No. 1106638 5 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 6
    diameter of the axle bushing for a positive lock. Keep detent balls clean. WARNING DO NOT OPERATE WITHOUT THE ANTI-TIP TUBES REV. 5/98 INSTALLED. P/N 60106X144 MVP jr. ONLY MVP ONLY MVP Heavy Duty ONLY MVP™ & MVP jr.™ 6 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 7
    Sizes 16-inch 18-inch 20-inch 22-inch 24-inch, Carbon/Turbo/Spinergy 25-inch, Spinergy 26-inch, Primo/Continental 26-inch, Spinergy 700C FRONT Caster Sizes 3-inch 5-inch 6-inch 8-inch Back Height: Back Angle Range Conventional Crossbraces: Less Seat Rail Crossbraces: Arm Styles: MVP & MVP jr. OPEN
  • Invacare MVPJRF60 | Owners Manual - Page 8
    : Caster Size: Seat Cushion: Back Upholstery: Shipping Weight (approx.): MVP & MVP jr. SWINGAWAY inch (Urethane or Pneumatic), Precision Sealed Bearings Flat Free Inserts 2 or 3-inch (Optional) Black Nylon (Standard), Adjustable Back Upholstery (Optional) 26 lbs. - 52 lbs. MVP™ & MVP jr.™ 8 Part
  • Invacare MVPJRF60 | Owners Manual - Page 9
    Seat Dump Back Angle Seating System Caster Size Caster Position Rear Wheel Size Rear Wheel wheelchair to decrease in stability. ALWAYS ensure stability BEFORE moving the rear wheels forward. TEST wheelchair BEFORE it is occupied by the end user to ensure safety. Part No. 1106638 9 MVP™ & MVP jr
  • Invacare MVPJRF60 | Owners Manual - Page 10
    Invacare. DO NOT attempt to lift or tilt a wheelchair by using any removable (detachable) parts. Lifting by means of any removable (detachable) parts of a wheelchair may result in injury to the user or damage to the wheelchair. DO NOT stand on the frame of the wheelchair. MVP™ & MVP jr.™ 10 Part
  • Invacare MVPJRF60 | Owners Manual - Page 11
    WARNING The Invacare MVP jr. wheelchair has a weight limitation of 150 lbs. (68 kg.). The Invacare MVP wheelchair has a weight limitation of 250 lbs. (113.4 kg.). The Invacare MVP Heavy Duty wheelchair has weight is limited to 230 lbs. (250 lbs. - 20 lbs.). Part No. 1106638 11 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 12
    only as a “basic” guide. The techniques that are discussed on the following pages have been used successfully by many. Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual. Invacare recognizes and encourages each
  • Invacare MVPJRF60 | Owners Manual - Page 13
    wheelchair. Also, be aware of any removable (detachable) parts. These must NEVER be used to move the wheelchair or as lifting supports, Wheelchair CENTER OF GRAVITY SHORTENING Front of Wheelchair Part No. 1106638 LENGTHENING NOTE: Curved rear frame shown. UNOCCUPIED 13 OCCUPIED MVP™ & MVP jr
  • Invacare MVPJRF60 | Owners Manual - Page 14
    gravity and may cause you to tip over. Position wheelchair as close as possible to the desired object. Point front casters forward to create the longest possible wheelbase. Reach back only as far as your arm will extend without changing your sitting position. MVP™ & MVP jr.™ 14 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 15
    backward far enough for the front casters to clear the edge of the curb. METHOD 2 - WHEELCHAIR WITHOUT STEP TUBE Roll the wheelchair backward and SLOWLY lower the front casters onto the sidewalk. Turn the anti-tippers so the anti-tip wheels are facing down. Part No. 1106638 15 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 16
    or down the stairs. Invacare recommends that, if possible, the occupant be removed from the wheelchair prior to moving. The manufacturer recommends using two (2) assistants and making thorough preparations. Make sure to use ONLY secure, non-detachable parts for hand-held supports. DO NOT attempt to
  • Invacare MVPJRF60 | Owners Manual - Page 17
    casters parallel to it. Remove, lower or rotate the armrest so it is out of the way. Engage wheel locks. Shift body weight into seat with transfer. During independent transfer, little or no seat platform will be beneath you. Use a transfer board if at all possible. Part No. 1106638 17 MVP™ & MVP
  • Invacare MVPJRF60 | Owners Manual - Page 18
    - Safety Inspection includes the following: Safety Inspection Checklist Troubleshooting Maintenance NOTE: Twice a year take your wheelchair to a qualified technician for a thorough inspection and servicing. Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your
  • Invacare MVPJRF60 | Owners Manual - Page 19
    your Invacare MVP, make sure all nuts and bolts are tight. Check all parts for damage or wear and replace. Check all parts for proper adjustment. WARNING DO NOT use WD-40®, 3-in-1 oil®, or other penetrating lubricants on quickrelease axles. Otherwise, binding and/or damage to the wheelchair may
  • Invacare MVPJRF60 | Owners Manual - Page 20
    wear. Refer to REPLACING/ ADJUSTING WHEEL LOCKS in SECTION 8 of this manual. 9. Periodically check caster wheel bearings to make sure they are clean and free from moisture. Use a Teflon lubricant if necessary. 10. Check upholstery for sagging, rips or tears. MVP™ & MVP jr.™ 20 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 21
    WARNING After ANY adjustments, repair or service and BEFORE use, make the wheelchair until it locks into place. ADJUSTING NOTE: The footplate will be on the inside of the wheelchair Part No. 1106638 FIGURE 1 - INSTALLING/REMOVING/ ADJUSTING THE FOOTREST(S) SWINGAWAY FRONT FRAME 21 MVP™ & MVP jr
  • Invacare MVPJRF60 | Owners Manual - Page 22
    two (2) socket screws that secure the flip-up footrest to the wheelchair frame. 2. Move the flip-up footrest to one (1) of three (3) positions. 3. Reinstall the two (2) socket screws that secure the flip-up footrest to the wheelchair frame and securely tighten. MVP™ & MVP jr.™ 22 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 23
    Remove any accessories that are attached to the footrests. 2. Remove the socket bolt, coved washer and locknut that secure the footplate to the footrest support. 3. Reposition the inside of the wheelchair and swing the legrest to the outside of the wheelchair. Part No. 1106638 23 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 24
    B. LOWERING - Support leg with one wheelchair. 2. Slide the calfpad up or down until the desired position is obtained. 3. To secure the calfpad, turn the calfpad towards the inside of the wheelchair. Calfpad MVP™ & MVP jr.™ Adjust Calfpad Secure Calfpad FIGURE 6 - ADJUSTING CALFPADS 24 Part
  • Invacare MVPJRF60 | Owners Manual - Page 25
    footrest is secured to the wheelchair before using. 5. Refer to ENTERING/EXITING THE WHEELCHAIR in this section of the manual when ready to exit the wheelchair. Flip-up Footrest Engagement Knob Slot Extension Tube Latch FIGURE 7 - USING THE FLIP-UP FOOTREST Part No. 1106638 25 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 26
    of the front casters. 1. Loosen, wheelchair. Refer to INSTALLING/REMOV- ING/ADJUSTING THE FOOTREST(S) in this section of the manual. Footrest Tube Footplate Footrest Tube Flat Screws Washers and Locknuts (under the footplate) FIGURE 8 - ADJUSTING THE FLIP-UP FOOTREST MVP™ & MVP jr.™ 26 Part
  • Invacare MVPJRF60 | Owners Manual - Page 27
    and down motion of the footplate hinge to make sure the user of the wheelchair can operate the footplates easily. NOTE: If the footplate's motion is too Support Tube Footplate Hinge Socket Screw FIGURE 9 - INSTALLING ADJUSTABLE ANGLE FLIP-UP FOOTPLATE HINGE Part No. 1106638 27 MVP™ & MVP jr
  • Invacare MVPJRF60 | Owners Manual - Page 28
    of the front casters. Otherwise, injury Support Flat Screws DETAIL "A" - SIDE VIEW OF FOOTPLATE AND FOOTREST SUPPORT Footrest Support Footplate Footplate Half Clamp Footplate Hinge Adjustment Screw Locknuts FIGURE 10 - ADJUSTING ADJUSTABLE ANGLE FLIP-UP FOOTPLATES MVP™ & MVP jr.™ 28 Part
  • Invacare MVPJRF60 | Owners Manual - Page 29
    screw and locknut until the spacer is secure. COMPOSITE/ALUMINUM/ TUBULAR FOOTPLATES Hex Screw/Coved Washer Phillips Screw Spacer Locknut FIGURE 11 - HEEL LOOP REPLACEMENT Part No. 1106638 29 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 30
    Pull the footboard towards the front of the wheelchair. INSTALLING 1. Make sure the latches on the is locked in place BEFORE using the wheelchair. 3. Push DOWN to lock the latches hex screws that secure the footboard clamp to the footrest support. 2. Repeat STEP 1 for the opposite footboard clamp.
  • Invacare MVPJRF60 | Owners Manual - Page 31
    support tube securely. Flat Screws Footboard Latches Flat Screws Hex Screws Footboard Clamp Button Screws Footboard Support NOTE: Exploded for Clarity, DO NOT disassemble. FIGURE 13 - REMOVING/INSTALLING/ADJUSTING THE ADJUSTABLE ANGLE ONE PIECE FOOTBOARD Part No. 1106638 31 MVP™ & MVP jr
  • Invacare MVPJRF60 | Owners Manual - Page 32
    (rear) of the wheelchair depending on need. UNFOLDING Actuator FRONT OF WHEELCHAIR 1. To lock the back into place, pull UP until there is an audible click. FIGURE 1 - FOLDING/ UNFOLDING THE BACK 2. Push on the back to make sure it is locked in place. MVP™ & MVP jr.™ 32 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 33
    screws and locknuts that secure the back canes to the wheelchair frame. Back Upholstery Back Cane Back Cane Back Height Adjustment Screw NOTE: Fixed (non-folding) back cane shown. HOLE 1 2 3 4 5 FIGURE 2 - ADJUSTING THE BACK HEIGHT Wheelchair Frame Part No. 1106638 33 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 34
    Mounting Hole Back Angle Adjustment Screw DETAIL "A" - BACK ANGLE MOUNTING HOLES UPPER 0° 5° 10° 15° LOWER 15° 10° 5° 0° FIGURE 3 - ADJUSTING THE BACK ANGLE - SQUARE REAR FRAME MVP™ & MVP jr.™ 34 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 35
    THE CHEST POSITIONING STRAP NOTE: Ensure strap is oriented properly and not twisted when installing. 6. Repeat STEPS 4-5 for opposite side of NEW chest positioning strap. Part No. 1106638 35 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 36
    . E. Push down on stroller handle to ensure release levers hold the desired position of the stroller handle. F. Repeat STEPS A-E until release levers hold the position. MVP™ & MVP jr.™ 36 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 37
    A SEATING SYSTEM WARNING DO NOT use parts, accessories, or adapters other than those authorized by Invacare. 1. Ensure that the seating system is compatible with this wheelchair. 2. Refer to the seating system Owner's Manual for installation and removal. Part No. 1106638 37 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 38
    repair or service and BEFORE use, make sure all E attachment hardware is tightened securely - otherwise, injury or damage may result. FOLDING/UNFOLDING THE WHEELCHAIR ends of the crossbraces with the palms of your hands. FOLDING Conventional Crossbraces. 1. Lift up on the seat upholstery until
  • Invacare MVPJRF60 | Owners Manual - Page 39
    1 - FOLDING/UNFOLDING THE WHEELCHAIR REPLACING SEAT UPHOLSTERY (FIGURE 2) 1. Remove the seat cushion, if necessary, from the wheelchair. 2. The number of phillips screws will vary depending on the depth of the wheelchair. 3. Remove the existing seat upholstery. 4. Install the new seat upholstery
  • Invacare MVPJRF60 | Owners Manual - Page 40
    the seat positioning strap, proceed to STEP 5. B. Remove the EXISTING seat positioning strap from the wheelchair. 5. Secure the two (2) halves of the NEW seat positioning strap together. 6. Position one way. FIGURE 3 - INSTALLING/REMOVING SEAT POSITIONING STRAP MVP™ & MVP jr.™ 40 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 41
    clamps on inside and outside of the wheelchair frame. NOTE: Make sure the threaded half clamp is on the outside of the wheelchair frame. Wheelchair Frame Half Clamp Socket Screw 2. CLOTHING GUARDS 5. Repeat STEPS 1-4 for the opposite rigid side guard. Part No. 1106638 41 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 42
    /Replacement WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attachment hardware is tightened securely - otherwise, injury or damage may result. DO NOT attempt to lift or tilt a wheelchair by using any removable (detachable) parts. Lifting by means of any removable
  • Invacare MVPJRF60 | Owners Manual - Page 43
    wheelchair frame as shown in FIGURE 1. 2. Position the top coved washer between the arm socket and the wheelchair through the wheelchair frame, wheelchair frame. 5. Install the bottom hex screw through the wheelchair to the wheelchair frame. 7. Wheelchair Wheelchair Frame TOP Hex Screw Part No
  • Invacare MVPJRF60 | Owners Manual - Page 44
    on the wheelchair with the top hex screw in the top mounting hole of the arm socket and the bottom hex screw in the slot of the arm socket. Half Arm Arm Socket Locknut Washers Three (3) Mounting Positions Hex Screw FIGURE 2 - ADJUSTING HALF ARM HEIGHT MVP™ & MVP jr.™ 44 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 45
    on the side rail to the UP (HORIZONTAL) position. 2. Remove armrest from the wheelchair. REPLACING ARMRESTS NOTE: Armrest release levers MUST be in the unlocked position when placing REPLACING DUAL POINT ARM PAD / REPLACING DUAL POINT ARM CLOTHING GUARDS Part No. 1106638 45 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 46
    socket. Refer to ADJUSTING THE T-ARMS in this section of the manual. 2. Repeat STEP 2 for opposite side of the wheelchair. T-Arm Wheelchair Frame T-Arm Socket Locking Lever (Towards the front of the wheelchair.) Slot FIGURE 5 - INSTALLING/REMOVING T- ARMS MVP™ & MVP jr.™ 46 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 47
    release lever towards the inside of the wheelchair. NOTE: If necessary, pull out so it can be flipped towards the outside of the wheelchair. 2. Slide the T-arm to one (1) of: lever towards the front of the wheelchair. Set Screws Inside T-Arm Post Part No. 1106638 Arm Pad Arm Tube Phillips
  • Invacare MVPJRF60 | Owners Manual - Page 48
    SOCKETS (FIGURE 9) 1. Remove the rear wheels from the wheelchair, if necessary. Refer to REMOVING/INSTALLING REAR WHEELS in SECTION 7 of this manual. 2. Loosen, but do not remove the four (4) Refer to REMOVING/INSTALLING REAR WHEELS in SECTION 7 of this manual. MVP™ & MVP jr.™ 48 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 49
    to 80-90 in./lbs. 5. Install the T-arm onto the wheelchair. Refer to INSTALLING/REMOVING T-ARMS in this section of the manual. Side Guard T-Arm Transfer Assist Socket Screws Bottom Clamp FIGURE 10 - ADJUSTING T-ARM TRANSFER ASSISTS AND/OR SIDE GUARDS Part No. 1106638 49 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 50
    Pull the actuator of the locking mechanism towards the front of the wheelchair. 2. While holding the actuator of the locking mechanism, pull to ADJUSTING CANTILEVER ARM ANGLE in this section of the manual. Adjusting Cantilever Arm Height (FIGURE 11). NOTE: When MVP™ & MVP jr.™ 50 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 51
    Cantilever Slide Tube NOTE: This Phillips Screw only needs to be removed when Armrest Pad is replaced. FIGURE 12 - CANTILEVER ARM PAD DEPTH ADJUSTMENT/ REPLACEMENT Part No. 1106638 51 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 52
    Adjusting Forks WARNING After ANY adjustments, repair or service and BEFORE use, make sure all manual. NOTE: During contact activities, Invacare recommends inserting quick-release axles with the head end to the inside of the wheelchair to prevent accidental release. MVP™ & MVP jr.™ 52 Part
  • Invacare MVPJRF60 | Owners Manual - Page 53
    pins clean. 5. Reinstall rear wheel onto the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. Axle Mounting Plate Locknut Locking Pins Detent Pin Quick- Release Axle Wheel Hub FIGURE 2 - ADJUSTING QUICK-RELEASE AXLES Part No. 1106638 53 MVP™ & MVP jr.™
  • Invacare MVPJRF60 | Owners Manual - Page 54
    IN AND/OR OUT (FIGURE 4) 1. Remove rear wheel and the quadrelease axle from the wheelchair. 2. Loosen the locking screw. Quad-Release Handle Locking Pins Axle Mounting Plate 3. Make . 5. Reinstall the rear wheel and quad-release axle onto the wheelchair. MVP™ & MVP jr.™ 54 Part No. 1106638
  • Invacare MVPJRF60 | Owners Manual - Page 55
    wheelchair for maneuverability. Caster Headtube TOP VIEW Locknut 4. Readjust locknuts if necessary, and repeat STEPS 1-3 until correct. 5. Snap dust cover into the caster headtube. FIGURE 6 - ADJUSTING FORKS 6. Repeat STEPS 1-5 for opposite side, if necessary. Part No. 1106638 55 MVP™ & MVP
  • Invacare MVPJRF60 | Owners Manual - Page 56
    repair or service from the wheelchair. 2. Install the inch (1/8-inch) Under Mount Wheel Lock 3/16-inch (1/8-inch) High Mount / Under Mount Thumb Saver Wheel Lock Thumb Saver Wheel Lock Tire Wheel Lock Shoe Shoe Tire FIGURE 1 - REPLACING/ADJUSTING THE WHEEL LOCKS MVP™ & MVP jr.™ 56 Part
  • Invacare MVPJRF60 | Owners Manual - Page 57
    FRAME - REAR mounting hole (DETAIL "B"). NOTE: A 1-1/2 to 2-inch clearance between the bottom of the anti-tipper wheels and the ground/ floor wheelchair. 3. Adjust the anti-tipper height. Refer to ADJUSTING THE ANTI-TIPPER HEIGHT in this section of the manual. Part No. 1106638 57 MVP™ & MVP jr
  • Invacare MVPJRF60 | Owners Manual - Page 58
    wheelchair frame. 2. Slide the half clamps forward or rearward along the wheelchair frame until the 1-1/2 to 2-inch clearance is achieved. 3. Securely tighten the three (3) hex screws that secure the half clamps and anti-tipper mounting brackets to the wheelchair frame. MVP™ & MVP jr.™ 58 Part
  • Invacare MVPJRF60 | Owners Manual - Page 59
    Wheelchair Frame Release Button Anti-tipper Mounting Bracket 1-1/2 to 2-inch Clearance Half Clamps Locknuts Anti-tipper Mounting Bracket Hex Screws Release Buttons Anti-tipper Anti-tipper Mounting Bracket FIGURE 2 - INSTALLING/ADJUSTING THE ANTI-TIPPERS Part No. 1106638 59 MVP™ & MVP jr
  • Invacare MVPJRF60 | Owners Manual - Page 60
    any labor or shipping charges incurred in replacement part installation or repair of any such product. Invacare’s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and/or replacement. For warranty service, please contact the dealer from whom you purchased
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Owner's Operator And Maintenance Manual
MVP
±
MVP jr²
±
DEALER: THIS MANUAL MUST BE GIVEN TO
THE USER OF THE WHEELCHAIR±
USER: BEFORE USING THIS WHEELCHAIR,
READ THIS MANUAL AND SAVE FOR FUTURE
REFERENCE±