Invacare TDXSIV-2 Owners Manual 4

Invacare TDXSIV-2 Manual

Get Invacare TDXSIV-2 PDF manuals and user guides View all Invacare TDXSIV-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Invacare TDXSIV-2 manual content summary:

  • Invacare TDXSIV-2 | Owners Manual 4 - Page 1
    Invacare® Van Seat Power Wheelchair Seat User Manual EN This manual MUST be given to the user of the product. BEFORE using this product, read this manual and save for future reference.
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 2
    . All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by ™ and ®. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 3
    ...9 Operation Information ...10 Setup ...10 Transport...10 Repair or Service Information ...11 Safety/Handling ...11 Pinch Points ...12 Stability and Interference (EMI) From Radio Wave Sources...15 Powered Wheelchair Electromagnetic Interference (EMI) ...16 Invacare® Van Seat 3 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 4
    Powered Seating Systems...21 Using the Powered Manual Center Mount Footrest...29 Removing ...29 Installing...29 6 ADJUSTMENT 30 Footrest Height Adjustment ...30 PHWH93 ...31 PH904A and PHAL4A...31 Adjusting the Height of the Manual Center Mount Footrest ...32 Part No 1143195 4 Invacare
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 5
    CONTENTS Adjusting the Angle of the Manual Center Mount Footrest...33 Adjusting the Footplate Angle...34 Service Inspection ...39 Six Month Inspection ...40 Troubleshooting ...40 Replacing Heel Loops...41 Adjusting/Replacing Telescoping Front Rigging Supports ...42 Invacare® Van Seat 5 Part
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 6
    GENERAL 1 General 1.1 Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal if it is not avoided.  Gives useful tips, recommendations and information for efficient, trouble-free use. Invacare® Van Seat 6 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 7
    to wheelchair base owner's manual for additional safety and operation information. Refer to the table below for part numbers of additional documents which are referenced in this manual. MK6i™ Electronics Programming Guide MANUAL 1 GENERAL PART NUMBER 1141471 Part No 1143195 7 Invacare® Van
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 8
    'S CONTROL, AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS. A CHANGE IN OPERATING NOISE, PARTICULARLY RELATIVE TO MOTORS AND GEARBOXES DOES NOT CONSTITUTE A FAILURE
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 9
    IS SUBJECT TO CHANGE WITHOUT NOTICE. Check all parts for shipping damage and test before using. In case of damage, DO NOT use. Contact Invacare/Carrier for further instruction. As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of wheelchairs to meet many needs of the end
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 10
    2.2 Operation Information Setup ƽ WARNING A qualified technician must perform the initial set up of this wheelchair. Also, a qualified technician must perform all procedures in the service manual. Performance adjustments should only be made by professionals of the healthcare field or persons fully
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 11
    Except for programming, DO NOT service or adjust the wheelchair while occupied, unless otherwise noted. Before adjusting, repairing or servicing the wheelchair, ALWAYS turn the wheelchair power Off, otherwise, injury or damage may occur. Wheelchairs should be examined during maintenance for
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 12
    active use of the wheelchair. DO NOT attempt to wheelchair to tip over. DO NOT wheelchair and/or seating system (if any) may tip over. ALWAYS keep hands and fingers clear of moving parts using the wheelchair. If loose, contact a qualified technician for instructions. Pinch Points
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 13
    wheelchair. Other general wheelchair. Footplates and Front Rigging ƽ WARNING DO NOT use the footplates as a platform. DO NOT stand on the footplates/footboard. When getting in or out of the wheelchair of the wheelchair. When casters. Otherwise damage to the wheelchair may result or may impede proper
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 14
    shower. DO NOT leave power wheelchair in a damp area for any length of time. Direct exposure to rain or dampness will cause the wheelchair to malfunction electrically and mechanically; may cause the wheelchair to prematurely rust or may damage the upholstery. Invacare® Van Seat 14 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 15
    or damage may result. 2.4 Electromagnetic Interference (EMI) From Radio Wave Sources Powered wheelchairs and motorized scooters (in this text, both will be referred to as powered wheelchairs) may be susceptible to electromagnetic interference (EMI), which is interfering electromagnetic energy
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 16
    EMI problems to your powered wheelchair. Powered Wheelchair powered wheelchairs and motorized scooters. FOLLOWING THE WARNINGS LISTED BELOW SHOULD REDUCE THE CHANCE OF UNINTENDED BRAKE RELEASE OR POWERED WHEELCHAIR MOVEMENT WHICH COULD RESULT IN SERIOUS INJURY. Invacare® Van Seat 16 Part
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 17
    or turn ON personal communication devices, such as cellular phones, while the powered wheelchair is turned ON; 2) Be aware of nearby transmitters, such as radio of this scooter as manufactured by Invacare may adversely affect the EMI immunity levels. Part No 1143195 17 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 18
    3 LABEL LOCATIONS 3 Label Locations  Refer to the owner's manual shipped with wheelchair base for additional labels located on the wheelchair base. Invacare® Van Seat Weight Capacity Label located here 18 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 19
    ° to 170° Adjustable Angle Depth and Width Grey Vinyl, Grey Cloth, Tan Vinyl Flip Up, Depth and Height Adjustable, Footboard, Swingaway Front Rigging, Elevating Legrest 9° Part No 1143195 19 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 20
    the wheelchair. DO NOT attempt to adjust the drive lock-out. Have the wheelchair serviced by a qualified technician. The wheelchair user MUST the wheelchair user's line of sight while driving. Make sure the wheelchair user can see properly to ensure safe driving. Invacare® Van Seat 20 Part
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 21
    19 for recline angle ranges. 5.2 Operating Powered Seating Systems ƽ GENERAL WARNINGS Refer to the wheelchair. DO NOT attempt to adjust the drive lock-out. Have the wheelchair serviced by Invacare shall not be liable and the limited warranty is void. Part No 1143195 21 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 22
    sure the wheelchair is on a level surface. 2. Press the powered seating switch once to activate the actuator. 3. Press the powered seating switch sure the wheelchair is on a level surface. 2. Press the mode button to switch from driving mode to tilt mode. Invacare® Van Seat 22 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 23
    Button (Hare) Service Indicator  *The mode button is only present on SPJ+ w/ACC joystick. FIGURE 1 Using the MK6i SPJ+ w/ACC Joystick 5 USAGE Joystick Additional Input for Powered Seating Switch Charger/ Programming Input Active (If Programed) Part No 1143195 23 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 24
    page 25. 1. Make sure the wheelchair is on a level surface. 2. powered seating operation has been programmed for this quadrant.  The three icons indicate up/down, up or down, respectively. 5. Select the desired operation using the joystick or an equivalent switch. Invacare® Van Seat 24 Part
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 25
    5 USAGE  While operating the powered seating system, the selected icon will display on the screen along Switch Remote On/ Off Input To Controller DETAIL "B" - EXAMPLE SCREEN DURING POWERED SEATING OPERATION Icon Text FIGURE 2 Using the CMPJ+ Joystick Part No 1143195 25 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 26
    The remote reset switch may be used to stop the wheelchair if the wheelchair is in motion. The remote reset switch also functions in rear of the joystick on the right side and allows the power switch to be operated by an ability switch (normally open momentary Invacare® Van Seat 26 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 27
    * • Information Center Display Selection (does not require Reset activation at power up) If any of the above modes are selected, the control wheelchair, make sure that the footplates are in the upward position or swing footrests towards the outside of the wheelchair. Part No 1143195 27 Invacare
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 28
    lever inward and rotate the footrest out. 2. Lift up on front rigging and remove from the wheelchair. 3. Repeat STEPS 1-2 for opposite side of wheelchair. Front Rigging Release Lever Front Rigging Hinge Plate FIGURE 3 Installing/Removing Front Riggings Invacare® Van Seat 28 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 29
    the release lever and raise front rigging to the desired height. • Lowering - Support front rigging with one hand away from the release lever. Push release lever downward Center Mount Footrest Part No 1143195 FIGURE 5 Removing/Installing the Manual Center Mount Footrest 29 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 30
    WARNING While the wheelchair is moving, minimum ground clearance for the front rigging is three inches. If the wheelchair is not moving, the front rigging MUST maintain a minimum of one inch ground clearance - otherwise personal injury and damage may result. Invacare® Van Seat 30 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 31
    . 4. Repeat STEPS 1-3 for the opposite side of the wheelchair footrest, if necessary.  PH904A style front rigging shown. PHAL4A front rigging adjusts the same way. Part No 1143195 31 6 ADJUSTMENT Footrest Support Locknut Coved Washer Coved Washer Hex Bolt Lower Footrest FIGURE 1 Footrest
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 32
    . The user's feet MUST remain on the center mount footrest while operating the wheelchair. If the user's feet are allowed to rest off the side of the Tube Mounting Holes Extension Tube Invacare® Van Seat FIGURE 3 Adjusting the Height of the Manual Center Mount Footrest 32 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 33
    and casters. The user's feet MUST remain on the center mount footrest while operating the wheelchair. If the user's feet are allowed to rest off the side of the center mount Footplate FIGURE 4 Adjusting the Angle of the Manual Center Mount Footrest Part No 1143195 33 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 34
    . 2. Tighten the front rigging angle hinge mounting screw to increase the rotation effort. 3. Repeat STEPS 1 and 2 for the other footplate. Manual Center Mount Footrest Footplate (shown away from Extension Tube) Adjustment Screw FIGURE 5 Adjusting the Footplate Angle Center Mount Front Rigging
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 35
    the seat frame assembly and tighten securely. Armrest DETAIL "A" - ANGLE Adjustment Screw DETAIL "B" - HEIGHT Height Adjustment Holes Seat Frame Assembly Lock Knob Jam Nut Armrest Part No 1143195 FIGURE 7 Adjusting Armrests 35 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 36
    in position when an audible "click" is heard. 2. To lower headrest, push release tab towards the inside of the wheelchair. Lower headrest to desired position. Invacare® Van Seat 36 Release Handle FIGURE 8 Adjusting the Back Angle Headrest Release Tab Headrest Tube FIGURE 9 Adjusting Armrests
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 37
    and as necessary, take your wheelchair to a qualified technician for a thorough inspection and servicing. Refer to Service Inspection on page 39. Refer to wheelchair base owner's manual for additional safety inspection and troubleshooting information.  Check all parts for shipping damage. In case
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 38
    service inspections. Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair. To operate properly and safely, your wheelchair of your wheelchair. Refer to wheelchair base owner's manual for additional safety inspection and troubleshooting information.
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 39
    Every six months take your wheelchair to a qualified technician for a thorough inspection and servicing. Service inspections MUST be performed by a qualified technician. Refer to wheelchair base owner's manual for additional safety inspection and troubleshooting information. ƽ WARNING After ANY
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 40
    -out operates properly.  Check limit switch position. 7.4 Troubleshooting  For troubleshooting information and explanation of error codes, refer to the wheelchair base owner's manual and the individual Electronics Manual supplied with each wheelchair. Invacare® Van Seat 40 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 41
    heel loop to lower footrest, tighten the phillips screw and locknut until the spacer is secure. 7 SETUP/MAINTENANCE Locknut Coved Washer Footrest Support Hex Bolt Phillips Bolt Spacer Lower Footrest Heel Loop Locknut FIGURE 1 Replacing Heel Loops Part No 1143195 41 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 42
    inside of the wheelchair when locked in place. 3. Using the two socket bolts and locknuts, secure the telescoping front rigging support to the seat frame as shown in FIGURE 2. 4. If necessary, repeat STEPS 1-3 on remaining telescoping front rigging support. Invacare® Van Seat 42 Part No 1143195
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 43
    7 SETUP/MAINTENANCE Mounting Bolts Seat Frame Telescoping Front Rigging Support Spacer Locknuts 87 65 4 32 Not Used Mounting Holes 5 and 6 Holes 4 and 5 Holes 4 and 5 Holes 6 and 7 FIGURE 2 Adjusting/Replacing Telescoping Front Rigging Supports Part No 1143195 43 Invacare® Van Seat
  • Invacare TDXSIV-2 | Owners Manual 4 - Page 44
    Part No 1143195 Rev F - 05/11 Invacare Corporation USA One Invacare Way Elyria, Ohio USA 44036-2125 800-333-6900 www.invacare.com Canada 570 Matheson Blvd E Unit 8 Mississauga Ontario L4Z 4G4 Canada 800-668-5324
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
User Manual
This manual MUST be given to the user of the product.
BEFORE using this product, read this manual and save for future reference.
EN
Invacare®
Van Seat
Power Wheelchair Seat