JVC DTV20L1U Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages)
JVC DTV20L1U - Multi Format LCD Monitor Manual
UPC - 046838028496
View all JVC DTV20L1U manuals
Add to My Manuals
Save this manual to your list of manuals |
JVC DTV20L1U manual content summary:
- JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 1
DT-V24L1D DT-V24L1 DT-V20L1D DT-V20L1 MULTI FORMAT LCD MONITOR The illustration of the monitor is of DT-V24L1D. INSTRUCTIONS Table of Contents Safety Precautions 2 IMPORTANT SAFEGUARDS 2 Maintenance 3 Installation 4 Using the monitor on the stand 4 Installing the monitor in the rack 5 Daily - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 2
use, and service. Please read these "IMPORTANT SAFEGUARDS" carefully before use. • All the safety and operating instructions by JVC could uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual or short-circuit the parts, which could result - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 3
replacement parts are required, be sure the service technician has used replacement parts specified JVC Technology Centre Europe GmbH Postfach 10 05 52 61145 Friedberg Germany Information for Users on Disposal of Old Equipment [European Union] This symbol indicates that the electrical and electronic - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 4
you cannot tilt the monitor downward. The illustrations of the monitor are of DT-V24L1D. CAUTION • When lifting up the stand, lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel being damaged. • Be careful not to pinch your fingers in the moving parts. • Make sure to - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 5
higher position Screw holes for lower position 7 Installing the monitor in the rack (DT-V20L1D and DT-V20L1 only) Use a JVC's RACK MOUNT ADAPTER (RK-C20L1; not supplied). CAUTION The illustration of the monitor is of DT-V24L1D. Screw holes (See page 18 for the specifications of the screw holes.) - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 6
7 Front panel DT-V24L1 and DT-V20L1 do not input or signal format (the lamp lights even when the function does not actually work). The illustration of the monitor is of DT-V24L1D :9. • To return to 4:3, press the button again. • Use this function when the picture of 16:9 aspect ratio is squeezed - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 7
Operation guide When the set-up menu is displayed Selected item Operation guide 2 DT-V24L1D and DT-V20L1D only) Select audio channels of EMBEDDED AUDIO signals to output from the speakers (L/R) and MONITOR • Not displayed when no EMBEDDED AUDIO signal is input or "LEVEL METER ch" is set to "OFF" (☞ - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 8
is output from this terminal only when the monitor is on. q DVI-D (HDCP) terminal Input terminal for the DVI-D signal. • Select the signal type in "DVI INPUT SEL." corresponding to the type of the input signal (☞ page 10). *Using the audio level meter (DT-V24L1D and DT-V20L1D only) You can check the - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 9
/60i 16 1035/60i 17 1080/50i 18 1080/60p 19 1080/50p 20 1080/30p 21 1080/25p 22 1080/24p 23 1080/30psF 24 1080/24psF VIDEO (INPUT1, INPUT2) Input terminal COMPO./RGB (Analog component/ analog RGB) HD/SD SDI (IN 1, IN 2)*1 (DT-V24L1D and DT-V20L1D only - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 10
input or the input signal. These items are not available. Technical information Setting of "MARKER SELECT" and "R-MARKER SELECT" The setting values and features to LCD. OFF use for DVI-D (HDCP) terminal. NOTE • DVI-D input of the monitor DT-V24L1D and DT-V24L1 only *2 Memorized for each input. - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 11
the sync signal for the VIDEO and COMPO./RGB input. QUICK SWITCHING Select the quickness for switching the input. Setting value OFF, SUSPEND (suspend mode), GRAY B.(gray screen) 5sec., 20sec., 1min., 15min., 30min. INT., EXT. STD., QUICK *1 DT-V24L1D and DT-V20L1D only *2 Memorized for each - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 12
guide Shows the buttons for each operation. NOTE • The menu automatically disappears in about 30 seconds after the last menu operation. • Some items may not appear on the menu depending on the input or the input 8sec. NOTE The tally lamp is controlled using MAKE/TRIG. terminal of REMOTE terminals (☞ - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 13
HOUR METER" and the settings done by using the adjustment knobs on the front panel will not be reset. • After performing "all reset," the monitor is turned off then turned on automatically. *1 DT-V24L1D and DT-V20L1D only *2 Memorized for each input. 4 Repeat steps 2 and 3 (10 characters at maximum - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 14
(☞ the right). (2) TRIGGER (trigger system) : Controls the function by inputting the pulse signal instantaneously to the corresponding pin terminal (☞ the right). • RS-232C terminal : Controls the monitor with RS-232C system. (☞ "Using the serial communication" on page 15) • RS-485 terminals - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 15
, 01: On 00: 4:3, 01: 16:9 *1 These commands can be used while the monitor is off (standby). *2 These commands are available for only DT-V24L1D and DT-V20L1D. *3 Displays the information shown when INPUT SELECT button of the current input is pressed (☞ "About the Status Display" on page 7). While - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 16
or brightness by using the The picture of the LCD display and troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the problem. The illustration of the monitor is of DT-V24L1D - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 17
DT-V24L1D/DT-V24L1 DT-V20L1D/DT-V20L1 Type Multi format LCD monitor Screen size Type 24 wide format Type 20 wide format Aspect ratio 16:10 LCD panel 24 A (AC 120 V)/0.60 A (AC 220 - 240 V) External dimensions (excluding protruding parts) Width : 564 mm (22 1/4˝) 564 mm (22 1/4˝) Height - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 18
Specifications (cont.) 7 Dimensions Unit: mm (inch) DT-V24L1D/DT-V24L1 564 (22 1/4) 99 (4) ) 99 (4) 52.7 (2 1/8) 1.5 (1/16) The illustrations of the monitor are of DT-V24L1D. 100 VESA mounting holes (Size: M4, depth: 10 mm) 100 - JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 19
- JVC DTV20L1U | Operator manual for DT-V24L1/D, DT-V20L1/D (20 pages) - Page 20
DT-V24L1D/DT-V24L1/DT-V20L1D/DT-V20L1 MULTI FORMAT LCD MONITOR © 2006 Victor Company of Japan, Limited 1106MKH-MW-VP
INSTRUCTIONS
DT-V24L1D
DT-V24L1
DT-V20L1D
DT-V20L1
MULTI FORMAT LCD MONITOR
Table of Contents
Safety Precautions
..............................................
2
IMPORTANT SAFEGUARDS
...........................
2
Maintenance
.....................................................
3
Installation
............................................................
4
Using the monitor on the stand
........................
4
Installing the monitor in the rack
.......................
5
Daily Operations / Connections
.........................
6
Front panel
.......................................................
6
Rear panel
........................................................
8
Available signals
...............................................
9
Menu Configuration—MAIN MENU
..................
10
Menu Configuration—SET-UP MENU
...............
12
External Control
.................................................
14
About the external control
..............................
14
Using the MAKE/TRIGGER system
.................
14
Using the serial communication
.....................
15
Troubleshooting
.................................................
16
Self-check program
........................................
16
Specifications
....................................................
17
General
...........................................................
17
Input/output terminals
.....................................
17
Dimensions
.....................................................
18
The illustration of the monitor is of DT-V24L1D.
LCT2202-001A