JVC GM-F520S Instruction Manual
JVC GM-F520S - 1920 X 1080 Full Hd Lcd Monitor Manual
 |
UPC - 046838037573
View all JVC GM-F520S manuals
Add to My Manuals
Save this manual to your list of manuals |
JVC GM-F520S manual content summary:
- JVC GM-F520S | Instruction Manual - Page 1
GM-F520S GM-F470S GM-F420S LCD DISPLAY MONITOR The illustration of the monitor is of GM-F470S. INSTRUCTIONS • Be sure to read through "Safety Precautions" ( 22 Using the LAN system 23 Troubleshooting 25 Self-diagnostic indication 27 Specifications 28 General 28 Input/output terminals 29 Dimensions - JVC GM-F520S | Instruction Manual - Page 2
and maintenance (servicing) instructions in the may touch dangerous voltage points or short-circuit the parts, which could result in a fire.) • Do not apply any strong shock to the LCD panel. (Do not hit any object against it or When using stands for this monitor, use the supplied stands and attach them - JVC GM-F520S | Instruction Manual - Page 3
not installed and used in accordance with the instructions, may cause harmful interference to radio communications . - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. of Victor Company of Japan, Limited is: JVC Technical Services Europe GmbH - JVC GM-F520S | Instruction Manual - Page 4
the monitor, or may cause the monitor to topple over. Fan B Fan A (only on GM- monitor vertically • Make sure to install the monitor in the direction illustrated below. • Set the speed of the internal cooling fan to "HIGH" (see "COOLING MODE" on page 16). • You can change the position of the JVC - JVC GM-F520S | Instruction Manual - Page 5
remote control.) t Muting button (see page 10) ‡: Main power off Turns off the volume immediately. The illustration of the monitor used for explanation in this manual is of GM-F470S. Inserting the batteries Use two AA/R6 dry cell batteries. Insert the batteries from the · end, making sure the - JVC GM-F520S | Instruction Manual - Page 6
NOT connect the power cord until all connections are completed. • Refer also to the user manual of each piece of equipment. • Do not short-circuit 9 and ( speaker cords to each other. (Refer also to the instructions supplied with the speakers.) To bind the cables (example): 6 Insert the end of the - JVC GM-F520S | Instruction Manual - Page 7
D-sub 15-pin cable RGB output C VIDEO VIDEO IN Audio input terminals Input terminals on the monitor D AUDIO 1 AUDIO 1 IN E AUDIO 2 AUDIO 2 IN BNC cable Video output Since Use the speakers with the following specification: Impedance: Between 6 Ω and 8 Ω Power handling capacity: More than 7 - JVC GM-F520S | Instruction Manual - Page 8
The following signals can be input to this monitor. Video signals Signal name NTSC 3.58 PAL-M coming through the analog RGB terminal may not be displayed properly due to their synchronization signal. Specifications of the DVI-D (HDCP) terminal Pin No. Signal name 1 T.M.D.S Data 2- 2 T.M.D.S - JVC GM-F520S | Instruction Manual - Page 9
although it's frequency is within the acceptable range. • Depending on the connected equipment, the monitor may not be compatible with G on sync signals. • When a preset mode signal is 31.469 37.879 48.363 56.476 60.023 68.667 44.820 47.760 47.712 48.363 67.500 63.981 63.981 65.220 75.000 56. - JVC GM-F520S | Instruction Manual - Page 10
| : Main power on ‡: Main power off On the top of the rear panel On the bottom of the rear panel Turning on the monitor • To turn off the monitor, press POWER OFF. On the main unit: Each time you press the button, the power turns on and off. Selecting an input On - JVC GM-F520S | Instruction Manual - Page 11
input is displayed. Current input Input signal format DVI 1400 x 1050A 60Hz NOTE • When no signal is input, "NO SYNC" appears. When a signal this monitor does not support is input, "Out of range" appears. • When "STATUS DISPLAY" on the set-up menu is set to "AUTO" (see page 15), the status is - JVC GM-F520S | Instruction Manual - Page 12
30 seconds after the last operation. From the remote control On the monitor Works in the same way as SET-UP on the remote control. SELECT : 5 ∞ ADJUST : 2 3 EXIT : MENU Setting values Sub menu Operation guide Shows the buttons for each operation. 3 Select an item in the sub menu by pressing - JVC GM-F520S | Instruction Manual - Page 13
Menu Configuration-MAIN MENU PICTURE SETTING Item PICTURE MODE CONTRAST BRIGHT CHROMA PHASE SHARPNESS BACK LIGHT COLOR TEMP. To do Setting value Select a picture mode (see "Selecting the picture mode" DYNAMIC, NORMAL, USER on page 11). Adjust contrast of the picture. -20 += 00 += +20 Adjust - JVC GM-F520S | Instruction Manual - Page 14
the color system. When you cannot view pictures correctly with "AUTO," select an appropriate option according to the current input. Set the multiple monitor usage-Multi Display. • See also "Example of the Multi Display setting" below. Turn on/off the Multi Display. Select the number and layout - JVC GM-F520S | Instruction Manual - Page 15
Item ID REMOTE IN SEL. CNT. RJ45 OUT CNT. RJ45 IN PORT F1 - PORT F5 reset To do Setting value Assign the ID to the monitor. 01 += 25 Select the input terminal used for external control. D-sub9 (RS-232C input), RJ-45 (RS-485 input/ output), LAN (Ethernet terminal) Select the - JVC GM-F520S | Instruction Manual - Page 16
POWER ON DELAY Sets the time till the power supply to the monitor's circuits starts after the power button (POWER ON button on the remote control • Fan B is always in operation while the power is on. Fan A (only on GM-F520S) Fan A Fan B reset Restores the default setting for all the items in the - JVC GM-F520S | Instruction Manual - Page 17
right. ENTER PASS ID 3 Enter the password. The Security Lock is set to "ON." • If the Power-on Timer (see the right) is activated, the monitor turns on at the specified power-on time without the password. To deactivate the Security Lock 1 Select "SECURITY LOCK (: ON)" on the SECURITY LOCK sub - JVC GM-F520S | Instruction Manual - Page 18
from falling. GM-F470S/GM-F420S GM-F520S Example: When the setting (4) above is activated... Displaying A on the main window and B on the sub Detection range of the sensor about 5 m about 100° about 80° A and B switches after detection. Not available when the monitor is installed using - JVC GM-F520S | Instruction Manual - Page 19
control by the MAKE system can control that function. You cannot use other external control and the buttons on the remote control and the monitor. • The status of the monitor returns automatically to that before detecting human as the time set on "SUSTAIN TIME" passed without another detection. The - JVC GM-F520S | Instruction Manual - Page 20
) (see page 21). (2) IR OUT system: Controls other equipment through the monitor by using the remote control supplied with the equipment. (3) MAKE (make contact system): Controls the function by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it - JVC GM-F520S | Instruction Manual - Page 21
the external control equipment. For details, see on the right. • Commands starting with "@" are status returns from the monitor. This is a female terminal. Pin IN terminal OUT terminal No. signal signal 1 TXD + TXD + 2 TXD - JVC GM-F520S | Instruction Manual - Page 22
function you want to assign. • For functions which can be assigned, see the table below. Operation 1. Short-circuit the 6th pin terminal (External control) to the 8th pin terminal (GND) so that the monitor can be controlled by the external control. 2. Set "CNT. RJ45 IN" of "REMOTE SYSTEM" to "MAKE - JVC GM-F520S | Instruction Manual - Page 23
of the browser before starting the operation. 1. Start Internet Explorer (6.0 or 7.0) on the computer. 2. Enter the IP address of the monitor to the address bar, then press Enter on the keyboard. The log-in screen appears. GM-F420/470/520 Series Web Control Enter Log In Name : OK 1 Turns on/off the - JVC GM-F520S | Instruction Manual - Page 24
ON 3 INPUT: VIDEO SIGNAL FORMAT: NTSC ASPECT: REGULAR COLOR TEMP: MID COMMAND to Send 2 ---> Send COMMAND STATUS SENDING... 1 To turn on the monitor when the motion sensor detects the motion of human, select "ON." 2 To change the volume level when the motion sensor detects the motion of - JVC GM-F520S | Instruction Manual - Page 25
Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solves the problem, unplug the monitor and consult an authorized dealer or service . • "POP before SMTP" is not supported. Self-diagnostic lamp lights (flashes). ] See - JVC GM-F520S | Instruction Manual - Page 26
a problem. The LCD display is built with very high precision technology; however, be aware that a few pixels may be missing or constantly lit. • The following symptoms are problems only when pictures or sounds are not played back normally. - A slight electric shock occurs when you touch the monitor - JVC GM-F520S | Instruction Manual - Page 27
Report Sheet Store name where you purchased the monitor To Model name: LCD DISPLAY MONITOR GM-F520S/GM-F470S/GM-F420S The self-diagnostic lamps light or flash as listed on the following table. Please give me immediate advice or service if necessary. Self-diagnostic lamp No. Lamp position - JVC GM-F520S | Instruction Manual - Page 28
Specifications General Model name GM-F520S GM-F470S GM-F420S Type LCD Monitor Screen size Type 52 wide format Type 47 wide format Type 42 wide format Aspect ratio 16:9 (Wide format) LCD panel 52 inch wide, active matrix TFT 47 inch wide, active matrix TFT 42 inch wide, active matrix - JVC GM-F520S | Instruction Manual - Page 29
A 695.2 (27 3/8) 661.2 (26 1/8) 648.0 (25 1/4)*2 Dimensions GM-F520S Top view Front view Rear view Dimensions Motion sensor Unit: mm (inch) *2 Effective screen size *1 1 152.0 (45 5/16)*2 1 165.2 (45 7/8) 1 199.2 (47 1/4) 400 (15 3/4) Side view *1 161.5 (6 3/8) 400 (15 3/4) 200 (7 7/8) 56 (2 - JVC GM-F520S | Instruction Manual - Page 30
Specifications (cont.) Dimensions GM-F470S Top view *1 Front view Side view *1 620.4 (24 1/2) 590.4 (23 1/4) 584.8 (23)*2 Rear view 1 040 (40 15/16)*2 1 045.2 (41 1/4) 1 075.2 (42 3/8) 400 (15 3/4) 151.2 (6) Unit: mm (inch) *1 Screw holes for optional usage *2 Effective screen size GM-F420S - JVC GM-F520S | Instruction Manual - Page 31
- JVC GM-F520S | Instruction Manual - Page 32
GM-F520S/GM-F470S/GM-F420S LCD DISPLAY MONITOR © 2009 Victor Company of Japan, Limited 0209TKH-MW-MT
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
INSTRUCTIONS
GM-F520S
GM-F470S
GM-F420S
LCD DISPLAY MONITOR
LCT2505-002A-H
Table of Contents
Safety Precautions
..............................................
2
IMPORTANT SAFEGUARDS
...........................
2
Maintenance
.....................................................
3
Installation
............................................................
4
Parts Identification
..............................................
5
Connections
.........................................................
6
Available signals
...............................................
8
Daily Operations
................................................
10
Menu Operation
.................................................
12
Menu Configuration—MAIN MENU
..................
13
Menu Configuration—SET-UP MENU
...............
15
Using the Motion Sensor
..................................
18
Outline of the motion sensor
..........................
18
Installation and connection
.............................
18
Setting
............................................................
19
How to Use External Control
............................
20
About the external control
..............................
20
Using the serial communication
.....................
21
Using the MAKE/TRIG. system
......................
22
Using the LAN system
....................................
23
Troubleshooting
.................................................
25
Self-diagnostic indication
................................
27
Specifications
....................................................
28
General
...........................................................
28
Input/output terminals
.....................................
29
Dimensions
.....................................................
29
The illustration of the monitor is of GM-F470S.
• Be sure to read through “Safety Precautions” (pages 2 and 3)
before using the unit.