JVC GY-DV700WUCL Instruction Manual

JVC GY-DV700WUCL - Cineline Dv Camcorder Manual

Get JVC GY-DV700WUCL - Cineline Dv Camcorder PDF manuals and user guides View all JVC GY-DV700WUCL manuals
Add to My Manuals
Save this manual to your list of manuals

JVC GY-DV700WUCL manual content summary:

  • JVC GY-DV700WUCL | Instruction Manual - Page 1
    JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance. For Customer Use : Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. GY-DV700W Serial No. This instruction manual
  • JVC GY-DV700WUCL | Instruction Manual - Page 2
    service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the appliance. c. If the appliance has been exposed to rain or water. d. If the appliance does not operate normally by following the operating instructions
  • JVC GY-DV700WUCL | Instruction Manual - Page 3
    to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. INFORMATION FOR radio/TV technician for help. CAUTION CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER'S AUTHORITY TO OPERATE THE EQUIPMENT. THIS DEVICE COMPLIES
  • JVC GY-DV700WUCL | Instruction Manual - Page 4
    Camcorder GY-DV700W. These instructions are for GY-DV700WU. This may infringe on the rights of copyright holders. ● JVC cannot assume liabilities that may derive from the impossibility . MAIN FEATURES ● 16:9 and 4:3 aspect ratio Supports both NORMAL screen and WIDE screen format. Simply switch
  • JVC GY-DV700WUCL | Instruction Manual - Page 5
    CONTENTS INTRODUCTION MAIN FEATURES 4 1. INTRODUCTION 1-1 Main Unit Configuration 6 1-2 Precautions for Proper Use 7 1-3 Routine and Periodical Maintenance 7 1-4 Precautions for Use of Head Cleaning Tape 8 1-5 Videocassette to be Used 8 1-6 Battery Pack to be Used 9 1-7 Condensation 9 1-8
  • JVC GY-DV700WUCL | Instruction Manual - Page 6
    Iris 80 • Zebra Pattern Display during Manual Adjustment ...... 80 13-3 Shooting the GY-DV700W) Microphone CR230V32 Lithium battery Head cleaning tape OTHERS 14. OTHERS 14-1 Troubleshooting 86 • Alarm Indications 86 • Warnings in Viewfinder 88 • Troubles with Error Code Outputs 90 • Troubles
  • JVC GY-DV700WUCL | Instruction Manual - Page 7
    spots may be generated. When storing the GY-DV700W for a long time, the storage of professional video equipment at your nearest JVC-authorized service agent. The setup level is never attached troubles that may be caused by the sudden occurrence of failure. As the replacement, adjustment and servicing
  • JVC GY-DV700WUCL | Instruction Manual - Page 8
    head cleaning tapes other than specified. For instructions on how to use the head cleaning dirt adheres to the heads of the GY-DV700W, the following indications appear during nearest JVC-authorized service agent. Use the following chart as a guide for periodical head cleaning. Operating
  • JVC GY-DV700WUCL | Instruction Manual - Page 9
    be Used ● Use JVC's videocassette tapes marked reduce the rotary head life. 1-6 Battery Pack to be Used The GY-DV700W can use any of the following battery packs. ● Flat shape (dewing). When this occurs, the head drum and tape guides are covered with droplets allowing the tape to be stuck to
  • JVC GY-DV700WUCL | Instruction Manual - Page 10
    patterns are only displayed on the viewfinder screen. The zebra patterns are not generated for the MONITOR OUT or Y/C OUT output.  See "Zebra Pattern during Manual Adjustment" on page 80. • The default value is 70% - 80%. The luminance level can be changed with the ZEBRA setting in the VF DISPLAY
  • JVC GY-DV700WUCL | Instruction Manual - Page 11
    /Lens lock lever Hold the lens and use the lever to turn the ring anticlockwise to release lens. To mount lens make sure the lens guide pin fits well, and then turn the ring clockwise until firm.  See "Attaching the Zoom Lens" on page 31. ! [FILTER] Color temperature conversion filter control
  • JVC GY-DV700WUCL | Instruction Manual - Page 12
    the white balance to their optimum levels. • The iris is placed in automatic mode even if the iris mode switch of the lens is in manual. • The gain will vary continuously to the maximum of +12 dB. The shutter speed will vary continuously to the minimum of 1/200 of a second.  See
  • JVC GY-DV700WUCL | Instruction Manual - Page 13
    balance. # [NG] button Pressing this button while recording or in the record-pause mode deletes the S.S.F. data stored in the memory of the GY-DV700W with the S.S.F. (Super Scene Finder) function. This function is only valid in the MARK mode.  See "S.S.F. (Super Scene Finder) Function" on page
  • JVC GY-DV700WUCL | Instruction Manual - Page 14
    reference level even when sounds greater than the reference level are input. The audio input level does not increase when the input level is low. MANUAL: The audio input level can be adjusted with the CH-2 AUDIO LEVEL control 3. 7 [CH-1 AUDIO INPUT] selector switch This switch is used to select the
  • JVC GY-DV700WUCL | Instruction Manual - Page 15
    CH-1 AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE MENU used for the backup of the time code and time date. The GY-DV700W delivered without the battery installed. The provided lithium battery is for
  • JVC GY-DV700WUCL | Instruction Manual - Page 16
    not illuminated. (Keep this switch at OFF during battery operation of the GY-DV700W or when it is required to reduce the power consumption for some switching lever on a designated lens or by using the ASPECT RATIO item in the GY-DV700W's camera OPERATION Menu.  See "Lens (Optional)" on page 23.
  • JVC GY-DV700WUCL | Instruction Manual - Page 17
    • Displays the VCR setup menu data when the GY-DV700W is in the VCR setup menu mode by pressing Counter Display Contents" on page 22.  See "TROUBLES WITH ERROR CODE OUTPUTS" on page 90. ^ Section using the provided head cleaning tape. For instructions on head cleaning tape, read "Precautions for
  • JVC GY-DV700WUCL | Instruction Manual - Page 18
    closing it. • If the cassette cover is not closed, the GY-DV700W will remain inoperative. Memo: To prevent penetration of foreign objects into 050 REMOTE SELECT must be set to "RS232C". For details, please consult your JVC dealer. Note: • When a cable is connected to the VTR REMOTE connector,
  • JVC GY-DV700WUCL | Instruction Manual - Page 19
    2-4 Top Section 2. CONTROLS, INDICATORS AND CONNECTORS q w PUSH OPEN w EJECT LOG REW STOP FF PLAY STILL i y ruet 1 [EJECT] switch Slide to the side when inserting or ejecting the videocassette. Sliding this switch opens the cassette cover. If the switch is moved while the power is off,
  • JVC GY-DV700WUCL | Instruction Manual - Page 20
    2. CONTROLS, INDICATORS AND CONNECTORS 2-5 Rear Section !1 PUSH !0 DV CAMCORDER GY-DV700 q w e EARPHONE DV CH-1 AUDIO IN CH-2 LINE MIC LINE MIC DC INPUT +48V ON +48V ON TALLY DC OUTPUT i o u Y/C OUT MONITOR OUT LINE OUT
  • JVC GY-DV700WUCL | Instruction Manual - Page 21
    switch 8 on page 14 to "REAR". 7 [TALLY] Back tally lamp This lamp lights up when the GY-DV700W enters the record mode. It blinks during the transition to the record mode. • Use the VCR Setup Menu person in charge of professional video equipment at your nearest JVC-authorized service agent. 21
  • JVC GY-DV700WUCL | Instruction Manual - Page 22
    4. Error code/Alarm display The error code or alarm indicator is displayed automatically in case an abnormal condition occurs with the unit.  See "TROUBLES WITH ERROR CODE OUTPUTS" on page 90.  See "ALARM INDICATIONS" on page 86. Remaining Battery Power Display The 7-dot segment bar display shows
  • JVC GY-DV700WUCL | Instruction Manual - Page 23
    the Auto Iris Function while it is held down only. 12 ZOOM mode knob S : Servo Zoom mode. Allows operation by the Zoom Servo Control lever 9 . M : Manual Zoom mode. Allows zoom control by the Zoom lever/ring 2 . 13 REMOTE FOCUS control connector To connect with an optional focus servo unit. 14 ZOOM
  • JVC GY-DV700WUCL | Instruction Manual - Page 24
    2. CONTROLS, INDICATORS AND CONNECTORS 2-8 1.5-Inch Viewfinder (optional) VF-P116W 1 2 3 4 5 76 0 9 8 1 Eyepiece Blocks light to viewfinder screen and holds eye optics. The Eyepiece can be opened to view the screen directly. 2 Eyepiece focusing ring Rotate this ring to adjust the viewing angle.
  • JVC GY-DV700WUCL | Instruction Manual - Page 25
    following circumstances. Steady green : During recording. Blinks green : • While the GY-DV700W switches from record-pause to recording. • Immediately before the tape is or when it has run out. • When an error occurs in the GY-DV700W. • When the battery voltage becomes too low. Ⅲ VIEWFINDER SCREEN
  • JVC GY-DV700WUCL | Instruction Manual - Page 26
    2. CONTROLS, INDICATORS AND CONNECTORS 2-9 Indications in Viewfinder (Cont'd) ACCU - FOCUS 1 2 G F 3 4 I SD 5 B 6 7 Status 0 ACCU - FOCUS 1 2 G F 3 4 7 I SD 5 B 6 F5 . 6 CH1 CH2 M 09 9 C STBY < 60 1 2 . 4V 9 B 08 A Status 1 SCENE F I LE WH I TE BA L F I L TER SHUT
  • JVC GY-DV700WUCL | Instruction Manual - Page 27
    2. CONTROLS, INDICATORS AND CONNECTORS 2-9 Indications in Viewfinder (Cont'd) ● Status 1 In addition to the information on the Status 0 screen, this screen displays audio indicators and information on remaining tape, voltage and lens F-number. Display position Display 8 (Example) CH1 CH2
  • JVC GY-DV700WUCL | Instruction Manual - Page 28
    2-9 Indications in Viewfinder (Cont'd) Ⅲ Alarm Message Display ACCU - FOCUS G Alarm message display F F5 . 6 STBY CH1 CH2 < 60 I B 1 2 . 4V The following alarm messages are displayed on the status 0 and status 1 screens. Indication LOW BATTERY CLOSE CASSETTE COVER VTR WARNING [HEAD] VTR
  • JVC GY-DV700WUCL | Instruction Manual - Page 29
    2-9 Indication in Viewfinder (Cont'd) Ⅲ Safety Zone Three types of safety zone items can be displayed in the viewfinder. Select the required one with the SAFETY ZONE item on the VF DISPLAY menu screen. The CENTER MARK item can be used to select whether the safety zone center mark indicator should be
  • JVC GY-DV700WUCL | Instruction Manual - Page 30
    -2 LEVEL LIGHT ON OFF COUNTER CTL TC UB TRIPOD BASE GY-DV700W STANDARD PACKAGE FOCUS MANUAL UNIT HZ-FM13 (FUJINON) HZ-FM15 (CANON) ZOOM SERVO For PC/AT) Y/C CABLE VCG30, VCG50 BNC CABLE When 4:3 lens is mounted on the GY-DV700W. 1 When used in the 4:3 mode, approximately 20% of the image angle is
  • JVC GY-DV700WUCL | Instruction Manual - Page 31
    this portion and pull straight out. 3-3 Attaching the Viewfinder (optional) Sliding securing ring 1. 5. 4. Mounting guide Stopper screw 1. Loosen the stopper screw. 2. Attach the viewfinder with its guide aligned with the shoe. 3. Connect the cable connector as shown in the figure on the
  • JVC GY-DV700WUCL | Instruction Manual - Page 32
    to the viewfinder. The provided microphone is a phantom microphone. 1. Loosen the stopper screw on the viewfinder. 2.Attach the microphone to the attachment guide on the viewfinder as illustrated. 3. Confirm that there is no gap between the microphone and the viewfinder, and then tighten the stopper
  • JVC GY-DV700WUCL | Instruction Manual - Page 33
    3. BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 3-6 Attaching the Tripod Base (provided) 1. Tripod mounting holes Front mount clip 2. Safety lever 4. Front base mount 2. Lock lever 3. Rear base mount Use the provided tripod base to place the camera on a tripod. 1. Attach the tripod base on the
  • JVC GY-DV700WUCL | Instruction Manual - Page 34
    ADJUSTMENTS 3-7 Inserting and Replacing Backup Lithium Batteries The GY-DV700W uses a lithium battery for backup of -2 LEVEL CH-1 AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE MENU FRONT REAR
  • JVC GY-DV700WUCL | Instruction Manual - Page 35
    If the cable is not equipped with a ferrite core, please contact your JVC dealer. Do not use any power source with large fluctuations in the power POWER switch of the GY-DV700W to ON. Power is supplied to the VCR section and the camera. * For details, read the instruction manual of the AA-P250
  • JVC GY-DV700WUCL | Instruction Manual - Page 36
    4. POWER SUPPLY 4-2 Battery Pack Operation (Cont'd) Attaching a Flat Shape Type Battery Pack 1. Open the battery case cover while pushing the lock release lever. 2. Insert the battery pack into the battery case with its electrodes facing the unit. 3. Close the battery case cover. Lock release
  • JVC GY-DV700WUCL | Instruction Manual - Page 37
    13/14 Series), it is necessary to detach the battery case from the GY-DV700W and replace it with the Anton-Bauer battery holder. Use the following UB Battery Attaching the Battery Pack 1. Align the 3 guide pins of the battery pack with the guide holes on the battery holder, and push straight to
  • JVC GY-DV700WUCL | Instruction Manual - Page 38
    beeps REC lamp After the remaining battery power warnings appear, the GY-DV700W automatically stops operation if the battery power operation is continued. in a car, etc.), this could cause leakage of the fluid or shorten service life. ● When the terminal section of the battery pack gets dirty, the
  • JVC GY-DV700WUCL | Instruction Manual - Page 39
    setting of the VTR switch as follows: VTR switch setting SAVE GY-DV700W operation mode GY-DV700W enters the SAVE mode (tape protect mode) and stops from the STBY mode. STBY When a recordable videocassette is loaded, the GY-DV700W enters the record-pause mode automatically. (The drum motor is
  • JVC GY-DV700WUCL | Instruction Manual - Page 40
    After the cassette cover is closed, it takes about 8 seconds before the unit can start recording or before it enters the stop mode. CAUTION: The GY-DV700W cannot be operated while the cassette cover is open. Make sure to close the cover before operating the unit. Unloading the Cassette 1. Set the
  • JVC GY-DV700WUCL | Instruction Manual - Page 41
    -2 LEVEL Ⅲ Check that the lithium battery has been inserted. 2. COUNTER switch CH-1 AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE MENU FRONT REAR GROUP HOLD ITEM SELECT DATA SET SHIFT ADVANCE
  • JVC GY-DV700WUCL | Instruction Manual - Page 42
    6. SETTING AND ADJUSTMENTS BEFORE SHOOTING 6-1 Camera Settings 3. FUJINON ASPHERIC & IF 19x TV . ZOOM 5 7 10 15 30 ∞ ft 1.5 2 3 5 10 m 8.7 20 C 16 11 8 5.6 M O FILTER 1 3200k 2 5600k+1/8ND 3 5600k 4 5600k+1/64ND SHUTTER STATUS A CR MENU ALARM MONITOR AUTO IRIS FULL AUTO BLACK
  • JVC GY-DV700WUCL | Instruction Manual - Page 43
    color bar signal on the video monitor and adjust the colors, contrast and brightness. 1. Connect a color video monitor to the MONITOR OUT connector of the GY-DV700W. 2. Set the OUTPUT switch to BARS to output the color bar signal (SMTPE type color bars). 3. Set the monitor's BLUE CHECK function to
  • JVC GY-DV700WUCL | Instruction Manual - Page 44
    more than 3 meters from the camera. The optimal subject for this adjustment is a Siemens star chart. 1. Set the IRIS mode switch to M (Manual). 2. Set the zoom mode to MANU (Manual). 3. Open the iris ring. If the illumination is too strong, reduce it or move to a darker place. 4. Turn the zoom lever
  • JVC GY-DV700WUCL | Instruction Manual - Page 45
    contains only a single color or not enough white color. • The accuracy of the FAW (Full-time Auto White balance) is inferior to that of the manual white balance. • When the power is turned on with the FAW mode selected, it takes about 10 seconds for the FAW adjustment to be completed
  • JVC GY-DV700WUCL | Instruction Manual - Page 46
    AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE channel. ● LONG PAUSE TIME Select the time (in minutes) until the GY-DV700W enters the tape protection mode (drum rotation stops) when the recordpause mode
  • JVC GY-DV700WUCL | Instruction Manual - Page 47
    LEVEL LIGHT ON OFF COUNTER CTL TC UB CH-1 AUDIO CH-2 LEVEL AUTO MANUAL AUDIO SELECT AUDIO INPUT CH-1 CH-2 FRONT REAR CH-1 AUDIO LINE/MIC AUDIO INPUT connector CH-1 AUDIO INPUT switch CH-2 AUDIO INPUT switch The GY-DV700W is provided with the microphone connector on the front section and
  • JVC GY-DV700WUCL | Instruction Manual - Page 48
    in the record, record-pause or stop mode. 1. Set the AUDIO SELECT switch of the channel whose audio input level that you want to adjust manually to MANUAL. 2. Rotate the audio input level control corresponding to the audio input to be adjusted. • Adjust so that the peak level does not exceed the
  • JVC GY-DV700WUCL | Instruction Manual - Page 49
    6. SETTING AND ADJUSTMENTS BEFORE SHOOTING 6-10 Monitoring Audio during Recording TV . ZOOM m 30 ∞ ft 10 5 7 10 15 ASPHERIC & IF 19x 3 2 5 1.5 FUJINON C 16 11 8 5.6 20 M O FILTER 1 3200k 2 5600k+1/8ND 3 5600k 4 5600k+1/64ND SHUTTER STATUS A CR MENU ALARM MONITOR AUTO IRIS FULL
  • JVC GY-DV700WUCL | Instruction Manual - Page 50
    the unit enters the record-pause mode. • Slowly close the cassette cover. • Use a videocassette marked MiniDV. • If the cassette cover is not closed, the GY-DV700W will remain inoperative. • Following loading of the cassette and when the POWER switch is turned ON/OFF, the built-in head cleaner will
  • JVC GY-DV700WUCL | Instruction Manual - Page 51
    after being pressed, the viewfinder REC indicator lamp may blink and the GY-DV700W may not enter the record mode. To remedy this condition set the the lens' iris if the iris is changed abruptly or the iris is manually moved abruptly during recording. If you find the noise annoying, please purchase
  • JVC GY-DV700WUCL | Instruction Manual - Page 52
    on the setting of the VTR switch. ● VTR switch setting STBY : The GY-DV700W enters the record-pause mode, and the drum is rotating at this time , recording starts immediately when the VTR trigger button is pressed. SAVE : The GY-DV700W enters the record-pause mode but the drum is not rotating. (Save
  • JVC GY-DV700WUCL | Instruction Manual - Page 53
    7. SHOOTING OPERATION 7-4 Checking Recorded Contents in Record-Pause Mode (Recording Check Function) 1. RET button * This function does not work when the GY-DV700W is in the save mode or stop mode. * During recording check, the following indications will appear if the error rate increases due to
  • JVC GY-DV700WUCL | Instruction Manual - Page 54
    tracking function is activated at the start of the playback mode, digital noise may appear on the playback image. • This unit does not allow manual tracking adjustment. • When playing back a tape recorded on another unit, digital noise may appear during playback. • When turning on the power with the
  • JVC GY-DV700WUCL | Instruction Manual - Page 55
    M M 8-2 Fast-Forward, Rewind 8. PLAYBACK MODE C 1166 111 8 5.5.66 2200 TTVV. .ZZOOOOMM m ∞ ftft O FILTER 1 3200k 2 5600k+1/8ND 3 5600k 4 5600k+1/64ND SHUTTER STATUS A CR MENU ALARM MONITOR AUTO IRIS FULL AUTO BLACK BACK L NORMAL SPOT L STRETCH NORMAL COMPRESS LOLUX PRST A B ON KNEE
  • JVC GY-DV700WUCL | Instruction Manual - Page 56
    9. TIME CODE OPERATION The GY-DV700W records EBU-standard time codes and user's bits. In switch REC/FREE switch CH-1 AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE MENU FRONT REAR GROUP HOLD ITEM
  • JVC GY-DV700WUCL | Instruction Manual - Page 57
    CODE OPERATION TIME CODE PRESETTING PROCEDURE 2. HOLD button 4. SHIFT button CH-1 AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE MENU FRONT REAR GROUP HOLD ITEM SELECT DATA SET SHIFT ADVANCE
  • JVC GY-DV700WUCL | Instruction Manual - Page 58
    is switched off, it continues to run on the backup lithium battery. Sync signal generator PUSH External time code generator REF Video signal DV CAMCORDER GY-DV700W REF Video signal LTC time code signal Y/C OUT MONITOR OUT LINE OUT CH-1 CH-2 TC IN TC OUT VTR REMOTE TC IN connector SYNC
  • JVC GY-DV700WUCL | Instruction Manual - Page 59
    LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE non drop frame) already recorded on the tape. 9-5 Reproducing Time Codes The GY-DV700W incorporates a time code reader. During playback, the time code or user's
  • JVC GY-DV700WUCL | Instruction Manual - Page 60
    decreases by two. • When recording in the S.S.F. mode, the reel number (cassette number) for each cassette is recorded in the memory of the GY-DV700W and on tape. • When the videocassette is replaced, new S.S.F. data is generated. S.S.F. data for six videocassettes can be stored in the internal
  • JVC GY-DV700WUCL | Instruction Manual - Page 61
    10. S.S.F. (Super Scene Finder) FUNCTION 10-2 How to Use the S.S.F. Function VF OFF ZEBRA SKIN ON AREA AUTO WHITE ACCU FOCUS VTR AUDIO LEVEL CH-1 TAKE TAKE button VTR trigger button CUE Mode 1. Set the S.S.F. mode as CUE mode. Set the VCR Setup Menu item No. 398 S.S.F. MODE to "CUE". 
  • JVC GY-DV700WUCL | Instruction Manual - Page 62
    M M 10. S.S.F. (Super Scene Finder) FUNCTION 10-3 Deleting S.S.F. Data TV . ZOOM C 16 11 8 5.6 20 m 8.7 30 ∞ ft 10 5 7 10 15 ASPHERIC & IF 19x 3 2 5 1.5 FUJINON O FILTER 1 3200k 2 5600k+1/8ND 3 5600k 4 5600k+1/64ND SHUTTER STATUS A CR MENU ALARM MONITOR AUTO IRIS FULL AUTO
  • JVC GY-DV700WUCL | Instruction Manual - Page 63
    LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE "Connecting to a PC" on page 65. Operation In the stopped condition, the GY-DV700W answers with the S.S.F. data when it receives the RS-232C command D5h "S.S.F.
  • JVC GY-DV700WUCL | Instruction Manual - Page 64
    . 3. Insert the videocassette. 4. Connect the DV cable. Memo: • When the GY-DV700W is controlled through the DV connector, set the VCR Setup Menu item No.050 approximately 2 to 3 seconds before recording starts on the GY-DV500. • When video is input through the DV connector, the EE picture is
  • JVC GY-DV700WUCL | Instruction Manual - Page 65
    DV cable. For compatible non-linear editing controller, consult with your JVC dealer. Settings • To remote control the PC or non-linear editing 050 REMOTE SELECT to "RS232C".  See page 68. • To remote control the GY-DV700W's VCR using the DV connector's IEEE1394 option, set the VCR Setup Menu item
  • JVC GY-DV700WUCL | Instruction Manual - Page 66
    12. SETUP MENU 12-1 VCR Setup Menu The setup menus for the VCR section can be set while observing the menu in the viewfinder and on the unit's counter display. The set contents are stored in the memory and retained even after the power is switched OFF. VCR SETUP MENU CONFIGURATION The VCR Setup Menu
  • JVC GY-DV700WUCL | Instruction Manual - Page 67
    VOLUME OF F 48K ENAB L E Item menu screen DATA SET DATA SET display CH-1 AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE MENU FRONT REAR GROUP HOLD ITEM SELECT DATA SET SHIFT ADVANCE PRESET
  • JVC GY-DV700WUCL | Instruction Manual - Page 68
    the VCR should RS232C be controlled using the operation buttons on the GY-DV700W only. rnSL Lc IEEE1394 : Choose this setting when the signal from the VTR Note: REMOTE connector on the GY-DV700W. • The operation buttons on the GY-DV700W remain effective even when set to IEEE1394 or RS232C
  • JVC GY-DV700WUCL | Instruction Manual - Page 69
    12-1 VCR Setup Menu (Cont'd) 12. SETUP MENU Group SYSTEM TIME CODE ON SCREEN Item Setting Value Upper row: Viewfinder display Lower row: Counter display indication 302: BACK SPACE STANDARD QUICK b-SP St qU Contents Selection of amount of back space for recording pause. STANDARD :
  • JVC GY-DV700WUCL | Instruction Manual - Page 70
    12. SETUP MENU 12-2 Camera Menu Screen Flow Camera Menu Screen Flow As illustrated below, the Camera Menu is a menu screen comprising several layers. The first layer of the CAMERA MENU screen is for choosing and setting the menus required in accordance with functions or purposes. The unit also
  • JVC GY-DV700WUCL | Instruction Manual - Page 71
    12. SETUP MENU 12-3 How to Select from the Camera Menu TV . ZOOM 30 ∞ ft 7 10 15 ASPHERIC & IF 19x 5 FUJINON C 16 11 8 5.6 20 M m O FILTER 1 3200k 2 5600k+1/8ND 3 5600k 4 5600k+1/64ND SHUTTER STATUS A CR MENU ALARM MONITOR AUTO IRIS FULL AUTO BLACK BACK L NORMAL SPOT L STRETCH
  • JVC GY-DV700WUCL | Instruction Manual - Page 72
    12. SETUP MENU 12-4 VF Display Screen Item F NO. DISPLAY Function, Operation Variation Range Initial Setting Selects whether or not the F-number of the lens iris is displayed on the Status 1 screen. ON F-number is displayed. OFF F-number is not displayed. ON OFF OFF AUDIO DISPLAY Selects
  • JVC GY-DV700WUCL | Instruction Manual - Page 73
    12-5 OPERATION Screen 12. SETUP MENU Item ASPECT RATIO Function, Operation Variation Range Initial Setting Sets the image size of the video signal. 16:9 16:9 16:9 16:9 aspect ratio image output. When this setting is selected, an 4:3 ID signal for identifying the WIDE screen mode is also
  • JVC GY-DV700WUCL | Instruction Manual - Page 74
    12. SETUP MENU 12-6 PROCESS Screen Item MASTER BLACK Function, Operation Variation Range Initial Setting Adjusts the pedestal level (master black), which is the reference of black. • To increase the pedestal level ..... Increase the number. (UP) • To decrease the pedestal level .... Decrease the
  • JVC GY-DV700WUCL | Instruction Manual - Page 75
    12-7 ADVANCED PROCESS Screen 12. SETUP MENU Item COLOR MATRIX Function, Operation Variation Range Initial Setting Sets the color matrix ON ON OFF ...... Deactivates the color matrix function OFF ON ....... The color reproducibility is enhanced, but noise increases. CAUTION: During the
  • JVC GY-DV700WUCL | Instruction Manual - Page 76
    12. SETUP MENU 12-9 FILE MANAGE Screen The unit has three files that can be used for storing camera menus. The FILE MANAGE screen is for performing the operations for saving the set CAMERA MENU. • When menu settings are made using SCENE FILE A or B, the contents of the settings will be invalid if
  • JVC GY-DV700WUCL | Instruction Manual - Page 77
    12-10 SETUP Screen 12. SETUP MENU Item H PHASE Function, Operation Variation Range Initial Setting For adjusting the horizontal phase of the unit in relation to the signal 0 128 (external sync signal) input through the SYNC IN connector on the left to side of the unit. 256 Delaying the
  • JVC GY-DV700WUCL | Instruction Manual - Page 78
    12. SETUP MENU 12-11 Resetting of Camera Menu Setting Values Using the FILE MANAGE screen, the CAMERA MENU settings can be reset to the initial setting values. On the FILE MANAGE screen, select the file of the CAMERA MENU to be reset, and then perform the resetting operation. TV . ZOOM C 16 11 8
  • JVC GY-DV700WUCL | Instruction Manual - Page 79
    13. FEATURES OF THE CAMERA SECTION 13-1 Full-Time Auto White Balance (FAW) - - - OPERAT I ON - - - SCENE F I LE A ASPECT RAT I O : 16 : 9 SHUT TER : STEP F AW : NONE GA I N L : 0dB GA I N M : 9dB GA I N H : 18dB SMOOTH TRANS : OFF PAGE BACK C 16 11 8 5.6 20 M O FILTER 1 3200k
  • JVC GY-DV700WUCL | Instruction Manual - Page 80
    be done by the following methods. • Setting the AUTO IRIS LEVEL switch of the camera  See "SWITCH FUNCTIONS" on page 83. ZEBRA PATTERN DISPLAY DURING MANUAL ADJUSTMENT OFF ZEBRA SKIN ON AREA AUTO WHITE ACCU FOCUS VTR AUDIO LEVEL CH-1 TAKE ZEBRA switch By setting the ZEBRA switch to ON
  • JVC GY-DV700WUCL | Instruction Manual - Page 81
    13. FEATURES OF THE CAMERA SECTION 13-3 Shooting the Screen Image on a Computer Monitor Video monitor Band C 1166 1111 8 5.5.66 2200 M m ∞ ftft 8.8.77 1100 3300 O FILTER 1 3200k 2 5600k+1/8ND 3 5600k 4 5600k+1/64ND SHUTTER STATUS A CR MENU ALARM MONITOR AUTO IRIS FULL AUTO BLACK
  • JVC GY-DV700WUCL | Instruction Manual - Page 82
    will increase a little because the screen becomes brighter as the ALC (Auto Level Control) function boosts the gain more than in the case of manual adjustment. This switch allows the gain to be boosted when the illumination of the subject is insufficient. Switch Position Factory-Set Gain L 0dB
  • JVC GY-DV700WUCL | Instruction Manual - Page 83
    completed. • In the FAS mode, the audio recording level is not set automatically to the AUTO mode. To select the AUTO mode, set the AUTO/MANUAL switch of the VCR section to AUTO. Ⅲ Automatic Setting Contents • If you have been displaying the color bars, the screen is switched automatically to the
  • JVC GY-DV700WUCL | Instruction Manual - Page 84
    13. FEATURES OF THE CAMERA SECTION 13-6 How to Use Skin Tone Detail The contour emphasis in the skin color areas of the video signal can be controlled and made to appear gentle and smooth. Ⅲ Setting the Color and Range of the Skin Tone Detail Function TV . ZOOM 20 m 8.7 30 ∞ ft 10 5 7 10
  • JVC GY-DV700WUCL | Instruction Manual - Page 85
    13. FEATURES OF THE CAMERA SECTION 13-6 How to Use Skin Tone Detail (Cont'd) Ⅲ Confirming the color tone area adjusted with the Skin Tone Detail function When the ZEBRA switch on the front section is pressed to the "SKIN AREA" side, the color tone areas adjusted with Skin Tone Detail are displayed
  • JVC GY-DV700WUCL | Instruction Manual - Page 86
    Troubleshooting Warnings concerning problems with Indicates dew formation (condensation). Lights in the case of troubles with the drum servo. Lights when the input sync in charge of professional video equipment at your nearest JVC-authorized service agent. Operation : Continues. Remedy : Clean the
  • JVC GY-DV700WUCL | Instruction Manual - Page 87
    14. OTHERS 14-1 Troubleshooting (Cont'd) Alarm Indications (Cont'd) Depending on the alarm conditions, the warning indicators in the LCD display, the WARNING indicator, the TALLY lamp, alarm tones and
  • JVC GY-DV700WUCL | Instruction Manual - Page 88
    14. OTHERS 14-1 Troubleshooting (Cont'd) WARNINGS IN VIEWFINDER Ⅲ Viewfinder Warning Lamps 1. Battery RET button on the lens section.) • VTR WARNING (SERVO): Lights in the case of drum servo trouble during recording. • VTR WARNING (DEW): Lights when condensation occurs in the unit. • VTR WARNING
  • JVC GY-DV700WUCL | Instruction Manual - Page 89
    Troubleshooting (Cont'd) In the case of troubles occurring during operation of the GY-DV700W problem occurs again after the power is turned ON, there may be something wrong with the GY-DV700W. Please consult the person in charge of professional video equipment at your nearest JVC-authorized service
  • JVC GY-DV700WUCL | Instruction Manual - Page 90
    Troubleshooting (Cont'd) TROUBLES WITH ERROR CODE OUTPUTS Error Code 3200 3300 4100 4200 5605 5606 to 5607 5702 5802 7001 7101 7202 to 7203 7302 to 7303 7305 Error Details GY professional video equipment at your nearest JVCauthorized service agent. Cassette housing abnormality. Operation stops.
  • JVC GY-DV700WUCL | Instruction Manual - Page 91
    14-1 Troubleshooting (Cont'd) TROUBLES WITHOUT ERROR CODE OUTPUTS Symptoms Remedy Power cannot be switched ON. Operation buttons on the GY-DV700W so, change the setting to "LOCAL". • Is the cassette cover open? The GY-DV700W remains inoperative as long as the cassette door is open. • Is switch on
  • JVC GY-DV700WUCL | Instruction Manual - Page 92
    by selecting HM (HOUR METER) on the VCR Setup Menu. Use this as a guide for periodical maintenance.  See page 7. Note: The hour meter is not shown AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE
  • JVC GY-DV700WUCL | Instruction Manual - Page 93
    temperatures : 0 °C to 40 °C Operating humidity : 30 % to 80 % RH Storage temperatures: -20 °C to 60 °C Ⅲ ACCESSORIES Microphone Tripod base Lithium battery Head cleaning tape Instructions : x1 : x1 : x 1 (CR2032) : x1 : x1 Design and specifications are subject to change without notice. 93
  • JVC GY-DV700WUCL | Instruction Manual - Page 94
    14. OTHERS 14-3 Specifications OPTIONAL ACCESSORIES Viewfinder Power zoom lens AC power adapter Microphone Microphone holder : VF-P116W : A19 x 8.7BW, A19 x 8.7B12 (FUJINON) YJ18 x 9BK12 (CANON) : AA-P250 : MV-P615 : KA-A50 EXTERNAL DIMENSIONS (unit: mm) PUSH OPEN VF OFF ZEBRA SKIN ON
  • JVC GY-DV700WUCL | Instruction Manual - Page 95
    VICTOR COMPANY OF JAPAN, LIMITED ® is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD. ® is a registered trademark in Japan, the U.S.A., the U.K. and many other countries. © 2001 VICTOR COMPANY OF JAPAN, LIMITED Printed in Japan SC96991-001 GY-DV700W DV CAMCORDER
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
GY-DV700W
SC96991-001
DV CAMCORDER
INSTRUCTIONS
* The illustration shows the GY-DV700W DV Camcorder with the optional lens viewfinder attached.
This instruction manual is made from 100% recycled paper.
For Customer Use :
Enter below the Serial No. which is located on the body.
Retain this information for future reference.
Model No. GY-DV700W
Serial No.
Thank you for purchasing this JVC product. Before operating
this unit, please read the instructions carefully to ensure the
best possible performance.
INTRODUCTION
CONTROLS,
INDICATORS AND
CONNECTORS
BASIC SYSTEM
CONNECTIONS AND
ADJUSTMENTS
POWER SUPPLY
PREPARATIONS
SETTING AND
ADJUSTMENTS
BEFORE SHOOTING
SHOOTING
OPERATION
PLAYBACK MODE
TIME CODE
OPERATION
S.S.F. (Super Scene
Finder)
USING EXTERNAL
COMPONENTS
SETUP MENU
OTHERS
FEATURES OF THE
CAMERA SECTION