Jenn-Air JXI5036WS Dimension Guide

PRODUCT MODEL NUMBERS

LOCATION REQUIREMENTS

PRODUCT DIMENSIONS

VENTING REQUIREMENTS

JXI5036W

JXI5042W

●

A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

36" (91.4 cm) and 42" (106.7 cm) Island-Mount Canopy Range Hood

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. W10274308E

12/16/09

Example

v

ent system

Non-vented (recirculating)

Roof Venting

A. Deflector

B. 8" (20.3 cm) round vent

A. Roof cap

B. 8" (20.3 cm) round vent

A

B

A

B

ELECTRICAL REQUIREMENTS

This range hood is factory set for venting through the roof.

A 8" (20.3 cm) round vent system is needed for installation (not included). The

hood exhaust opening is 8" (20.3 cm) round.

NOTE:

Flexible vent is not recommended. Flexible vent creates back pressure

and air turbulence that greatly reduce performance.

For Non-Vented (recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the outside, the hood

can be used in the non-vented (recirculating) version, using a Recirculation Kit

(which includes charcoal filters and a deflector). To order, see the “Assistance

or Service” section.

NOTE:

Wall venting can be an option for 2-story homes.

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters)

for each vent piece used in the system.

Vent Piece

8" (20.3 cm) round

45° elbow

2.5 ft

(0.8 m)

90° elbow

5.0 ft

(1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

The following example falls within the maximum recommended vent

length of 35 ft (10.7 m).

1 - 90° elbow

1 - wall cap

8 ft (2.4 m) straight

= 5.0 ft (1.5 m)

= 0.0 ft (0.0 m)

= 8.0 ft (2.4 m)

Length of system

= 13.0 ft (3.9 m)

IMPORTANT:

Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's

responsibility to comply with installation clearances specified on the

model/serial rating plate. The model/serial rating plate is located behind

the left filter on the rear wall of the vent hood.

Canopy hood location should be away from strong draft areas, such as

windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements”

section.

Because of the size and weight of this island hood, the chimney support

must be securely attached to the ceiling.

●

For plaster or drywall ceilings, the chimney support must be attached

to joists. If this is not possible, you must build a support structure

behind the plaster or drywall. The support structure must be able to

support 80 lbs (36.6 kg).

The range hood is factory set for venting through the roof or wall.

For non-vented (recirculating) Installation see “Non-vented (recirculating)

Installations” in “Install Range Hood” section. Recirculation Kit Part

Number W10272065 is available from your dealer or an authorized parts

distributor.

All openings in ceiling and wall where range hood will be installed must

be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured

Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly

the Federal Standard for Mobile Home Construction and Safety, Title 24,

HUD, Part 280) or when such standard is not applicable, the standard for

Manufactured Home Installation 1982 (Manufactured Home Sites,

Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or

with local codes.

Page 1 of 2

Jenn-Air JXI5036WS Dimension Guide

Jenn-Air JXI5036WS Manual

Jenn-Air JXI5036WS manual content summary: