Kenmore 4810 Installation Instructions
Kenmore 4810 - 3.5 cu. Ft. I.E.C. High-Efficiency Washer Manual
 |
View all Kenmore 4810 manuals
Add to My Manuals
Save this manual to your list of manuals |
Kenmore 4810 manual content summary:
- Kenmore 4810 | Installation Instructions - Page 1
Requirements Water Supply Requirements Drain Requirements Rough-In Dimensions Location Of Your Washer Unpacking Installation Replacement Parts PAGE 2 2 2 2 2 3 4 4-5 5-6 6 Installation and service must be performed by a Sears, Roebuck and Co., qualified installer, service agency or the gas - Kenmore 4810 | Installation Instructions - Page 2
this washer with washer . . The washer MUST be grounded your washer is is the owner's responsibility cm) of your washer's water inlet. The water pressure. DRAIN REQUIREMENTS I. Drain capable of eliminating cm) Min. l II NOTE: Drain hose attached to the washer can reach a 90 in. (229 cm) - Kenmore 4810 | Installation Instructions - Page 3
" Cord 33 . 40 (84 8) inches(cm) NOTE: For pedestal installations, see additional installation instructions included with the pedestal. For stacking installations, see additional installtion instructions included with the stacking kit. For under counter installations, no special top is required - Kenmore 4810 | Installation Instructions - Page 4
temperature should never be below 60 ° F (15.6 ° C) for proper washer (detergent breakdown) operation. 2. In an area where it will come in contact 0 in. (0 cm) Top = 0 in. (0 cm) When installed in closet: Front = I in. (2.54 cm) Closet door ventilation required: 2 Iouvered openings each 60 in2 - Kenmore 4810 | Installation Instructions - Page 5
washer in it's final position, place a level on top of the washer. Adjust the leveling legs so the washer is level front-to-rear and side-to-side, and stable comer-to-corner. Washer new hoses. 2. For pedestal installations, See additional installation instructions included with the pedestal. - Kenmore 4810 | Installation Instructions - Page 6
washer does not operate, please review the "Avoid Service Checklist" in your Owner's Guide before calling for service. 12. Placethese instructions in a location near the washer the washer. Cable Tie REPLACEMENT PARTS If replacements parts are needed for your washer, call Sears Parts and Service
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
®
Full Size Tumble
Action
Washers
Before
beginning
installation,
carefully
read
these
instructions.
This
will
simpfify
the
installation
and
ensure
the
washer
is installed
correctly
and
safely.
Leave
these
instructions
near
the
washer
after
installation
for
future
reference.
NOTE:
The
electrical
service
to
the
washer
must
conform
with
local
codes
and
ordinances
and
the latest
edition
of the
National
Electrical
Code,
ANS!/NFPA
70.
For your safety the information
in
this manual must be followed
to minimize
the risk
of fire or explosion or to prevent property
damage,
personal
injury or loss of life.
- Do not store or use gasoline or other flammable
vapors
and
liquid
in the vicinity
of this or any
other appliance.
-
WHAT
TO DO IF YOU
SMELL GAS
•
Do not try to light any appliance.
•
Do not touch
any electrical
switch;
do not
use any phone
in your
building.
•
Clear the room,
building
or area of all
occupants.
•
Immediately
call your gas supplier from
a
neighbor's
phone.
Follow the gas suppliers
instructions.
•
If you cannot
reach your gas supplier, call
the fire department.
Installation
and service must
be performed
by a
qualified
installer,
service
agency
or the
gas
supplier.
Printed in U.S.A.
Contents
S UBJECT
PAGE
Pre-lnstallation Requirements
2
Electrical Requirements
2
Grounding Requirements
2
Water Supply Requirements
2
Drain Requirements
2
Rough-In Dimensions
3
Location Of Your Washer
4
Unpacking
4-5
Installation
5-6
Replacement Parts
6
Sears,
Roebuck
and
Co.,
Hoffman
Estates, IL
60179 U.S.A.
_N 134906800(0706)