Kenmore 8875 Owners Manual
Kenmore 8875 - 24 in. Laundry Center Manual
 |
View all Kenmore 8875 manuals
Add to My Manuals
Save this manual to your list of manuals |
Kenmore 8875 manual content summary:
- Kenmore 8875 | Owners Manual - Page 1
Owner's Manual and Installation Instructions ® 24-Inch Wide LAUNDRY CENTER Washer • Electric Dryer IMPORTANT: Read and follow all safety and operating instructions before first use of this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. PART NO. 3405593 PRINTED IN U.S.A. - Kenmore 8875 | Owners Manual - Page 2
40 OPERATING INSTRUCTIONS - DRYER 46 LAUNDRY TIPS 5O REMOVING STAINS 53 CARING FOR YOUR LAUNDRY CENTER 56 TROUBLESHOOTING - WASHER 60 TROUBLESHOOTING - DRYER 64 SEARS MAINTENANCE AGREEMENT 66 Please read this manual. It will help you install and operate your new Kenmore Laundry Center - Kenmore 8875 | Owners Manual - Page 3
from the date of purchase, if this laundry center is installed and operated according to the instructions in this manual, Sears will repair or replace any of its mechanical or electrical parts if they are defective in material or workmanship. NOTE: Exhausting your laundry center with a plastic vent - Kenmore 8875 | Owners Manual - Page 4
the washing machine. This will release any accumulated hydrogen gas. Because the gas is flammable, do not smoke or use an open flame during any part of the laundry center or attempt any servicing unless specifically recommended in the Owner's Ivlanual or in published userrepair instructions that - Kenmore 8875 | Owners Manual - Page 5
INSTALLATION OVERVIEW For a complete list of tools and parts needed, see pages 5-10. A. SELECT LOCATION FOR YOUR LAUNDRY CENTER (pgs. 11-16) LaundryTub Drain System (p. 12) Standpipe Drain System (p. 13) Floor Drain System (p. 13) Recessed Area/'Closet Installation Instructions (pgs. 14-15) i - Kenmore 8875 | Owners Manual - Page 6
B. INSTALL LEVELING LEGS (p. 17) Parts Needed: (supplied with laundry center) 2 rear leveling legs 2 front leveliqg legs C. REMOVE STYROFOAM PACKING (p. 17) Yellowcard - Kenmore 8875 | Owners Manual - Page 7
D. MAKEELECTRICALCONNECTIO(Npgs.18-28) If using a powercord: Tools Needed: Parts Needed: V4-inch nut driver (shown) or socket wrench #2 Phillips head screwdriver _, Strain relief Flashlight (optional depending on installation) New 3- or 4-wire, 30-amp. U.L.-listed - Kenmore 8875 | Owners Manual - Page 8
(pgs. 29-30) Tools Needed: PUSH Parts Needed: (supplied with laundry center) Pliers that open to 19/'6 inches f_l_-_ Flashlight (optional Tools Needed: Su Pliers that open to 19/%inches ..j---'_ \ \,_ Flashlight (optional depending on installation) 7 Parts Needed: (supplied with laundry - Kenmore 8875 | Owners Manual - Page 9
G. CONNECT INLET HOSES TO WATER FAUCETS (p. 31) Tools Needed: Pliers that open __ to1%6 inches _ OR_' ,uc e, (optional depending on installation) Flashlight (optional depending on installation) Parts Needed: (supplied with laundry center) 2 water inlet hoses H. SECURE DRAIN HOSE (p. 32) ( - Kenmore 8875 | Owners Manual - Page 10
(p. 33) Tools Needed: /16-inch open-end wrench Flashlight (optional depending on installation) Wood block J. CONNECT EXHAUST (pgs. 33-38) Parts Needed: (Supplied with laundry center) 2 front leveling legs with nuts Tools Needed: !_t-± i I Parts Needed: Tin snips Y Flashlight (optional - Kenmore 8875 | Owners Manual - Page 11
cycles requires temperatures above 32°F (at lower temperatures, some water may remain in washer). See page 59 for Winterizing Information. Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Failure to do so can result in death, explosion, or tire. • Proper - Kenmore 8875 | Owners Manual - Page 12
fill valves attached to the back of the laundry center Laundry tub drain system: Needs a minimum 20-gallon laundry tub. Support: Floor must be sturdy enough to support a total weight of 500 pounds (includes laundry center and load weight) Level floor: Maximum allowable slope under entire laundry - Kenmore 8875 | Owners Manual - Page 13
or utility sink and sump pump (available from local plumbing suppliers) Siphon break, Part No. 285320; additional drain hose, Part No. 3357090; and connector kit, Part No. 285442 Parts listed are available from your local Sears store or Sears Service Center. Call 1-800-366-PART (1-800-366-7278). - Kenmore 8875 | Owners Manual - Page 14
DIMENSIONS Most installations will require at least 5-inch clearance behind the dryer for the dryer vent. Location must be large enough to fully open dryer door. • Proper operation of washer of fire, this appliance must be exhausted outdoors. NOTE: No fuel burning appliances may be installed in - Kenmore 8875 | Owners Manual - Page 15
servicing. • If closet door is installed, the minimum air openings in top and bottom are required. Louvered doors with equivalent air openings least the minimum dimensions indicated. O oo oO _t_ 6" -T- **48 ._;qi.n._ minimum ventilation ar_.=a 4, 3" 7 "1"'--_ I _-237/e"-_ I - Kenmore 8875 | Owners Manual - Page 16
in washer). See page 59 for Winterizing Information. • Proper ,operation of dryer cycles requires temperatures above 45°F (at lower temperatures, the dryer may , Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Homes Construction and Safety, Title 24, HUD Part 280). • Laundry center - Kenmore 8875 | Owners Manual - Page 17
they snap into place. To install front Ilegs: STEP 1. Screw front legs into the holes in the triangular braces in front corners. Screw them in with an close to its final location. STEP 1. Open the washer lid. The latch under the dryer will keep the lid open. Read, then remove the yellow card on - Kenmore 8875 | Owners Manual - Page 18
power supply cord.* GoTo Page 19-1. A fused disconnect or circuil breaker box.* 21 - II. 4-wire electrical receptacle (NEMA Type 14-30R) 4-wire direct A U.L.-listed, 120!240-volt minimum, 30-amp., dryer power supply cord. 24 - III. J A fused disconnect or 27 - IV. circuit breaker box. *If - Kenmore 8875 | Owners Manual - Page 19
connections. Failure to follow these instructions can result in death, fire, or electrical shock. Local codes may permit the use of a U.L.-listed, 120/240-volt minimum, 30-ampere, dryer power supply cord kit (pigtail). Power supply cord should be type SRD or SRDT and be at least four feet - Kenmore 8875 | Owners Manual - Page 20
INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric hole below terminal block opening. Strain relief should have the laundry center rear panel. Secu re cover with - Kenmore 8875 | Owners Manual - Page 21
(gold). Securely tighten all electrical connections. Failure to follow these instructions can result in death, fire, or electrical shock. GROUNDING INSTRUCTIONS This appliance must be connected to a grounded of slack in the line so laundry center can be moved if servicing is ever necessary. 21 - Kenmore 8875 | Owners Manual - Page 22
Securely l:ighten all electrical connections STEP 3. Attach a 3/,-inch, U.L.-listed, strain relief to the hole below terminal block opening. Strain relief of a frame-grounding conductor to the neutral wire, see the instructions on page 23. Otherwise, proceed with Installation on page ;.>9. Neutral - Kenmore 8875 | Owners Manual - Page 23
the other two wires to outer terminal block screws. Securely tighten all electrical conections. STEP 5. Tighten the strain rellief screws. STEP 6. Insert tab of terminal block cover into slot of the laundry center rear panel. Secure cover with hold-down screw. STEP 7, Connect separate copper - Kenmore 8875 | Owners Manual - Page 24
codes may permit the use of a U.L.-listed, 120/240wolt minimum, 30-ampere, dryer power supply cord kit (pigtail). Power s_,Jpptycord should be type SF:{Dor SRr)T Securely tighten all electrical connections. Failure to follow these instructions can result in death, fire, or electrical shock. Neutral - Kenmore 8875 | Owners Manual - Page 25
INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric listed, strain relief to the hole below terminal block opening. Strain relief should have a tight fit with - Kenmore 8875 | Owners Manual - Page 26
(green) of the power supply cord to the external grounding conductor screw. Securely tighten all electrical connections. STEP 8. Insert tab of terminal block cover into slot of the laundry center rear panel. Secure cover with hold-down screw. Proceed with Installation on page 29. Neutralwire (white - Kenmore 8875 | Owners Manual - Page 27
appliance. Fire Hazard Use 10 gauge solid copper wire. Use UL approved strain relief. Disconnect power before making electrical electrical connections. Failure to follow these instructions can result in death, fire, or electrical if servicing is ever necessary. STEP 2. Remove hold - Kenmore 8875 | Owners Manual - Page 28
end o the wire over the terminal block screw. The open side of the hook should face to the right. Squeeze grounding conductor screw. Securely tighten all electrical connections. External ground connector STEP 5. into slot of the laundry center rea_ panel. Secure cover with hold-down screw. - Kenmore 8875 | Owners Manual - Page 29
following instructions: pliers to open. Place clamp Part No. 388423 and hose kit, Part No. 285442 Drain hose that is too long Hose kit, Part N,a. 285442 A problem with lint clogging your drain Drain protector, Part No. 367031 Parts listed are available from your local Sears store or Sears Service - Kenmore 8875 | Owners Manual - Page 30
standpipe or laundry tub drain systems: STEP 2. Open yellow, single-wire clamp with pliers and slide with a permanent marker. STEP 1. Insert one new, flat washer (from the parts bag) into each end of the inlet hoses. Check that washers are firmly seated in couplings. wFaslahter Hose coupling 3O - Kenmore 8875 | Owners Manual - Page 31
valves. G. CONNECT INLET HOSES TO WATER FAUCETS STEP 1. Make sure washer basket is empty. Run water through both faucets into a bucket or hoses, Part No. 76314 or 10 ft. hoses, Part No. 350008 Parts listed are available from your local Sears store or Sears Service Center. Call 1-800-366-PART (1-800 - Kenmore 8875 | Owners Manual - Page 32
inlet hoses (not the handles or stems). Secure plastic strap. STEP 1. Move laundry center to its final location. STEP 2. Use the plastic strap from the parts bag to wrap the drain hose together with the laundry tub or standpipe. Secure plastic strap. 32 - Kenmore 8875 | Owners Manual - Page 33
on top of the washer, first side-to-side; then front-to-back. J. CONNECT vent. Failure to follow these instructions can result in death or fire. WARNING: To reduce the risk of fire, this dryer must be exhausted outdoors. • use the hose attachment on your vacuum or, use a pole or wire with a feather - Kenmore 8875 | Owners Manual - Page 34
Kit No. 3391335 (white) Side Exhaust Kit No. 3391336 (almond) Follow the instructions in the kit to avoid operational and personal hazards. These kits are available at your local Sears store or Sears Service Center. Rear exhaust installations for standard offset connections -_[see pgs. 36-37 - Kenmore 8875 | Owners Manual - Page 35
DETERMINE VENT LENGTH Maximum Exhaust Lengths: • Rear Exhaust. The maximum length of the rear exhaust system depends on the type of vent, the number of elbows and the type of exhaust hood. Refer to the chart below. • Side Exhaust. Side exhaust adds a 90 ° turn inside the laundry center. To determine - Kenmore 8875 | Owners Manual - Page 36
final location, check to make sure the i STEP 2 laundry center is still level (see section i Elbow "1','LEVEL LAUNDRY CENTER). Exhaust Finish Installation. See "REVIEW hood INSTALLATION" on page 39. The vent usually comes in 2-foot lengths. Use tin snips to cut the vent 3 inches longer than your - Kenmore 8875 | Owners Manual - Page 37
the other end to the exhaust hood. Tape joints and tighten clamps. / Ct!® Tape m Clamp Dryer Fheleaxviyble .-.-Wall Elbow J (optional) Duct _.. tape & clamps STEP 6. Stretch the vent only as section "1','LEVEL LAUNDRY CENTER). Finish Installation. See "REVIEW INSTALLATION" on page 39. 37 - Kenmore 8875 | Owners Manual - Page 38
, you will find it helpful to install the exhaust vent by using a loop system. A kit is available from your local Sears store or Sears Service Center. NOTE: Vent systems come in many varieties. Select the type that best fits your installation, Three of the most common types of installations are - Kenmore 8875 | Owners Manual - Page 39
. F] Start the washer and allow it to complete the HEAVY DUTY Cycle. r-] Start the dryer and allow it to complete a full heat cycle (not the AIR DRY Cycle). After five minutes, open dryer door, You should feel heat inside the dryer. If you do not feel heat, see Troubleshooting information on pages - Kenmore 8875 | Owners Manual - Page 40
follow these instructions can result in death, explosion, or fire. STARTING YOUR WASHER STEP 1. Acid measured detergent directly into washer basket. Then place a load of sorted clothes in the washer. STEP 2. Cl.3se washer lid. STEP 3. Set WATER LEVEL Control O based on tl_e size of your wash load - Kenmore 8875 | Owners Manual - Page 41
WATER TEMPERATURE CONTROL Your washer lets you select a wash and rinse water temperature setting based on the type of load you are washing. • Using warm rinse , greasy soils and stains • Prevents gray= or yellowing • Best for model atel! soiled to lightly soiled items • Safe for most fabris finishes - Kenmore 8875 | Owners Manual - Page 42
(SHORT if indicated). NOTE: Do not wash garments labeled Hand Wash in your washer. Garments that are labeled Hand Wash have: ° A fiber or construction that to 8 minutes of wash time with a pause and soak part way through for more gentle care of lightly soiled delicate items. Wash combines slow speed - Kenmore 8875 | Owners Manual - Page 43
When using extra detergent for heavily soiled clothes, or washing special-care items, you may find an extra rinse and PERMANENT PRESS Cycle. STEP 4. Pull Cycle Selector Control (Timer) Knob out to start washer. HEAVY DUTY PERMANENT PRESS SPIN ONLY A drain and spin may help shorten drying times - Kenmore 8875 | Owners Manual - Page 44
hear and what causes them. During Wash When you select a small load size setting for a small wash load, your washer has a lower water level. With . i Kenmore's DUAL-ACTION'" Agitator gives you flexible fabric care for even your largest loads. The best cleaning action in your washer takes place - Kenmore 8875 | Owners Manual - Page 45
Pause Spin KNIT/DELICATE t--ill to selected level Wash Pause Wash Fill for cool down Wash Fill to selected level Rinse [)rain no spin Spin no spin Spin Off Drain no spin Spin Off PREWASH Fill to selected level Wash selected time Drain no spin Spin Fill to selected level Rinse Drain no spin - Kenmore 8875 | Owners Manual - Page 46
, away No washer can completely remove oil. from dryer. Do not dry anything that has ever i Do not dry anything that has ever had any type of oil on it (including had anything flammable on it (even cookin£! oils). after washing). Failure to follow these instructions Items containing foam - Kenmore 8875 | Owners Manual - Page 47
• Use this cycle for most loads of knitted, delicate, or sheer fabrics. Clothes are dried at low heat. When the dryness selected is reached, the dryer goes into a 5-minute (approx.) cool-down period.. CYCLE DE-'SCRIPTIONTIMED DRY CYCLES TIMED DRY CYCLE \ Use this cycle to get up to 50 minutes of - Kenmore 8875 | Owners Manual - Page 48
. Use the AIR DRY Cycle, or place the items on a line or rack to air dry. Type of Load DELICATE FABRICS Sheer curtains (2 or 3 panels), gauze, lace, elc. RUBBER, PLASTIC, HEAT-SENSITIVE FABRICS Foam rubber- Pillows, padded bras, stuffed toys • Make sure coverings are securely stitched. • Shake and - Kenmore 8875 | Owners Manual - Page 49
like balls on the surface of garments. Pilling is the natural result of washing and wearing ot garments. PUSH TO START DRYER BUTTON Use this control to start the dryer. Be sure the dryer door is closed. Opening the door stops the dryer. It will not start again until you close the door and press the - Kenmore 8875 | Owners Manual - Page 50
hems, and seams. • Check garments for spots and stains left after washing. Do not tumble these items. Heat may permanently set stains. • Check pockets before washing or drying. Sharp or metal objects can damage your washer interior or dryer drum. Do not lay these objects on your laundry center; they - Kenmore 8875 | Owners Manual - Page 51
and wrinkle-free results. Items should sink and reappear later. • Load washer properly and select correct water level setting. Overloading or packing the machine, and selecting a setting too small for the wash load can: • cause poor cleaning • increase wrinkling • create excessive lint • wear - Kenmore 8875 | Owners Manual - Page 52
airflow. USING DRYER FABRIC SOFTENERS Dryer fabric softeners are recommended for reducing static cling. Always follow package instructions carefully. • full loads only. Do not overdry. • Avoid overloading dryer, adding wet items to a partly dried load, or openin the door unnecessarily. • Shorten - Kenmore 8875 | Owners Manual - Page 53
REMOVAL GUIDE Alcoholic beverage These stains turn brown with age, so treat immediately. Sponge or soak fresh stains witt', cold water. Wash. operated dry cleaning machine. Cream, milk, or ice cream Sponge wi:h a nonflammable fabric cleaner, or a prewash soil and stain remover. Rinse. Wash. Repeat if - Kenmore 8875 | Owners Manual - Page 54
Test first on inside seam or hem. Some rust removers are not washer safe. Follow package directions. Ketchup or tomato products Sponge immediately with a nonflammable fabric cleaner or apply a prewash soil and stain remover. Rinse. Wash. If stain remains, apply a liquid detergent to stain or soak in - Kenmore 8875 | Owners Manual - Page 55
. Mildew may form if wet or damp laundry remains in your washer for extended periods of time. To prevent mildew, promptly dry laundry after washing. Mustard Treat immediately. Scrape off excess mustard. Sponge with a nonflammable fabric cleaner or a prewash soil and stain remover. Rinse. Work liquid - Kenmore 8875 | Owners Manual - Page 56
center can extend its life and help you avoid costly service calls. CLEANING YOUR WASHER EXTERIOR Wipe up detergent, bleach, and other spills with sharp metal objects on or in your dryer. They can damage the finish. INTERIOR Explosion Hazard Use nonflammable cleaners. Failure to do so can result in - Kenmore 8875 | Owners Manual - Page 57
(polyester and cotton blends) may shed more lint than other towels, ca using your dryer"s lint screen to fill up faster. Be sure to _emove lint from the lint screen before and after drying new towels. Wash Lint Screen As Needed Laundry detergents and fabric softeners can cause a residue buildup on - Kenmore 8875 | Owners Manual - Page 58
on dryer usage. Cleaning should be done by a qualified service person. instructions can result in death or electrical shock. STEP 1. Disconnect power. STEP 2. Remove back panel by removing the screws along the frame. STEP 3. Remove lint from the dryer base with dusting brush or vacuum cleaner - Kenmore 8875 | Owners Manual - Page 59
mix the antifreeze and water. Some of the mixture will pump out while the washer spins. 5. Disconnect power. To use laundry center again: 1. Flush water due to a water pressure surge) while you are away. • Wash dryer lint screen. MOVING CARE • Disconnect power. • Make sure leveling legs are - Kenmore 8875 | Owners Manual - Page 60
eepage68. Checkthesetablesfor commonlaundry Problem Possible Cause Solution Washer Leaks Household plumbing drain, Lid is open. Drain hose is more than 96 inches above floor. 3traighten or unplug hose (see "INSTALLAIION'_ Section E). ,&tier a wash or rinse, the washer will drain without - Kenmore 8875 | Owners Manual - Page 61
into standpipe. Drain hose taped into standpipe. Washer Makes Load is unbalanced. Noise Laundry center is not level. Floor not strong enough to support laundry center. Gears engaging after drain and before spin. Upper part of agitator clicks during wash. Won't Fill/ Won't Rinse/ Won't Agitate - Kenmore 8875 | Owners Manual - Page 62
Problem Machine Stops Agitator Not Working Water Level Too Low/Not Completely Filling Tub is Crooked Lint on Load Possible Cause Solution Power cord not plugged in. Plug in power cord. .. No power at plug. Check electrical source or call electrician. Fuse blown or circuit breaker open washer. - Kenmore 8875 | Owners Manual - Page 63
directly on load. Wipe up bleach spills. Clean out pockets before washing. Zip zipaers before washing. Items damaged before washing, Mend rips and broken threads in seams before washing. Improper use of fabric softener in washer or dryer, Dilute fabric softener and add to deep rinse only. Iron - Kenmore 8875 | Owners Manual - Page 64
J:__.-*_ _.'4 :_:i Problem Not Drying Satisfactorily Dryer Will Not Run Possible Cause Solution Lintscreen is clogged with lint. Restricted air movement Exhaust vent or outside exhaust hood is clogged with lint. Exhaust vent is crushed or kinked. (;lean lint screen. Run dryer for 5-10 minutes - Kenmore 8875 | Owners Manual - Page 65
garment quality. Manufacturer's care label instructions not followed, Overloading. Overdrying. Odors Unusual Sounds Load left in dryer at the end of cycle, Household chemicals, paint, or varnish being drawn into dryer. First use of dryer element (electric only). Thumping of rollers when laundry - Kenmore 8875 | Owners Manual - Page 66
that you can depend on Sears for service. Your Kenmore Laundry Center has added value when you consider that Sears has service units nationwide, staffed with professional technicians trained on all appliances Sears sells. They have the knowledge and skills, tools, parts, and equipment to ensure our - Kenmore 8875 | Owners Manual - Page 67
- Kenmore 8875 | Owners Manual - Page 68
a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 pm, Monday- Saturday 1-800-827-6655 When requesting service or ordering parts, always give the following information: • Product Name • Part Name • Model Number • Part Number SWAR, America's Repair Specialists 68
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
 |
 |
Owner's Manual and
Installation
Instructions
24-Inch Wide
®
LAUNDRY
CENTER
Washer
•
Electric Dryer
IMPORTANT:
Read and follow
all safety
and operating
instructions
before
first use
of this product.
Sears,
Roebuck
and Co., Hoffman
Estates,
IL 60179
U.S.A.
PART
NO.
3405593
PRINTED
IN
U.S.A.