Kenwood 6020 Instruction Manual
Kenwood 6020 - DPX Radio / CD Manual
 |
View all Kenwood 6020 manuals
Add to My Manuals
Save this manual to your list of manuals |
Kenwood 6020 manual content summary:
- Kenwood 6020 | Instruction Manual - Page 1
DPX-6020 DOUBLE DIN SIZED CD/CASSETTE RECEIVER INSTRUCTION MANUAL Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new double din sized CD/cassette receiver. For your records Record the - Kenwood 6020 | Instruction Manual - Page 2
Cassette Tapes 13 Using Dolby B Noise Reduction 13 Switching Tape Types 13 Using Direct Program Search System (DPSS 14 Using DPSS with Remote 14 Blank Skip 14 Index Scan 15 Music Repeat 15 Switching Display 15 CD Kenwood 30 Security Code 31 Troubleshooting Guide 42 Specifications 46 -2- - Kenwood 6020 | Instruction Manual - Page 3
, refer to the manual for your CD-R/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs recorded on CD-R or CD-RW. • If you experience problems during installation, consult your Kenwood dealer. DISP Reset - Kenwood 6020 | Instruction Manual - Page 4
designed for use in car audio systems. Cleaning the CD Slot As dust tends to accumulate in the CD slot, clean it every once in a while. Your CDs can get scratched if you put them in a dusty CD the modifications are expressly approved in the instruction manual. The user could lose the authority to - Kenwood 6020 | Instruction Manual - Page 5
. Detailed handling instructions will appear on the CD-R or CD-RW package: read this information carefully before using the disc. • Do not stick tape on either side of the CD. Tape Do Not Load CD Accessories Do not use commercially available CD accessories that can be loaded into the CD slot, such - Kenwood 6020 | Instruction Manual - Page 6
ANGLE∞ AM Switching Modes Switching Modes: Each time you press the SRC (source) button, the mode switches as follows: ▼ Tuner mode ▼ Tape mode ▼ CD mode ▼ External disc control mode ▼ Standby mode Selecting standby mode: Press the SRC button repeatedly and switch to "ALL OFF". When "ALL OFF" is - Kenwood 6020 | Instruction Manual - Page 7
Volume Increasing Volume: Press the 5 button to turn up the volume. Decreasing Volume: Press the ∞ button to turn down the volume. Attenuator This function allows you to turn down the volume quickly. Turning Attenuator On/Off: Press the ATT button to switch the attenuator on and off. When the - Kenwood 6020 | Instruction Manual - Page 8
English General features Panel Angle Adjustment You can adjust the panel angle for easy viewing. Sliding the panel: Press the ANGLE∞ button. Each time you press the ANGLE∞ button, the panel will slide one step at a time.The faceplate angle can be varied in up to ten steps. NOTE If the power is - Kenwood 6020 | Instruction Manual - Page 9
. Press the 4 button to seek lower frequencies. • Manual Tuning Press the ¢ button to increase the frequency by one step. Press the 4 button to decrease the frequency by one step. NOTE •The ST indicator lights up when stereo broadcasts are being received. • Please see the function set system about - Kenwood 6020 | Instruction Manual - Page 10
Reception System Circuit (CRSC) Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the 0. NOTE You cannot enter frequencies above or below what a band can receive. Cancelling Direct Access Tuning: Press the DIRECT button again. Switching Display - Kenwood 6020 | Instruction Manual - Page 11
Station Name Preset (SNPS) You can assign names to radio stations with the Station Preset Memory. Up to 30 stations can be assigned names. 1 Adjust the frequency to the station whose name you want to enter. NOTE This function cannot be available during the clock display. 2 Press the NAME button for - Kenwood 6020 | Instruction Manual - Page 12
Canceling mode during input: Press the SBF button for at least one second. The station name preset play mode is canceled. Cassette player features CASSETTE EJECT 4¢ FM DISP 38 DISP SRC B.S indicator B NR B.S MTL AM SCN REP SCN indicator - 12 - indicator Mode display B NR indicator - Kenwood 6020 | Instruction Manual - Page 13
, insert in the slot. The front panel will close, and the tape will start playing. The indicator lights up when a cassette has been loaded. Playing Cassettes Already Loaded: Press the SRC (Source) button repeatedly to select the tape mode. "TAPE" is displayed when the tape mode has been selected - Kenwood 6020 | Instruction Manual - Page 14
Cassette player features English Using Direct Program Search System (DPSS) Skip forward or backward to other tracks during playback. Skipping to Beginning of Current Track or - Kenwood 6020 | Instruction Manual - Page 15
Index Scan Successively plays the first 10 seconds of each track on the tape. Turning Index Scan On/Off: Press the SCN button to switch index scan on/off. The SCN indicator lights up when index scan is turned on. Stopping to Listen to the Track Being Scanned: Press either the SCN or 38 button. - Kenwood 6020 | Instruction Manual - Page 16
one is already there. • The eject function will operate even if the CD EJECT button is pressed while no CD is loaded. Attempting to quickly insert a CD at this time may result in scratching the CD. Wait a short time before inserting a CD. • When the front panel has been slid, it might interfere with - Kenwood 6020 | Instruction Manual - Page 17
and then reinsert it. Playing Other Disc mode This function permits the connection of optional players and the playing of discs other than the loaded CD (in the current unit). Playing Discs: Press the SRC button repeatedly to select the external disc control mode. The disc will start playing. NOTE - Kenwood 6020 | Instruction Manual - Page 18
CD/External disc control features English Fast Forwarding and Reversing Disc Play the displayed disc number increases by one. Play starts at the beginning of the displayed disc. NOTE "LOAD" is displayed when discs are being exchanged on the disc changer. Making a Reverse Track Search: Press the - Kenwood 6020 | Instruction Manual - Page 19
NOTE You cannot use the direct track search function while doing track or disc scans or using random or magazine-random play. Track / Disc Repeat Repeat playing the track or the disc currently being listened to. Turning Repeat Play On/Off: Press the REP button to switch repeat track/disc play on - Kenwood 6020 | Instruction Manual - Page 20
CD will begin. NOTE This function is not available with the following models: KDC-C200/C300/C400/C301/C401 2 To change the track being heard, press . • The time needed for random selection depends on the number of discs loaded in the disc magazine. Random Play Play all the tracks on the current - Kenwood 6020 | Instruction Manual - Page 21
track title. The display of the text will be scrolled repeatedly. To scroll manually: 1 Press the DISP button to display the disc title or the track "No Access/No Disc" will be displayed when a disc has not been loaded. Rapid display (forward / reverse): Press the DISC+ or DISC- button. Pressing - Kenwood 6020 | Instruction Manual - Page 22
name you want to preset. NOTE • This function is available only for the CD player of this unit and disc changers that feature the Disc Name Preset function. NOTE • Up to 8 characters and 50 disc names can be registered in CD mode and external disc control mode. 51st Disc Name Preset is made, the - Kenwood 6020 | Instruction Manual - Page 23
DSP features 4¢ FM DISP DSP/OFF #2 COMP POSI/ AM #1 #3 SFC R.SIZE - 23 - Sound field control name DSP indicator - Kenwood 6020 | Instruction Manual - Page 24
English DSP features DSP (Digital Signal Processor) A DSP is a device which uses digital control to correct the audio signal and produce sound effects that can compensate for the small passenger compartment of a vehicle. The DSP indicator lights up when the DSP is on. Turning the DSP On: Press the - Kenwood 6020 | Instruction Manual - Page 25
, the room size switches as follows; "Room Large" (For large vans or RVs, etc.) j "Room Medium"(For sedans, etc.) j "Room Small" (For compact cars, etc.) Position Setting This function can set the DSP effects for various listening positions. 1 Press the DSP button. "DSP CTRL" is displayed once the - Kenwood 6020 | Instruction Manual - Page 26
English DSP features Graphic Equalizer features DSP Setting Preset Memory Up to three sets of the DSP settings and conditions you adjusted can be stored in the memory, and then you can recall them with the single touch of a button. 1 Press the DSP button. "DSP CTRL" is displayed once the DSP - Kenwood 6020 | Instruction Manual - Page 27
curves can be stored in the memory, and then you can recall that equalizer curve with a single touch of a button. Preset Equalizer (KBS - Kenwood Built-in Sound) Selection You can choose the equalizer from five settings whose sound qualities are preset to match music or vehicle characteristics - Kenwood 6020 | Instruction Manual - Page 28
English Graphic Equalizer features Spectrum Analyzer Display Selection You can select the display to enjoy sounds with eyes. Switching the Preset Spectrum Analyzer Display: 1 Press the EQ button. "EQ CTRL" is displayed once the Graphic equalizer mode is entered. 2 Press the DISP button. The - Kenwood 6020 | Instruction Manual - Page 29
Function set system 4¢ DISP 38 SRC FNC #1 #2 #3 #4 Function Set System FM To accommodate a greater number of functions, a function set system has been employed for making settings. Press the FNC button to enter the function set mode and then display the function to make the setting. 1 Select - Kenwood 6020 | Instruction Manual - Page 30
English Function set system Function items in Standby mode: 1. Touch Sensor Tone This function produces a beep sound that accompanies button operation. It can be switched on or off. Display and setting "BEEP On" "BEEP Off" 2. Switching Preout Switch the preout between the rear and non-fading. When - Kenwood 6020 | Instruction Manual - Page 31
be possible to cancel this function afterwards. 1 Select the four digits to use in your security code. NOTE The four-digit security code is very important, as you will need it to turn the unit on again when the code security function is on. Choose the number carefully and do not forget it (write it - Kenwood 6020 | Instruction Manual - Page 32
Function set system English Function items in Other mode: 1. Frequency Setting of High Pass Filter for Front Output You can select the frequency to be cut of the high pass - Kenwood 6020 | Instruction Manual - Page 33
manual tuning is selected. Display and setting "Auto Seek": auto seek mode "Manual Seek": manual tuning mode 11. Auto Memory Entry You can automatically store all the receivable plays the last station received. - Kenwood 6020 | Instruction Manual - Page 34
not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries: Use two "AAA"-size batteries. Slide the cover provided batteries are intended for use in operation checking, and their service life may be short. • When the remote controllable distance becomes short - Kenwood 6020 | Instruction Manual - Page 35
the - button to turn the volume down. • SRC button Each time you press the SRC button, the mode switches as follows: ▼ Tuner mode ▼ Tape mode ▼ CD mode ▼ External disc control mode ▼ Standby mode NOTE • The mode switches to the next mode from any mode which cannot be used. • The external disc - Kenwood 6020 | Instruction Manual - Page 36
English Basic Operations of remote Cassette player features • 4/¢ buttons Press the 4 button to . • DNPP/SBF button (for disc changers) Enters and cancels the Disc Name Preset Play mode. CD/External disc control features • Number/letter entry buttons Used to specify the track (disc) number used - Kenwood 6020 | Instruction Manual - Page 37
a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected wires or terminals touch metal on the car or anything else conducting electricity. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect - Kenwood 6020 | Instruction Manual - Page 38
Front right output (Red) KENWOOD disc changer control input NOTE To connect the Disc changer, consult your Disc changer manual. Rear right output ( you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a - Kenwood 6020 | Instruction Manual - Page 39
, place this unit in a hirizontal position and perform a loading/eject of the CD. ■ Installation Install onto the car bracket using the supplied screws (M5 × 6 mm, M5 x 7 mm). The holes of the car bracket to use will differ depending on the car model. Accessory2 (M4 × 8 mm) When a ground wire is - Kenwood 6020 | Instruction Manual - Page 40
installation types to fit your car. Perform "Assembly" before installation car. NOTE The illustration shows an example of installation using a vehicle bracket. The shape of the bracket varies with the vehicle to be installed. Some bracket requires three screws (Accessory1) on each side. DPX-6020 - Kenwood 6020 | Instruction Manual - Page 41
to be fixed either to the center or bottom, depending on the car model. Accessory0 (M5 × 7 mm) DPX-6020 2 Remove the factory-installed car stereo and install the unit. Factory-installed car stereo DPX-6020 Accessory8 Accessory9 (M3 × 6 mm) Accessory! (M5 × 10 mm) ■ Installation type 3 1 Attach - Kenwood 6020 | Instruction Manual - Page 42
English Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM The power does not turn on. No sound can be heard, or the volume is low. - Kenwood 6020 | Instruction Manual - Page 43
PROBLEM The memory is erased when the ignition is turned off. A CD ejects as soon as it is loaded. The sound skips on a CD. A track will not play. The DSP effects are imperceptible. POSSIBLE CAUSE The battery wire has not been connected to the proper terminal. The ignition and - Kenwood 6020 | Instruction Manual - Page 44
Troubleshooting Guide External Disc Control Mode PROBLEM POSSIBLE CAUSE The disc control mode cannot be selected. The specified disc does not play, but another one plays instead. No wire has been connected to the disc changer input terminal on the unit. The specified CD is quite dirty. The CD - Kenwood 6020 | Instruction Manual - Page 45
code does not disappear, consult your nearest service CD has no texts. The MD you tried playing is designed for use with data. ] Eject the MD designed for data and load the one designed for music. The tape player is malfunctioning. ] Eject the tape and try inserting it again. Contact the Kenwood - Kenwood 6020 | Instruction Manual - Page 46
70 dB Selectivity (±400 kHz 80 dB Stereo separation (1 kHz 40 dB AM tuner (S/N = 20dB 28 dBµ (25 µV) Cassette player section Tape speed 4.76 cm/sec. Wow 60 dB (Dolby B NR ON 68 dB CD player section Laser diode GaAlAs (λ=780 nm) Digital × 4 Preout level / Load 1500 mV/10 kΩ Preout
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
 |
 |
DPX-6020
© PRINTED IN JAPAN
B64-2050-00 (K) (+)
02/ 6 5 4 3 2 1
01/12 11 10 9 8 7 6 5
DOUBLE DIN SIZED CD/CASSETTE RECEIVER
INSTRUCTION MANUAL
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain
the best performance from your new double din sized CD/cassette receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated
on the warranty card, and in the space provided
below. Refer to the model and
serial numbers whenever you call upon your KENWOOD dealer for information or
service on the product.
Model
DPX-6020
Serial number