Kenwood KAC-X811D Instruction Manual
Kenwood KAC-X811D Manual
 |
View all Kenwood KAC-X811D manuals
Add to My Manuals
Save this manual to your list of manuals |
Kenwood KAC-X811D manual content summary:
- Kenwood KAC-X811D | Instruction Manual - Page 1
KAC-X811D KAC-PS811D SUBWOOFER POWER AMPLIFIER 7 page 2-9 INSTRUCTION MANUAL © B64-2794-00/00 (MV) - Kenwood KAC-X811D | Instruction Manual - Page 2
short circuit when replacing a fuse, first disconnect the wiring harness. Available Control Units: A KENWOOD's LX-Bus supporting Center Unit released in 2004 or later can control this unit. The operations of the (LX) AMP Control are explained in the Operation Manual of the Center Unit. NOTE • The LX - Kenwood KAC-X811D | Instruction Manual - Page 3
to applications, read the instruction manual well to select the The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where people, opposite side such as a gasoline tank, brake pipe, or wiring harness, and be careful not to cause scratches or other - Kenwood KAC-X811D | Instruction Manual - Page 4
KENWOOD disc changer/ External optional accessory Power control wire Control cable (option) �� �� �� Master amplifier Extension wire this limit, you cannot control amps from the Center Unit. • If you assign the same ID number to multiple amplifiers, they malfunction when you operate - Kenwood KAC-X811D | Instruction Manual - Page 5
of 1 ohm, connect � speakers with 1-ohm or higher amplifiers. 0 RESET button Resets the microprocessor of the unit. NOTE The values you have set with the Amplifier Control are NOT reset instruction manual of the center unit. ��� ��� % AMP CONT (amplifier - Kenwood KAC-X811D | Instruction Manual - Page 6
and you can register the values you have set with the Amplifier Control. To call the Amplifier Control's values, hold down the [2] button 3 or more seconds during ID number display ("AMP"). Then, you can recall the value when message "LOAD" is displayed. Default Resets all values you have set to the - Kenwood KAC-X811D | Instruction Manual - Page 7
the sound by controlling amplifiers from the Center Unit. 1 Enter AMP Control mode Select the AMP Control mode by following the 'AMP Control' procedure given on the Operation Manual of the Center Unit. NOTE Use the set item and value operation buttons by following the instructions given on the - Kenwood KAC-X811D | Instruction Manual - Page 8
wrong + /-polarity. • A speaker wire is pinched by a screw in the car body. • The switches may be set improperly. The sound does not change • The AMP CONT has been turned "OFF". even when you have changed it with the Amplifier Control. The set value cannot be • The AMP Control of the Center - Kenwood KAC-X811D | Instruction Manual - Page 9
Specifications Specifications subject to change without notice. Audio Section...KAC-X811D RMS Power Output (+B = 14.4 V, CEA-2006) (4 Ω) (1.0 % THD+N) ...533 W rated output) (MIN.) ...5.0 V Input Impedance ...10 kΩ Amplifier Control Section (EQ KAC-X811D/PS811D Bass frequency ...60 / 80 / 100 / 200 - Kenwood KAC-X811D | Instruction Manual - Page 10
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
KAC-X811D
KAC-PS811D
SUBWOOFER POWER AMPLIFIER
7
page 2-9
INSTRUCTION MANUAL
© B64-2794-00/00 (MV)