Kenwood KVT-536DVDM User Manual

Kenwood KVT-536DVDM Manual

Get Kenwood KVT-536DVDM PDF manuals and user guides View all Kenwood KVT-536DVDM manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood KVT-536DVDM manual content summary:

  • Kenwood KVT-536DVDM | User Manual - Page 1
    MONITOR WITH DVD RECEIVER KVT-536DVD KVT-536DVDM INSTALLATION MANUAL © B54-4752-00/00 (MW/M2W)
  • Kenwood KVT-536DVDM | User Manual - Page 2
    Accessories 1 2 3 4 5 6 ..........1 ..........1 ..........2 ..........1 ..........4 ..........4 2 | KVT-536DVD/KVT-536DVDM
  • Kenwood KVT-536DVDM | User Manual - Page 3
    Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order:
  • Kenwood KVT-536DVDM | User Manual - Page 4
    to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for
  • Kenwood KVT-536DVDM | User Manual - Page 5
    Cooling fan Antenna Cord REVERSE ILLUMI REMOTE CONT STEERING WHEEL REMOTE INPUT MUTE ANT CONT P. CONT Wiring harness (Accessory 1) Wiring harness (Accessory 2) FM/AM antenna input AV IN REAR VIEW CAMERA AV OUT Audio/Visual input / Rear View Camera Input • Visual input (Yellow) • Audio left
  • Kenwood KVT-536DVDM | User Manual - Page 6
    Optional Accessory Connection iPod AUDIO IN iPod (commercially available) KCA-iP301V (Optional Accessory) Audio Input Resistance-free stereo type mini plug (3.5Ф) Audio Output (Black) Visual Output (Yellow) USB terminal Visual Input (Yellow) Resistance-free mini plug (3.5Ф) USB terminal To KCA-
  • Kenwood KVT-536DVDM | User Manual - Page 7
    Installation/Removing the Unit Installation Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). English | 7
  • Kenwood KVT-536DVDM | User Manual - Page 8
    Installation/Removing the Unit Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 3 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Escutcheon (Accessory 4) Removal Tool (Accessory 3) Removing the Unit
  • Kenwood KVT-536DVDM | User Manual - Page 9
    Installing in Japanese-made Cars Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by "●" or Accessory 5 (M5x6mm) or Accessory 6 (M5x7mm) Car Bracket Accessory 5 (M5x6mm) or Accessory 6 (M5x7mm) Screws (included in audio unit package) Audio unit or others Screws (
  • Kenwood KVT-536DVDM | User Manual - Page 10
    Installing in Japanese-made Cars Installation on Toyota Car using Brackets at Holes shown by "●" or When using the bracket shown above, you cannot use screws at two holes of the right and left unit sides. 1. Mount the bracket at each side. Accessory 5 (M5x6mm) Car Bracket Screws (included in
  • Kenwood KVT-536DVDM | User Manual - Page 11
  • Kenwood KVT-536DVDM | User Manual - Page 12
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
©
B54-4752-00/00 (MW/M2W)
MONITOR WITH DVD RECEIVER
KVT-536DVD
KVT-536DVDM
INSTALLATION MANUAL