Kenwood LSF-1010 User Manual

Kenwood LSF-1010 Manual

Get Kenwood LSF-1010 PDF manuals and user guides View all Kenwood LSF-1010 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood LSF-1010 manual content summary:

  • Kenwood LSF-1010 | User Manual - Page 1
    LSF-1010 SPEAKER SYSTEM INSTRUCTION MANUAL KENWOOD CORPORATION B61-1040-00 EN
  • Kenwood LSF-1010 | User Manual - Page 2
    are designed for operation as follows. Europe and U.K AC 230 V only Safety precautions LSF-1010 (EN) Caution : Read this section carefully to ensure safe operation. WARNING : TO PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
  • Kenwood LSF-1010 | User Manual - Page 3
    manual handy for future reference. LSF-1010 System Components ÷ One subwoofer ÷ Two satellite speakers and stands KENWOOD (SW-1010) Accessories ÷ Pin-plug audio cable ÷ Two speaker cords Contents Introduction 3 LSF-1010 Speakers 18 Maintenance 23 Troubleshooting 24 Specifications 25
  • Kenwood LSF-1010 | User Manual - Page 4
    LSF-1010 (EN) Caution : Read this page carefully to ensure safe operation. FRANÇAIS DEUTSCH Please read all of the safety and operating instructions before operating this appliance. Adhere to all warnings on the appliance and in the instruction manual service center. NEDERLANDS ITALIANO ESPAÑOL
  • Kenwood LSF-1010 | User Manual - Page 5
    LSF-1010 (EN) Caution : Read this page carefully to ensure safe operation. FRANÇAIS DEUTSCH 13. Damage requiring service - The appliance should be serviced by qualified service by following the instruction manual. Adjust only those controls that are covered by the instruction manual as an improper
  • Kenwood LSF-1010 | User Manual - Page 6
    each speaker to a stand as described below. Subwoofer LSF-1010 (EN) The subwoofer can be positioned either vertically or horizontally. For detail, see page 8 "Setting Up the Satellite Speakers" KENWOOD Vertical Orientation Horizontal Orientation KENWOOD CAUTION Be sure to unplug the speaker
  • Kenwood LSF-1010 | User Manual - Page 7
    noise in your AM reception, you can correct the problem by moving the subwoofer farther from the receiver. • (and subwoofer wires). Separate AM Antenna KENWOOD CAUTION (SUBWOOFER only) To ensure adequate : 10 cm 7 Location and Orientation LSF-1010 (EN) Subwoofer and Satellite Speaker Magnetic
  • Kenwood LSF-1010 | User Manual - Page 8
    of the corresponding screw, and then tighten the screw. White stripe Set the cord into cord cramp. 1. Attach the speaker to the arm. LSF-1010 (EN) Use the speaker screw and washer removed from the satellite speaker to make the attachment. Satellite speaker Washer Screw 1 Remove the screw and
  • Kenwood LSF-1010 | User Manual - Page 9
    2. Attach the arm to the stand. Setting Up the Satellite Speakers 9 LSF-1010 (EN) Push the clip open (see illustration) and fit onto the pole. You can adjust the position of the speaker by changing the height and
  • Kenwood LSF-1010 | User Manual - Page 10
    possible to connect to standard PRE-OUT jacks on your amp or receiver. For instructions, see page 13, "Connecting to Amp's Standard PREOUT Jacks." • It see page 13, "Connecting to Amp's Standard PRE-OUT Jacks." Subwoofer LSF-1010 (EN) To electrical outlet (wall outlet) 1 LINE IN jacks Connect to
  • Kenwood LSF-1010 | User Manual - Page 11
    . SUBWOOFER PRE-OUT jack (on amp or receiver) SPEAKERS R L SUPER WOOFER PRE OUT Pin-plug audio cable (included) Making Connections 11 LSF-1010 (EN) CAUTION Do not plug in the power cord until you have finished making all connections. Subwoofer · ª Speaker cord (included) · ª Included
  • Kenwood LSF-1010 | User Manual - Page 12
    FRANÇAIS 12 Connecting to Amp's Speaker Output Terminals Making Connections LSF-1010 (EN) Connect the FROM AMPLIFIER terminals on the subwoofer to the speaker output terminals on your amplifier or receiver. Connect the TO SPEAKERS terminals on
  • Kenwood LSF-1010 | User Manual - Page 13
    the subwoofer.) Pin-plug audio cable (purchased separately) Making Connections 13 LSF-1010 (EN) CAUTION Do not plug in the power cord until you have affect the volume from the subwoofer. This means that you will need to manually adjust the subwoofer volume each time you adjust the volume at the amp
  • Kenwood LSF-1010 | User Manual - Page 14
    4 PHASE switch 5 TURNOVER FREQUENCY adjuster dial Adjusting the Sound LSF-1010 (EN) The VOLUME, TURNOVER FREQUENCY, and PHASE controls allow Normal Reverse Try switching the phase if you encounter either of the following problems. • If the interaction of subwoofer and speak- ers is producing
  • Kenwood LSF-1010 | User Manual - Page 15
    when making major changes to the sound input (for example, when first switching on the amplifier or when first dropping the needle onto a record). 15 LSF-1010 (EN) ESPAÑOL ITALIANO NEDERLANDS DEUTSCH FRANÇAIS
  • Kenwood LSF-1010 | User Manual - Page 16
    Satellite Speaker Position You can adjust the position of the speaker by changing the height and angle of the arm. 2. Loosen the two screws. Screw LSF-1010 (EN) Use a coin to turn each screw. • Once you have loosened both screws you will be able to move the arm up and down, or
  • Kenwood LSF-1010 | User Manual - Page 17
    two arm screws further to remove them from the arm holders. 17 Adjusting the Satellite Speaker Position 2. Set the arm holders to the desired angle. LSF-1010 (EN) At time of shipping, the arm is mounted at angle D. 1 Take one of the arm holders, rotate it any of the angles A to E indicated
  • Kenwood LSF-1010 | User Manual - Page 18
    Sideways on the stand ("Offset mount") • On the wall ("Wall mount") • Without the stand ("Clip-on mount") 2. Set the arm holder to vertical position. LSF-1010 (EN) 1 Position the arm holder that you just removed so that the hole in the holder is vertical (facing directly up/down), and set it
  • Kenwood LSF-1010 | User Manual - Page 19
    the wall you are using is strong enough to support the full weight of the speaker and stand (approx given here when carrying out installation. Kenwood can assume no liability for injury or Speakers 2. Set the arm holders to the desired angle. LSF-1010 (EN) 1 Take one of the arm holders, rotate
  • Kenwood LSF-1010 | User Manual - Page 20
    speaker cord can pass. Please do not neglect to attach the cushions. Other Ways to Set Up the Satellite Speakers 5. Attach and fasten the arm. LSF-1010 (EN) 1 Fit the arm through the holes in the arm holders, adjust it to the desire height, and then tighten the arm screws. 2 Place the
  • Kenwood LSF-1010 | User Manual - Page 21
    ). Other Ways to Set Up the Satellite Speakers 21 LSF-1010 (EN) For information about how to remove/replace the the arm holders to the appropriate angle. For instructions, see page 17, "Adjusting the Arm Angle." position. Many objects are not suitable as supports - either because the material is not
  • Kenwood LSF-1010 | User Manual - Page 22
    the speaker directly to an amp; the connection must be relayed through the base. Extension speaker cord Other Ways to Set Up the Satellite Speakers LSF-1010 (EN)
  • Kenwood LSF-1010 | User Manual - Page 23
    connections, as these may cause the subwoofer to fail. Agents that include oil may in addition lead to deformation of the plastic. 23 LSF-1010 (EN) Removing and Reattaching the Screen Use the following proceeding to remove or reattach the subwoofer's front screen. 1. To remove the screen: ΠGently
  • Kenwood LSF-1010 | User Manual - Page 24
    24 Troubleshooting If the subwoofer does not seem to be working correctly, the following advice may help you correct the problem. LSF-1010 (EN) FRANÇAIS Problem No sound. Possible Cause Correction * Wires are not securely connected. * The volume is turned all the way down. * The amp or
  • Kenwood LSF-1010 | User Manual - Page 25
    setting up of the satellite speakers. *2: Stand included. 25 LSF-1010 (EN) Subwoofer System Subwoofer system with built-in amplifier (Magnetically Weight 4.4 kg (9.7 lb) DEUTSCH NEDERLANDS ITALIANO ESPAÑOL 1.KENWOOD follows a policy of continuous advancements in development. For this
  • Kenwood LSF-1010 | User Manual - Page 26
    warranty card, and in the space provided at right. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product. Model Serial Number
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
LSF-1010
SPEAKER SYSTEM
INSTRUCTION MANUAL
KENWOOD CORPORATION
B61-1040-00
EN