Kenwood NX-1300N User Manual 4

Kenwood NX-1300N Manual

Get Kenwood NX-1300N PDF manuals and user guides View all Kenwood NX-1300N manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood NX-1300N manual content summary:

  • Kenwood NX-1300N | User Manual 4 - Page 1
    NX-1000 series USER MANUAL B5A-3233-00/01_XMC_EN
  • Kenwood NX-1300N | User Manual 4 - Page 2
    CONTENTS MODELS COVERED BY THIS MANUAL 5 PREPARATION 6 INSTALLING/ REMOVING THE BATTERY PACK 6 INSTALLING THE ANTENNA 7 INSTALLING THE BELT CLIP 7 INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS....... 8 INSTALLING THE SPEAKER/ MICROPHONE
  • Kenwood NX-1300N | User Manual 4 - Page 3
    SCAN...67 TEMPORARY CHANNEL LOCKOUT 67 PRIORITY SCAN 67 SCAN REVERT 68 DTMF (DUAL TONE MULTI FREQUENCY) CALLS 69 MAKING A DTMF CALL 69 Manual Dialing 69 Keypad Auto PTT 69 Store & Send 69 Stun Code 69 EMERGENCY CALLS 70 SCRAMBLER (ANALOG)/ ENCRYPTION (NXDN/ DMR 71 SECURE (ENCRYPTED)
  • Kenwood NX-1300N | User Manual 4 - Page 4
    Transmitting 76 Receiving...76 SHORT MESSAGES 77 GPS REPORT 77 5-TONE SIGNALING (X2/ M/ M3 types 78 SELCALL (SELECTIVE CALLING 78 Transmitting 78 Receiving...78 STATUS MESSAGE 79 Transmitting 79 Receiving...79 VOICE OPERATED TRANSMISSION (VOX 80 VOX Type...80 VOX Operation 80 Semi-VOX
  • Kenwood NX-1300N | User Manual 4 - Page 5
    MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual: NXDN/ Analog Transceiver NX-1200N (VHF TRANSCEIVER) NX-1300N (UHF TRANSCEIVER) DMR/ Analog Transceiver NX-1200D (VHF TRANSCEIVER) NX-1300D (UHF TRANSCEIVER) Analog Transceiver NX-
  • Kenwood NX-1300N | User Manual 4 - Page 6
    PREPARATION INSTALLING/ REMOVING THE BATTERY PACK The battery pack is not charged at the factory; charge it before use. 1 Align the battery pack with the back of the transceiver, then press the battery pack and transceiver firmly together until the release latch on the base of the transceiver locks.
  • Kenwood NX-1300N | User Manual 4 - Page 7
    INSTALLING THE ANTENNA Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. Antenna INSTALLING THE BELT CLIP If necessary, attach the belt clip using the two supplied M3 x 8 mm binding screws. Note: ◆ If the
  • Kenwood NX-1300N | User Manual 4 - Page 8
    INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS Note: ◆ For the speaker/ microphone jack, waterproof performance is guaranteed by securing the supplied cap. Waterproof performance will not be guaranteed by connecting an optional speaker/ microphone, etc. ◆ Use the Phillips #1 screwdriver. 1 If
  • Kenwood NX-1300N | User Manual 4 - Page 9
    Buttons and Controls Antenna ORIENTATION a Speaker f Microphone g Display h d Battery pack Keypad e bc Full Button Model Standard Button Model Basic Button Model a Selector Rotate to change the operating channel or zone. b Status indicator Lights during a specified mode, based on dealer
  • Kenwood NX-1300N | User Manual 4 - Page 10
    Display Indicator Description Displays the signal strength. The Monitor or Squelch Off function is activated. Blinks when an incoming call matches your Optional Signaling. The Talk Around function is activated. Scan, Priority Scan, or Voting/ Site Roaming is in progress. Blinks when the scan
  • Kenwood NX-1300N | User Manual 4 - Page 11
    BASIC OPERATIONS SWITCHING POWER ON/ OFF Turn the Power switch/ Volume control clockwise to switch the transceiver power ON. • The Power on text appears if the Power on text has been set. Turn the Power switch/ Volume control counterclockwise to switch the transceiver power OFF. ADJUSTING THE VOLUME
  • Kenwood NX-1300N | User Manual 4 - Page 12
    TRANSMITTING 1 Select the desired zone and channel. 2 Press the button programmed as [Monitor] or [Squelch Off] to check whether or not the channel is free. • If the channel is busy, wait until it becomes free. 3 Press the PTT switch and speak to the microphone. Release the PTT switch to receive. •
  • Kenwood NX-1300N | User Manual 4 - Page 13
    Making Individual Calls (NXDN/ DMR) You can select a Unit ID/ name from the list to make a call to those parties on a channel. 1 Press the button programmed as [Individual], [Individual + Short Message] or [Individual + Status] to enter Individual Call Mode. • Alternatively, press the button
  • Kenwood NX-1300N | User Manual 4 - Page 14
    Receiving Group Calls (NXDN/ DMR) When you receive a group call on a channel and the received group ID matches the ID set up on your transceiver, you can hear the caller's voice. Receiving Individual Calls (NXDN/ DMR) When you receive an individual call on a channel, a ringing tone will sound and
  • Kenwood NX-1300N | User Manual 4 - Page 15
    ACCESSIBLE FUNCTIONS FUNCTION MODE Your transceiver operations vary according to the functions that your dealer has programmed to the transceiver buttons and Selector. Refer to "FUNCTIONS LIST" {p. 17} for the available programmable functions. MENU MODE (LCD Model) Many functions on this
  • Kenwood NX-1300N | User Manual 4 - Page 16
    3 Press the [ S ] button to view the function list for the selected category. 4 Press [ ] to select a function item. • Press the [ A ] button to return to the category list. 5 Press the [ S ] button. The selected function functions. • Options for a function, such as Microphone type,
  • Kenwood NX-1300N | User Manual 4 - Page 17
    FUNCTIONS LIST PF Button : Functions that can be programmed to the transceiver buttons Menu : Functions that can be accessed using the transceiver Menu Non-LCD : Non-LCD Model Analog : Channels set up for Analog NXDN : Channels set up for NXDN DMR : Channels set up for DMR ✔ : Available N/A : Not
  • Kenwood NX-1300N | User Manual 4 - Page 18
    Function Channel Up (Continuous) Menu Display - PF Button Menu ✔ N/A Clear - ✔ N/A CW Message - ✔ N/A Digit 1x Down *3 - ✔ N/A Digit 1x Up *3 - ✔ N/A Digit 10x Down *3 - ✔ N/A Digit 10x Up *3 - ✔ N/A Direct Channel 1 ~ 5 - ✔ N/A Direct Channel 1 DR 1 SEL ~ ~ 5 Select DR 5
  • Kenwood NX-1300N | User Manual 4 - Page 19
    + Short Message IND SDM ✔ ✔ Individual + Status IND STAT ✔ ✔ Lone Worker L-WK ✔ ✔ Low Transmit Power LOW PWR ✔ ✔ Maintenance MAINT ✔ ✔ Manual Site Hunt M SITE H ✔ ✔ Medium Transmit Power MED PWR N/A ✔ Menu - ✔ N/A Microphone Sense MIC SENS N/A ✔ Microphone Type MIC TYPE
  • Kenwood NX-1300N | User Manual 4 - Page 20
    Function RX Auto Gain Control Save Log Data Scan Scan Delete/Add Scrambler/ Encryption Scrambler/ Encryption Code Send the GPS Data Short Message Speaker Attenuation Speaker Type Squelch Level Squelch Off Squelch Off Momentary Stack Status Surveillance Talk Around Transceiver Password TX Audio
  • Kenwood NX-1300N | User Manual 4 - Page 21
    Function VOX Function Menu Display VOX PF Button Menu ✔ ✔ NonLCD ✔ Analog NXDN DMR ✔ ✔✔ Zone Delete/Add ZONE D/A ✔ ✔ ✔ ✔ ✔✔ Zone Down - ✔ N/A ✔ ✔ ✔✔ Zone Down (Continuous) - ✔ N/A ✔ ✔ ✔✔ Zone Select *4 - N/A N/A ✔ ✔ ✔✔ Zone Up/Down *5 N/A N/A N/A ✔ ✔✔ Zone Up - ✔
  • Kenwood NX-1300N | User Manual 4 - Page 22
    FUNCTIONS OVERVIEW Following is a brief overview of the functions available on the transceiver accessible using the Menu and/or programmable to the transceiver buttons. • For details on functions that are not included in "FUNCTIONS OVERVIEW" and "FUNCTION DESCRIPTIONS" {p. 65}, please consult your
  • Kenwood NX-1300N | User Manual 4 - Page 23
    Battery Status [Analog/ NXDN/ DMR] Allows you to check the battery power status. PF Button: Press the programmed button, the Battery Status function operates. Menu Mode: Select "BAT STAT" and press the [ S ] button, the Battery Status function operates. Battery status is represented by the number
  • Kenwood NX-1300N | User Manual 4 - Page 24
    Button Lock [Analog/ NXDN/ DMR] Locking the transceiver button operation. This function prevents the incorrect operation of the transceiver by physical contact while carrying the transceiver, such as around the waist. PF Button: Press the programmed button to lock the transceiver buttons. • Beep A
  • Kenwood NX-1300N | User Manual 4 - Page 25
    Call Interruption [DMR] Allows a transceiver other than the transmitting transceiver to terminate voice communications by sending a Call Interruption request message. If a transceiver receives a Call Interruption request message on the channel where the transceiver is performing voice communications
  • Kenwood NX-1300N | User Manual 4 - Page 26
    Channel Entry [Analog/ NXDN/ DMR] In Channel Entry Mode, channel can be selected by the same operation as List selection. PF Button: 1 Press the programmed button to enter Channel Entry Mode. 2 Press the [ ] buttons to select your desired channel. 3 Press the [ S ] button to confirm
  • Kenwood NX-1300N | User Manual 4 - Page 27
    To enter 3-digit channel number (example: Channel 123): 1 Press the programmed button to enter Channel Entry Mode. 2 Press the [ ] buttons to select "1". 3 Press the [ S ] button. 4 Press the [ ] buttons to select "2". 5 Press the [ S ] button. 6 Press the [
  • Kenwood NX-1300N | User Manual 4 - Page 28
    Channel Select [Analog/ NXDN/ DMR] Selector: Turn the Selector to select the channel number. Channel Up/Down Selector: Turn the Selector to increase/ decrease the channel number. Channel Up/ Channel Down [Analog/ NXDN/ DMR] PF Button: Press the programmed button to increase/ decrease the channel
  • Kenwood NX-1300N | User Manual 4 - Page 29
    Digit 1x Up/ Digit 1x Down [Analog] In 5-tone to increment/ decrement the 5-tone selcall code by 1. PF Button: Press the programmed button to increase/ decrease the 5-tone selcall code by 1 with each press. 1st digit code from the right of 5-tone selcall code Digit 10x Up/ Digit 10x Down [Analog] In
  • Kenwood NX-1300N | User Manual 4 - Page 30
    Direct Channel 1 ~ 5 Select [Analog/ NXDN/ DMR] Allows you to set the currently selected channel as the Direct Channel 1 ~ 5. 1 Select the channel to be set as Direct Channel. 2 PF Button: Press and hold the programmed button to set the currently selected channel as Direct Channel 1 ~ 5. • Beep C (3
  • Kenwood NX-1300N | User Manual 4 - Page 31
    Emergency [Analog/ NXDN/ DMR] This is for entering Emergency Mode if the transceiver is in standby mode. If the transceiver is in Emergency mode, it exits the emergency mode. In Emergency Mode, the transceiver repeats transmission and reception at regular intervals. PF Button: Press and hold the
  • Kenwood NX-1300N | User Manual 4 - Page 32
    External Speaker [Analog/ NXDN/ DMR] If external speaker connected to the transceiver, select the output of the speaker to the external speaker or internal speaker. PF Button: Press the programmed button to switch the external speaker or internal speaker. Menu Mode: 1 Select "SPEAKER" and press the
  • Kenwood NX-1300N | User Manual 4 - Page 33
    Function [Analog/ NXDN/ DMR] Allows you to access the 2nd function programmed to a button. Programmable buttons can be assigned Main function and 2nd function. PF Button: 1 Press the programmed button to enter 2nd function input wait state. • Beep A (1 beep) sounds. • "FNC" is displayed. 2 Press the
  • Kenwood NX-1300N | User Manual 4 - Page 34
    Group + Short Message [Analog/ NXDN/ DMR] Allows you to specify a Group ID to send short messages. 1 PF Button: Press the programmed button to enter Group Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone). Menu Mode: Select "GRP SDM" and press the [ S ] button to enter Group Call
  • Kenwood NX-1300N | User Manual 4 - Page 35
    High Transmit Power [Analog/ NXDN/ DMR] Turns High Transmit Power On or Off. When using a channel programmed with low or medium power, this allows you to change the output power to high. PF Button: Press the programmed button to change the output power to high. • Beep A (1 beep) sounds. Press this
  • Kenwood NX-1300N | User Manual 4 - Page 36
    Home Channel Select [Analog/ NXDN/ DMR] Allows you to set the currently selected channel to Home Channel. 1 Select the channel to be set as Home Channel. 2 PF Button: Press and hold the programmed button to set the currently selected channel as the Home Channel. • Beep C (3 beeps) sounds. Menu Mode:
  • Kenwood NX-1300N | User Manual 4 - Page 37
    Individual + Short Message [Analog/ NXDN/ DMR] Allows you to specify a Unit ID to send short messages. 1 PF Button: Press the programmed button to enter Individual Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone). Menu Mode: Select "IND SDM" and press the [ S ] button to enter
  • Kenwood NX-1300N | User Manual 4 - Page 38
    Lone Worker [Analog/ NXDN/ DMR] Using Lone Worker function, the transceiver can automatically enter Emergency Mode and notify the base station of the emergency status when the transceiver becomes disabled from operating due to an accident. PF Button: Press the programmed button to change the Lone
  • Kenwood NX-1300N | User Manual 4 - Page 39
    Low Transmit Power [Analog/ NXDN/ DMR] Turns Low Transmit Power On or Off. When using a channel programmed with medium or high power, this allows you to change the output power to low. PF Button: Press the programmed button to change the output power to Low. • Beep A (1 beep) sounds. Press this
  • Kenwood NX-1300N | User Manual 4 - Page 40
    Maintenance [Analog/ NXDN/ DMR] Allows you to display the signal strength and Bit Error Rate (BER) on the LCD when constructing the system or during maintenance. 1 PF Button: Press the programmed button to enter Maintenance Display Mode. Menu Mode: Select "MAINT" and press the [ S ] button to enter
  • Kenwood NX-1300N | User Manual 4 - Page 41
    the same System set in DMR Site Roaming and go to search for repeaters that can detect the synchronization signal. • "SEARCH" is displayed during Manual Site Hunt operation. Medium Transmit Power [Analog/ NXDN/ DMR] Turns Medium Transmit Power On or Off. When using a channel programmed with low or
  • Kenwood NX-1300N | User Manual 4 - Page 42
    Microphone Sense [Analog/ NXDN/ DMR] Allows you to change the internal microphone sensitivity. Menu Mode: 1 Select "MIC SENS" and press the [ S ] button. 2 Press the [ ] buttons to select the microphone sensitivity. • You can select from +6 dB (High sensitivity) to -20 dB (Low
  • Kenwood NX-1300N | User Manual 4 - Page 43
    -OH*, KHS-10D-BH, KHS-10D-OH MIC 7 EMC-11, EMC-12 MIC 8 KHS-1* MIC 9 KHS-29F MIC 10 KEP-2 MIC 11 KHS-8NC * : Not support for DMR. 43
  • Kenwood NX-1300N | User Manual 4 - Page 44
    Monitor [Analog/ NXDN/ DMR] Allows you to turn the transceiver signaling off, to listen to all calls that are received on the channel. PF Button: Press the programmed button to change the Monitor On. • Beep A (1 beep) sounds. Press this button again to change the Monitor Off. • Beep B (2 beeps)
  • Kenwood NX-1300N | User Manual 4 - Page 45
    OST List [Analog] Allows you to enter OST List mode. 1 PF Button: Press and hold the programmed button to enter OST List Mode. Menu Mode: Select "OST LIST" and press the [ S ] button to enter OST List Mode. 2 Press the [ ] buttons to select the OST List. 3 Press the [ S ] button to
  • Kenwood NX-1300N | User Manual 4 - Page 46
    Priority-channel Select [Analog/ NXDN/ DMR] A Priority channel must be programmed in order for Priority Scan to function. When using a single Priority channel, the transceiver will automatically change to the Priority channel when a call is received on it, even if a call is being received on a
  • Kenwood NX-1300N | User Manual 4 - Page 47
    Radio Check (MDC-1200) [Analog] This function is for MDC-1200 Radio Check. Radio Check is a function for checking whether a transceiver is available for calling, such as whether the transceiver is on or whether it is within the reach of radio waves. Menu Mode: 1 Select "RD CHK" and press the [ S ]
  • Kenwood NX-1300N | User Manual 4 - Page 48
    Radio Uninhibit (MDC-1200) [Analog] This is for MDC-1200 Radio Uninhibit. Radio Uninhibit is a function for reviving a transceiver which has been stunned. Menu Mode: 1 Select "UNINHIB" and press the [ S ] button to enter Radio Uninhibit Mode. 2 Press the [ ] buttons to select the
  • Kenwood NX-1300N | User Manual 4 - Page 49
    Remote Control [NXDN/ DMR] Allows you to remotely control a specified transceiver from the transceiver. In the NXDN and DMR systems, it allows you to operate the transceiver directly, send a remote control message and control the target transceiver. Note: ◆ The Remote Control is a software option.
  • Kenwood NX-1300N | User Manual 4 - Page 50
    Menu Mode: 1 Select "RMT CTRL" and press the [ S ] button to enter Remote Control Mode. 2 Press the [ ] buttons to select Unit ID List. 3 Press the [ S ] button to enter Remote Control Message Selection. 4 Press the [ ] buttons to select Remote Control Message. 5 Press
  • Kenwood NX-1300N | User Manual 4 - Page 51
    mode. Save Log Data [Analog/ NXDN/ DMR] This function saves the operation and communication logs of this transceiver. • This function is for field support use such for your dealer. Scan [Analog/ NXDN/ DMR] Allows you starting or stopping scan. PF Button: Press the programmed button to start scanning
  • Kenwood NX-1300N | User Manual 4 - Page 52
    Scan Delete/Add [Analog/ NXDN/ DMR] Allows you to include or omit each channel in the scan sequence. 1 Select your desired channel. 2 PF Button: Press the programmed button to change the Scan Delete/Add status of the channel. Menu Mode: Select "SCN D/A" and press the [ S ] button to activate/
  • Kenwood NX-1300N | User Manual 4 - Page 53
    Scrambler/Encryption Code [Analog/ NXDN/ DMR] Allows you to change the Scrambler Code/ Encryption Key used in the transmission. 1 PF Button: Press and hold the programmed button to enter Scrambler/ Encryption Code Mode. Menu Mode: Select "SCRENC C" and press the [ S ] button to enter Scrambler/
  • Kenwood NX-1300N | User Manual 4 - Page 54
    Send the GPS Data [Analog/ NXDN/ DMR] Allows you to send your positioning data to the base station when a GPS speaker/ microphone has been installed. • When the power is turned ON and/or the reception condition of the GPS satellite is poor, positioning may take longer to complete. PF Button: Press
  • Kenwood NX-1300N | User Manual 4 - Page 55
    , KHS-35F KHS-10-BH*, KHS-10-OH*, KHS-10D-BH, KHS-10D-OH EMC-11, EMC-12 KHS-1* KHS-29F KEP-2 KHS-8NC * : Not support for DMR. 55
  • Kenwood NX-1300N | User Manual 4 - Page 56
    Squelch Level [Analog] Allows you to adjust the transceiver squelch level. 1 PF Button: Press the programmed button to enter Squelch Level Adjustment Mode. Menu Mode: Select "SQL LVL" and press the [ S ] button to enter Squelch Level Adjustment Mode. 2 Press the [ ] buttons to increase
  • Kenwood NX-1300N | User Manual 4 - Page 57
    Stack [Analog/ NXDN/ DMR] Allows you to check the records of received calls and messages received. • The " " indicator lights up when all stacked data is already read. • When there is unread data, The " " indicator blinks. 1 PF Button: Press the programmed button to enter Stack Mode. Menu Mode:
  • Kenwood NX-1300N | User Manual 4 - Page 58
    3 Press the [ ] buttons to select the List. • Each time press the [ S ] button to change display type (Message → Caller ID → Channel No.→ Message→ ). • Press the [A] button, delete confirmation is displayed, press the [S] button to delete displayed Caller ID and Message. • Press and
  • Kenwood NX-1300N | User Manual 4 - Page 59
    Surveillance [Analog/ NXDN/ DMR] Allows you to disable the alert tone, backlight and LED functions. The Surveillance function is used when the change of the transceiver status needs to be kept unnoticed, such as while on a Public Safety operation. PF Button: Press the programmed button to activate
  • Kenwood NX-1300N | User Manual 4 - Page 60
    TX Audio Equalizer [NXDN/ DMR] Allows you to set the transmission audio characteristic (Flat, High boost, or Low boost). Menu Mode: 1 Select "TX EQ" and press the [ S ] button. 2 Press the [ ] buttons to select the audio characteristic. 3 Press the [ S ] button to confirm and exit
  • Kenwood NX-1300N | User Manual 4 - Page 61
    VOX [Analog/ NXDN/ DMR] Allows you to adjust the VOX Gain level. 1 PF Button: Press the programmed button to enter VOX Gain Level Adjustment Mode. Menu Mode: Select "VOX LVL" and press the [ S ] button to enter VOX Gain Level Adjustment Mode. 2 Press the [ ] buttons to increase and
  • Kenwood NX-1300N | User Manual 4 - Page 62
    Zone Delete/Add [Analog/ NXDN/ DMR] Allows you to include or omit each Zone in the Multi-Zone scan sequence. 1 Select your desired zone. 2 PF Button: Press the programmed button to switch the Zone Delete/Add status of the channel. Menu Mode: Select "ZONE D/A" and press the [ S ] button to switch the
  • Kenwood NX-1300N | User Manual 4 - Page 63
    Send is Disable, Keypad is entered with Autodial Mode (List Selection). • For Store and Send is Enable, pressing the [ 0 ] ~ [ 9 button is input with Autodial Mode (Manual input). 63
  • Kenwood NX-1300N | User Manual 4 - Page 64
    + Short Message Group Group + Status Group + Short Message This function allows you to send DTMF by pressing Keypad without PTT switch. • Set DTMF Manual Dialing is Enable to send the DTMF Code by pressing the [ 0 ] ~ [ 9 button. • By pressing the [ 0 ] ~ [ 9 button, send the DTMF Code of the
  • Kenwood NX-1300N | User Manual 4 - Page 65
    FUNCTION DESCRIPTIONS For details on functions that are not included in "FUNCTIONS OVERVIEW" {p. 22} and "FUNCTION DESCRIPTIONS", please consult your dealer. TRANSCEIVER PASSWORD LCD Model If the transceiver is password protected, "PASSWORD" will appear on the display when the power is turned on. To
  • Kenwood NX-1300N | User Manual 4 - Page 66
    Non-LCD Model If your transceiver is password protected, the LED will light blue when you turn the transceiver ON. Enter the password (up to 6 digits) using the following procedure. 1 Set the Selector to position "1". 2 Press the Side 1 or Side 2 button to enter the first digit. • The Side 1 button
  • Kenwood NX-1300N | User Manual 4 - Page 67
    SCAN Scan is useful for monitoring signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops on a channel if a signal is present. To begin scanning, press the button programmed as [Scan]. • The " " indicator appears on the display. • If
  • Kenwood NX-1300N | User Manual 4 - Page 68
    SCAN REVERT The Scan Revert channel is the channel selected when you press the PTT switch to transmit during scan. Your dealer can program one of the following Scan Revert channels: • Selected: The last channel selected is assigned as the new revert channel. • Selected + Talkback: If the channel has
  • Kenwood NX-1300N | User Manual 4 - Page 69
    Dialing and Keypad Auto PTT are available only on full button model. MAKING A DTMF CALL Manual Dialing 1 Press and hold the PTT switch. 2 Enter the desired digits using the keypad. • The corresponding DTMF tones sound each time you press a button. • If
  • Kenwood NX-1300N | User Manual 4 - Page 70
    EMERGENCY CALLS If your transceiver has been programmed with the Emergency function, you can make emergency calls. 1 Press and hold the button programmed as [Emergency]. • Depending on the delay time programmed into your transceiver, the length of time you must hold the Emergency button will vary. •
  • Kenwood NX-1300N | User Manual 4 - Page 71
    SCRAMBLER (ANALOG)/ ENCRYPTION (NXDN/ DMR) Note: ◆ The following types of encryption are available depending on the protocol used. NXDN : Bit scrambling (built-in encryption function) DMR : Bit scrambling (built-in encryption function) and Enhanced Encryption ◆ The Enhanced Encryption is a software
  • Kenwood NX-1300N | User Manual 4 - Page 72
    SELECTING THE ENCRYPTION KEY 1 Press the button programmed as [Scrambler/Encryption Code] to enter Scrambler/Encryption Code Mode. • Alternatively, press the button programmed as [Menu] to enter Scrambler/ Encryption Code Mode using the Menu Mode. 2 Select the new Encryption key using the [
  • Kenwood NX-1300N | User Manual 4 - Page 73
    SIGNALING QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) [ANALOG] Your dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/ code which allows you to ignore (not hear) calls from other parties who are using the same channel. When a channel
  • Kenwood NX-1300N | User Manual 4 - Page 74
    COLOR CODE (CC) [DMR] Color Code is a digital signaling for DMR protocol to enable smooth communication among groups using the same channel. OPTIONAL SIGNALING Your dealer may also program several types of optional signaling for your transceiver channels. 2-tone Signaling [Analog] 2-tone Signaling
  • Kenwood NX-1300N | User Manual 4 - Page 75
    FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function, and is a protocol owned by JVCKENWOOD Corporation. FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming. Note: ◆ This function is available
  • Kenwood NX-1300N | User Manual 4 - Page 76
    Identification Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number. Each transceiver has its own ID. • Enter a Fleet number (100 ~ 349) to make a fleet call. • Enter an ID number (1000 ~ 4999) to make an individual call in your fleet. • Enter a Group ID (which is
  • Kenwood NX-1300N | User Manual 4 - Page 77
    SHORT MESSAGES This transceiver can receive short data messages which contain a maximum of 48 characters. GPS REPORT GPS data can be manually transmitted by pressing the button programmed as [Send the GPS Data], or by accessing the Menu. If set up by your dealer, GPS data may
  • Kenwood NX-1300N | User Manual 4 - Page 78
    5-TONE SIGNALING (X2/ M/ M3 types) 5-tone Signaling is enabled or disabled by your dealer. This function opens the squelch only when the transceiver receives the 5 tones programmed in your transceiver. Transceivers that do not transmit the correct tones will not be heard. SELCALL (SELECTIVE CALLING)
  • Kenwood NX-1300N | User Manual 4 - Page 79
    STATUS MESSAGE You can send and receive Status messages which may be decided in your talk group. Messages can contain up to 8 alphanumeric characters. A maximum of 32 received messages can be stored in the stack memory of your transceiver. Transmitting 1 Select your desired zone and channel. 2 Press
  • Kenwood NX-1300N | User Manual 4 - Page 80
    VOICE OPERATED TRANSMISSION (VOX) VOX (VOX/ Semi-VOX) operation allows you to transmit hands-free. This feature can be activated or deactivated by your dealer. To operate VOX, you must use an optional headset. VOX Type VOX: When the voice level to the microphone is higher than the reference level (
  • Kenwood NX-1300N | User Manual 4 - Page 81
    Semi-VOX Operation 1 Connect a headset to the transceiver. • The VOX function does not activate when a headset is not connected to the accessory terminal of the transceiver. 2 Press the button programmed as [VOX Function]. • Alternatively, you can press the button programmed as [Menu] to enter VOX
  • Kenwood NX-1300N | User Manual 4 - Page 82
    BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer is used to prevent any caller from using a channel for an extended period of time. If you continuously transmit for a period of time that exceeds the programmed time, the transceiver will stop transmitting and an alert tone will sound. To
  • Kenwood NX-1300N | User Manual 4 - Page 83
    VOICE ANNOUNCEMENT An audio voice will be announced as below by dealer setting. • When changing the zone and/or channel, the new zone and channel number are announced. • When changing the function setting, the new setting is announced. - Scrambler/Encryption - VOX Function - Home Channel - Button
  • Kenwood NX-1300N | User Manual 4 - Page 84
    BUSY CHANNEL LOCKOUT (BCL) If BCL is set up by your dealer, you will be unable to transmit on the channel if it is already in use. Under these circumstances, use a different channel or wait until the channel becomes free. However, if BCL Override has also been programmed, you can transmit over the
  • Kenwood NX-1300N | User Manual 4 - Page 85
    © 2020
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
B5A-3233-00/01_XMC_EN
USER MANUAL
NX-1000 series