Kenwood NX-5700 User Manual 2

Kenwood NX-5700 Manual

Get Kenwood NX-5700 PDF manuals and user guides View all Kenwood NX-5700 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood NX-5700 manual content summary:

  • Kenwood NX-5700 | User Manual 2 - Page 1
    .. . NX-5000 series USER MANUAL The picture shows the model with an operation panel attached. B5A-0395-40/05 (K)
  • Kenwood NX-5700 | User Manual 2 - Page 2
    CONTENTS SCREEN DISPLAY ...3 BASIC OPERATIONS ...4 SWITCHING POWER ON/ OFF 4 ADJUSTING THE VOLUME ...5 SELECTING A ZONE AND CHANNEL 5 Bluetooth ...63 microSD CARD & BUILT-IN MEMORY 75 INDICATOR LIST ...82 This manual has been prepared based on basic settings. Depending on the setting, the
  • Kenwood NX-5700 | User Manual 2 - Page 3
    SCREEN DISPLAY The display on the screen differs as follows depending on the type of panel used. o When the attached panel or KCH-19 (Basic Panel) is used o When KCH-20R (Featured Panel) is used o When KCH-21R (Handheld Control Head) is used 3
  • Kenwood NX-5700 | User Manual 2 - Page 4
    Mode. ● If a password has been registered and the [Transceiver Password] function has not been programmed to a key or configured to the menu, the transceiver enters Transceiver Password Mode when the power is turned on. 2 Enter a number using the [J] and [K] keys. ● On an optional microphone with
  • Kenwood NX-5700 | User Manual 2 - Page 5
    the transceiver remains locked. ● The password can contain a maximum of 6 digits. ADJUSTING THE VOLUME Press the key programmed as [Volume Up] to increase the volume. Press the key programmed as [Volume Down] to decrease the volume. SELECTING A ZONE AND CHANNEL 1 Select the desired zone using the
  • Kenwood NX-5700 | User Manual 2 - Page 6
    . o Making Group Calls (P25 Conventional) You can select a Talkgroup ID from the list to make a call to those parties on a Conventional channel. 1 Press the key programmed as [Group], [Group + Status] or [Group + Short Message] to enter Talkgroup ID Select Mode. Alternatively, press the key
  • Kenwood NX-5700 | User Manual 2 - Page 7
    to specific persons on a Conventional channel. 1 Press the key programmed as [Individual], [Individual + Status] or [Individual + Short into your transceiver. Alternatively, you can enter a unit ID manually. ● Press the [ ] key to enter the manual input mode. Press the [J] and [K] keys to enter the
  • Kenwood NX-5700 | User Manual 2 - Page 8
    wait for the channel to become free. When the traffic channel becomes free, a proceed tone sounds. 1 Select the configured Talkgroup channel using the keys programmed as [Channel Up]/ [Channel Down]. 2 Press and hold the PTT switch to make the call. ● "Calling" appears on the display while the call
  • Kenwood NX-5700 | User Manual 2 - Page 9
    Short Message] to enter Individual Call Mode. Alternatively, press the key programmed as [Menu] to enter Individual Call Mode using the Menu Mode. on the display. Alternatively, you can enter a unit ID manually. ● Press the [ ] key to enter the manual input mode. Press the [J] and [K] keys to enter
  • Kenwood NX-5700 | User Manual 2 - Page 10
    ID from the list to make a call to those parties on a Conventional channel. 1 Press the key programmed as [Group], [Group + Short Message] or [Group + Status] to enter Group Call Mode. Alternatively, press the key programmed as [Menu] to enter Group Call Mode using the Menu Mode. ● The group ID list
  • Kenwood NX-5700 | User Manual 2 - Page 11
    + Status] to enter Individual Call Mode. Alternatively, press the key programmed as [Menu] to enter Individual Call Mode using the Menu Mode. your transceiver. Alternatively, you can enter a unit ID manually. ● Press the [ ] key to enter the manual input mode. Press the [J] and [K] keys to enter
  • Kenwood NX-5700 | User Manual 2 - Page 12
    wait for the channel to become free. When the traffic channel becomes free, a proceed tone sounds. 1 Select the configured Group channel using the keys programmed as [Channel Up]/ [Channel Down]. 2 Press and hold the PTT switch to make the call. ● "Calling" appears on the display while the call is
  • Kenwood NX-5700 | User Manual 2 - Page 13
    your transceiver. Alternatively, you can enter a unit ID manually. ● Press the [ ] key to enter the manual input mode. Press the [J] and [K] keys to caller's voice, readjust the volume as necessary. ● If signaling has been programmed on the selected channel, you will hear a call only if the signal
  • Kenwood NX-5700 | User Manual 2 - Page 14
    the call, press the PTT switch. To deny the call, press the key programmed as [Clear]. After receiving the call, you can respond to the call by as you would during a normal call. After the call is finished, press the key programmed as [Clear] to end the call. o Receiving Group Calls (NXDN) When you
  • Kenwood NX-5700 | User Manual 2 - Page 15
    physical controls. Once you become familiar with the Menu system, you will appreciate the versatility it offers. Some transceiver keys may already be programmed with functions listed in the Menu. Those functions can be accessed directly by pressing the key. All other functions can still be accessed
  • Kenwood NX-5700 | User Manual 2 - Page 16
    display. ● Press the [ ] key at any time to exit Menu mode. KEY MODE Your transceiver operations vary according to the functions that your dealer has programmed onto the transceiver keys. Refer to "FUNCTION LIST" {p. 17} for the available programmable functions. 16
  • Kenwood NX-5700 | User Manual 2 - Page 17
    Conv. FUNCTION LIST PF Key: Functions that can be programmed to the transceiver keys Menu: Functions that can be accessed Telephone Auto Telephone p p N/A N/A N/A N/A Autodial Auto Dial p p p p N/A N/A Autodial Programming Auto Dial Prog p p p p p p AUX A AUX A pppppp AUX B AUX B pppppp
  • Kenwood NX-5700 | User Manual 2 - Page 18
    Mic Sense External Speaker Fixed Volume Format SD Card Front Panel Programming Function GPS GPS/ Bluetooth Reset GPS Position Display Group *3 Group + Short Message *3 Group + Status *3 Group ID/ Channel Entry High Transmit Power Home Channel Home Channel Select Horn Alert Individual *3 Individual
  • Kenwood NX-5700 | User Manual 2 - Page 19
    Manual Site Hunt Master Volume Control Medium Transmit Power Menu Mobile Relay Station Mic Sense Microphone Type Monitor Monitor Momentary Multi RF Deck View Operator Selectable Tone OST Down OST List OST Up OVCM Playback Playback (Last Recording) Priority-channel Select Public Address Radio
  • Kenwood NX-5700 | User Manual 2 - Page 20
    Conv. Function Menu Display RX Audio Equalizer (High) RX EQ High N/A p p p p p RX Audio Equalizer (High Midrange) RX EQ High Mid N/A p p p p p Delete/ Add Scan Del/Add pppppp Scan Normal Scan Normal pppppp Scan Program Scan Program p p p p p p Scrambler/ Encryption Scram/Encryp p p
  • Kenwood NX-5700 | User Manual 2 - Page 21
    Password Password pppppp TX Audio Equalizer (High) TX EQ High N/A p p p p p TX Audio Equalizer (High Midrange) TX EQ High Mid N/A p p p p Function None 2-tone ANR Preset Audio Profile Auto Dimmer *1 Auto Telephone Autodial Autodial Programming Menu Display - p N/A p p p 2-tone p p N/A p p
  • Kenwood NX-5700 | User Manual 2 - Page 22
    Display Format Eject SD Card Emergency *2 External Mic Sense External Speaker Fixed Volume Format SD Card Front Panel Programming 22 AUX A AUX B AUX C Bluetooth BT Device Discoverable ppppp ppppp ppppp p N/A p p p p N/A p p p p N/A p p p ppppp p N/A p p p N/A p p p p N/A p p p p BT Headset Typ
  • Kenwood NX-5700 | User Manual 2 - Page 23
    Short Message *3 Group + Status *3 Group ID/ Channel Entry High Transmit Power Home Channel Home Channel Select Horn Alert Individual *3 Individual + Short Brightness Lone Worker Low Transmit Power Maintenance Manual Site Hunt Master Volume Control Medium Transmit Power Menu Mobile Relay Station Mic
  • Kenwood NX-5700 | User Manual 2 - Page 24
    Select Public Address Radio Check Radio Inhibit Radio Uninhibit Regroup High) RX Audio Equalizer (High Midrange) RX Audio Equalizer (Midrange) RX Audio Equalizer (Low Midrange) RX Audio Equalizer (Low) RX Auto Gain Control Save GPS Data Save Log Data Scan Scan Delete/ Add Scan Normal Scan Program
  • Kenwood NX-5700 | User Manual 2 - Page 25
    Select System Up Tactical Zone Talk Around Talkgroup Reset Task Request Confirmation Telephone Disconnect Transceiver Password TX Audio Equalizer (High) TX Audio Equalizer (High Midrange) TX Audio Equalizer (Midrange) TX Audio Equalizer (Low Midrange) TX Audio Equalizer (Low) TX Auto Gain Control
  • Kenwood NX-5700 | User Manual 2 - Page 26
    Del/ Add - ppppp p p p N/A N/A p N/A p p p p N/A p p p *1 Auto Dimmer is not available on the KCH-21R Handheld Control Head. *2 Emergency can be programmed only on the Auxiliary (orange) key. *3 Group, Group + Short Message, Group + Status, Individual, Individual + Short Message and Individual
  • Kenwood NX-5700 | User Manual 2 - Page 27
    contact your dealer. ● Texts in the < > brackets are the displays for the key guides. o None No function has been programmed. o 2-tone Allows you to quickly call the 2-tone list that have been programmed onto your transceiver. o ANR Preset Cancels the background noise to improve the audio
  • Kenwood NX-5700 | User Manual 2 - Page 28
    o AUX C Toggles the auxiliary port C ON and OFF. When toggled on, the optional feature connected to the auxiliary port C will be activated and the indicator will appear on the display. o AUX Output ID 1 ~ 3 Toggles the auxiliary output ID port ON and OFF. When toggled on, the
  • Kenwood NX-5700 | User Manual 2 - Page 29
    o Call Response Press this key to respond to an Individual Call. When an Individual Call is received, the Alert tone stops. o Channel Down Press this key to decrease the channel number. {p. 5} o Channel Entry Press this key to enter Channel Entry Mode, to select a channel. o
  • Kenwood NX-5700 | User Manual 2 - Page 30
    frequency and other data of a Conventional channel and to add new Conventional channels using your transceiver even when the FPU (Field Programming Unit) software or a computer is not available. o Function Press this key, then press a programmable key to activate its secondary function. o GPS
  • Kenwood NX-5700 | User Manual 2 - Page 31
    other operating systems, this key functions the same as Channel Entry. o High Transmit Power Turns High Transmit Power on or off. When using a channel programmed with low or medium power, this allows you to change the output power to high. o Home Channel Press this key to jump to your
  • Kenwood NX-5700 | User Manual 2 - Page 32
    . When using a channel programmed with medium or high power, this allows you to change the output power to low. o Maintenance Allows you to display the signal strength, site information and Bit Error Rate (BER) on the LCD when constructing the system or during maintenance. o Manual Site Hunt
  • Kenwood NX-5700 | User Manual 2 - Page 33
    o Mic Sense Allows you to change the microphone sensitivity. o Microphone Type Allows you to select a microphone type that suits the optional external microphone connected. o Monitor Allows you to turn the transceiver signaling off, to listen to all calls that are received on the channel. o
  • Kenwood NX-5700 | User Manual 2 - Page 34
    communicated or not. o Radio Inhibit Allows you to inhibit the transceiver operation by remote control. o Radio Uninhibit Allows you to 1 order. o RX Audio Equalizer (High) Allows you to set the audio response for high frequencies. o RX Audio Equalizer (High Midrange) Allows you to set the audio response
  • Kenwood NX-5700 | User Manual 2 - Page 35
    the Scan List and Priority channels using your transceiver. Refer to "SCAN PROGRAMMING" {p. 41} . o Scrambler/ Encryption Allows you to station. ● You need to connect the KRA-40 GPS antenna. ● When the power is turned ON and/or the reception condition of the GPS satellite is poor,
  • Kenwood NX-5700 | User Manual 2 - Page 36
    o Short Message Allows you to send short messages such as an address, telephone number, etc. o Site Down Press this key to decrease the site number. o Site Lock Allows you to lock the current site. The transceiver will not be able to search for alternate sites, and "Site Lock"
  • Kenwood NX-5700 | User Manual 2 - Page 37
    the current Trunking site. With the site displayed, press and hold the key programmed as [System Search] to enter Search mode. The transceiver begins searching for a a Task Request message of which the operator will check the instructions in the message and return a response message such as task
  • Kenwood NX-5700 | User Manual 2 - Page 38
    High) Allows you to set the audio response for high frequencies. o TX Audio Equalizer (High Midrange) Allows you to set the audio response for high selected. o Voice Memo Allows you to record audio near the transceiver manually. o Volume Down Press this key to decrease the volume level.
  • Kenwood NX-5700 | User Manual 2 - Page 39
    o Zeroize Allows you to delete the Encryption keys stored in a Secure Cryptographic Module (SCM), configured in the built-in DES or configured with Enhanced Encryption. o Zone Delete/ Add Allows you to include or omit each Zone in the Multi-Zone scan sequence. o Zone Down
  • Kenwood NX-5700 | User Manual 2 - Page 40
    is no longer present. When the signal "drops out", the transceiver will remain on the channel momentarily before Scan resumes. This delay time is programmed by your dealer. If a signal is received during the delay time, the transceiver will remain on the same channel. To stop scanning, press the
  • Kenwood NX-5700 | User Manual 2 - Page 41
    back" on the current channel. If the channel has been changed, the newly selected channel is assigned as the new revert channel. SCAN PROGRAMMING Note: ● Scan programming is only available when Scan Type has been set to "List". o Scan List Editing You can reprogram your scan list to add or delete
  • Kenwood NX-5700 | User Manual 2 - Page 42
    1 Select the channel where the scan list to be edited has been set, press the key programmed as [Scan Program] to enter Scan Program Mode. Alternatively, press the key programmed as [Menu] to enter Scan Program Mode using the Menu Mode. 2 Press the [ ] key to edit the Priority channel. 3 Press the
  • Kenwood NX-5700 | User Manual 2 - Page 43
    (DUAL TONE MULTI FREQUENCY) CALLS Note: ● DTMF calls can be made only in Analog Conventional and NXDN Conventional Operation. MAKING A DTMF CALL o Manual Dialing (Microphone keypad only) 1 Press and hold the PTT switch. 2 Enter the desired digits using the microphone keypad. ● The corresponding DTMF
  • Kenwood NX-5700 | User Manual 2 - Page 44
    5 Press the [ ] key to confirm your selection. 6 Press the [ ] key to exit Autodial Programming Mode. o Manual Dialing 1 Press the key programmed as [Autodial] to enter Autodial Mode. Alternatively, press the key programmed as [Menu] to enter Autodial Mode using the Menu Mode. ● The last called unit
  • Kenwood NX-5700 | User Manual 2 - Page 45
    press the key programmed as [Menu] to enter Autodial Mode using the Menu Mode. ● The last called unit appears on the display. 2 Press the [J] and [K] keys to select your desired list number. 3 Press the PTT switch to make the call. MAKING A TELEPHONE CALL (LTR TRUNKING) o Manual Dialing 1 Select the
  • Kenwood NX-5700 | User Manual 2 - Page 46
    function, you can make emergency calls. Note: ● Only the Auxiliary (orange) key can be programmed with the Emergency function. 1 Press and hold the key programmed as [Emergency]. ● Depending on the delay time programmed into your transceiver, the length of time you must hold the Emergency key will
  • Kenwood NX-5700 | User Manual 2 - Page 47
    hardware cryptographic module developed by JVC KENWOOD to provide cryptographic securities for digital two way radios. ● The transceiver includes a built- the key programmed as [Scrambler/ Encryption Code] to enter Scrambler/ Encryption Code Mode. Alternatively, press the key programmed as [Menu
  • Kenwood NX-5700 | User Manual 2 - Page 48
    and Enhanced Encryption only) 1 Press the key programmed as [Key Delete] to enter Key Delete Mode. Alternatively, press the key programmed as [Menu] to enter Key Delete Mode automatically delete all the Encryption keys. ● Turning the transceiver power OFF and the ON again will not reset the number
  • Kenwood NX-5700 | User Manual 2 - Page 49
    tone or code. o Operator Selectable Tone (OST) If a key has been programmed with [Operator Selectable Tone], you can reprogram the QT tone or DQT code on the correct NAC is received. RADIO ACCESS NUMBER (RAN) RAN is a signaling system designed for digital radio communications. When a channel is set
  • Kenwood NX-5700 | User Manual 2 - Page 50
    2-tone Signaling opens the squelch only when your transceiver receives a call containing a matching 2-tone signal. 1 Press the key programmed as [2-tone]. ● Alternatively, you can press the key programmed as [Menu] to enter 2-tone Mode using the Menu Mode. 2 Press the [J] and [K] keys to select your
  • Kenwood NX-5700 | User Manual 2 - Page 51
    If activated by your dealer, the time will be displayed when the transceiver power is turned ON. Note: ● Removing or leaving the battery pack uncharged time: 1 Press the key programmed as [Clock Adjustment] to enter Clock Adjustment Mode. Alternatively, press the key programmed as [Menu] to enter
  • Kenwood NX-5700 | User Manual 2 - Page 52
    are four available color schemes as follows. Full Color Full Color White Monochrome Black Monochrome White To select a Color Scheme: 1 Press the key programmed as [Menu] to enter Color Scheme Mode using the Menu Mode. 2 Press the [J] and [K] keys to select your desired color scheme. 3 Press the
  • Kenwood NX-5700 | User Manual 2 - Page 53
    MULTI RF DECK VIEW Note: ● This function is only available when the optional KCH-20R featured panel or optional KCH-21R handheld control head is used. This transceiver is equipped with Multi RF Deck and Multi Control Head functions, where up to three RF Decks (transceiver) and up to two Control
  • Kenwood NX-5700 | User Manual 2 - Page 54
    the Selected RF Deck to RF Deck 2 as follows: Alternatively, press the key programmed as [RF Deck Down] or [RF Deck Up] to switch the Selected RF the information of the Selected RF Deck is displayed. Alternatively, press the key programmed as [Menu] to enter Multi RF Deck View Mode using the Menu
  • Kenwood NX-5700 | User Manual 2 - Page 55
    LANGUAGE Your transceiver is equipped with multiple language support feature. You can change the language of selectable are dependent on the dealer setting. For details, consult your dealer. 1 Press the key programmed as [Menu] to enter Language Mode using the Menu Mode. 2 Press the [J]/[K] keys to
  • Kenwood NX-5700 | User Manual 2 - Page 56
    KENWOOD Corporation. FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming Press the [J] and [K] keys to select the station you want to call. ● If Manual Dialing is enabled, you can enter a station ID using the microphone keypad or the
  • Kenwood NX-5700 | User Manual 2 - Page 57
    the [J] and [K] keys to select the status you want to transmit. ● If Manual Dialing is enabled, you can enter a status ID using the microphone keypad or The category list is displayed. However, depending on the stack settings programmed by your dealer, the individual list (Caller ID, Status Message
  • Kenwood NX-5700 | User Manual 2 - Page 58
    to a PC. Ask your dealer for details. ● Long messages can contain a maximum of 4096 characters. GPS REPORT GPS data can be manually transmitted by pressing the key programmed as [Send the GPS Data], or by accessing the Menu {p. 15} . If set up by your dealer, GPS data may be automatically
  • Kenwood NX-5700 | User Manual 2 - Page 59
    be used to operate VOX. o VOX Gain Level Sets the Mic input sensitivity of the VOX operation. 1 Connect a headset to the transceiver. 2 Press the key programmed as [VOX]. ● The current VOX Gain level appears on the display. 3 Press the [J] or [K] key to increase or decrease the VOX Gain level. ● The
  • Kenwood NX-5700 | User Manual 2 - Page 60
    transmit for a period of time that exceeds the programmed time, the transceiver will stop transmitting and an alert tone will When activated, this function decreases the amount of power used when a signal is not being received and service range (Appears on NXDN Trunking and P25 Trunking
  • Kenwood NX-5700 | User Manual 2 - Page 61
    wait until the channel becomes free. However, if BCL Override has also been programmed, you can transmit over the current signal: 1 Press and hold the PTT " appears on the display. If enabled by your dealer, an In-service Tone will sound when an available control channel is detected after the out
  • Kenwood NX-5700 | User Manual 2 - Page 62
    VOICE ANNOUNCEMENT An audio voice will be announced as below by dealer setting. ● When changing the zone and/or channel, the new zone and channel number are announced. ● When changing the status, the new status is announced. ● When changing the function setting, the new setting is announced. 62
  • Kenwood NX-5700 | User Manual 2 - Page 63
    the radio wave conditions. ● Only headsets which support the Headset Profile (HSP) certified by Bluetooth SIG can be used with the transceiver. However, operations are not guaranteed in all headsets. ● Refer to the following URL for details on the Bluetooth devices operationally tested by KENWOOD
  • Kenwood NX-5700 | User Manual 2 - Page 64
    as [Bluetooth] to turn the Bluetooth function on or off. Alternatively, press the key programmed as [Menu] to enter Bluetooth Mode using the Menu Mode. Press the [J] and [K] keys to select "On" or "Off". Press the [ ] key to confirm your
  • Kenwood NX-5700 | User Manual 2 - Page 65
    4 Press the [ ] key or the [J] and [K] keys to select "Find Device". The transceiver starts to search for available Bluetooth devices. Up to 16 devices can be found and listed on the display. ● The search will end after approximately 30 or 40 seconds (depending on whether or not the Bluetooth Data
  • Kenwood NX-5700 | User Manual 2 - Page 66
    the key programmed as [Bluetooth Connect/ Disconnect]. ● The LED indicator blinks in blue. ● For Bluetooth devices that does not support Simple Secure Pairing time the transceiver and headset are powered on. If the headset cannot be used automatically, connect manually using the My Device setting in
  • Kenwood NX-5700 | User Manual 2 - Page 67
    to connect once it received the request from the PC. Once the connection has been established, your transceiver can start communicating with the Field Programming Unit (FPU) or you can use the PC Interface Protocol. ● The " " indicator appears on the display. The transceiver transits to each mode
  • Kenwood NX-5700 | User Manual 2 - Page 68
    registered to the transceiver and to switch the speaker audio output. o Connecting/ Disconnecting/ Deleting a registered device using My Devices Press the key programmed as [Menu] to enter Bluetooth My Devices Mode using the Menu Mode. To connect a device: 1 Press the [ ] key or the [J] and [K] keys
  • Kenwood NX-5700 | User Manual 2 - Page 69
    3 Press the [ ] key to confirm the connection. ● The LED indicator blinks in blue while the transceiver is connecting to the device, "Connecting" appears on the display. "Connected" appears when the connection is established. To disconnect a device: 1 Press the [ ] key or the [J] and [K] keys to
  • Kenwood NX-5700 | User Manual 2 - Page 70
    3 Press the [ ] key to confirm the disconnection. ● The " " indicator and "Disconnected" appear on the display. To delete a device: Note: ● Make sure the device to be deleted has been disconnected. 1 Press the [ ] key or the [J] and [K] keys to select the device to delete. 2 Press the [ ] key to
  • Kenwood NX-5700 | User Manual 2 - Page 71
    o Checking the information of the devices 1 Press the key programmed as [Menu] to enter Bluetooth My Devices Mode using the Menu Mode. 2 Press the [J] and [K] keys to select the device to display its information. 3 Press
  • Kenwood NX-5700 | User Manual 2 - Page 72
    BT Name [ H ] key [ H ] key [ I ] key Class [ H ] key [ I ] key BT Address [ I ] key Device Class Audio/Video Phone Computer LAN/Network Peripheral Imaging Wearable Toy Health 72 Disconnected Connected
  • Kenwood NX-5700 | User Manual 2 - Page 73
    between the speaker of the transceiver and the Bluetooth headset. Press the key programmed as [Bluetooth Speaker] repeatedly to change the setting ("Off", "Only" or "Both(BT+Radio)"). Alternatively, press the key programmed as [Menu] to enter Bluetooth Speaker Mode using the Menu Mode. Press the
  • Kenwood NX-5700 | User Manual 2 - Page 74
    ) connection or Serial Port Profile (SPP) connection. The Bluetooth device has rejected a request for pairing or Headset Profile (HSP) connection. The Bluetooth device does not support Headset Profile (HSP) connection.
  • Kenwood NX-5700 | User Manual 2 - Page 75
    files are stored in their respective folders. Up to 250 files can be stored in each folder. PRIVATE KENWOOD GPS 㧦 Folder 㧦 File GPS_M SAVED 1. Rename AR_20140110_174530 20140110_174530_AR_N65519.WAV 001 20140110_180010_AR_A16777215.WAV 002 20140121_194915_AR_---.WAV 003 20140129_100835_AR_
  • Kenwood NX-5700 | User Manual 2 - Page 76
    Storage (Auto). GPS_M *3 Stores GPS data files saved using GPS Data Storage (Manual). *1 If the folder has reached its maximum limit of 250 files, the current folder is available for storing GPS data files saved using GPS Data Storage (Manual). Up to 2000 GPS data can be saved in a file. If the
  • Kenwood NX-5700 | User Manual 2 - Page 77
    data file in the GPS folder with the same date as the current saving date. GPS Data Storage (Manual) When all the following conditions are satisfied. ● NMEA of any of the Record Format (Manual/Auto) is enabled. ● The Save GPS Data key, GPS Position Display key, Menu key for executing Save GPS
  • Kenwood NX-5700 | User Manual 2 - Page 78
    - When the power cable is unplugged ● You programmed as [Menu] to enter Voice Memo mode using the Menu Mode. ● Recording starts on the transceiver. ● The transceiver will exit Voice Memo mode and stop the recording automatically after 10 minutes into the recording. 2 To stop the recording manually
  • Kenwood NX-5700 | User Manual 2 - Page 79
    . For more details, consult your dealer. o GPS Data Storage (Manual) The GPS data can be manually stored in the microSD card using one of the key operations below. ● Press the key programmed as [Save GPS Data]. ● Press the key programmed as [GPS Position Display] to enter the GPS Position Display
  • Kenwood NX-5700 | User Manual 2 - Page 80
    , press the [H]/ [I] key. Press and hold the key to fast-forward or rewind. o To play back the last recording directly Press the key programmed as [Playback (Last Recording)] to play back the latest audio data recorded using the Auto Recording function. o To save a recording 1 Press the [ ] key
  • Kenwood NX-5700 | User Manual 2 - Page 81
    o To delete a folder 1 Press the [ ] key while the folder list is displayed. Then press the [ ● A confirmation message appears on the display. 2 Press the [ ] key to delete. ] key. 81
  • Kenwood NX-5700 | User Manual 2 - Page 82
    INDICATOR LIST Indicator Description Displays the signal strength. The channel is using high transmit power. The channel is using medium transmit power. The channel is using low transmit power. In Digital mode (Digital Channel) In Analog mode (Analog Channel) In Digital mode (Mixed Channel) In
  • Kenwood NX-5700 | User Manual 2 - Page 83
    . The System Lock is activated. The Broadcast Call function is activated. The Surveillance function is activated. Appears when the selected group is programmed as telephone IDs. Blinks during Auto Telephone search. The Tactical Zone is activated. The Horn Alert function is activated. The Public
  • Kenwood NX-5700 | User Manual 2 - Page 84
    © 2018
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
NX-5000 series
USER MANUAL
The picture shows the model with an operation panel attached.
B5A-0395-40/05 (K)