Kenwood NX-700H Operation Manual

Kenwood NX-700H Manual

Get Kenwood NX-700H PDF manuals and user guides View all Kenwood NX-700H manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood NX-700H manual content summary:

  • Kenwood NX-700H | Operation Manual - Page 1
    NX-700H(T) NX-800H(T) VHF DIGITAL TRANSCEIVER/ UHF DIGITAL TRANSCEIVER INSTRUCTION MANUAL © B62-2457-00 (K) 09 08 07 06 05 04 03 02 01 00
  • Kenwood NX-700H | Operation Manual - Page 2
    radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO
  • Kenwood NX-700H | Operation Manual - Page 3
    are grateful you have chosen KENWOOD for your personal mobile applications. This instruction manual covers only the basic operations etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if
  • Kenwood NX-700H | Operation Manual - Page 4
    ◆ The transceiver operates in 12 V negative ground systems only! Check the battery polarity and voltage of the vehicle before installing the transceiver. ◆ Use only a KENWOOD optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable. For passenger safety, install the
  • Kenwood NX-700H | Operation Manual - Page 5
    CONTENTS UNPACKING AND CHECKING EQUIPMENT 1 SUPPLIED ACCESSORIES 1 PREPARATION 2 TOOLS REQUIRED 2 POWER CABLE CONNECTION 2 INSTALLING THE TRANSCEIVER 3 GETTING ACQUAINTED 4 FRONT PANEL 4 DISPLAY ...5 PROGRAMMABLE FUNCTIONS 6 BASIC OPERATIONS 7 SWITCHING POWER ON/OFF 7 ADJUSTING THE VOLUME
  • Kenwood NX-700H | Operation Manual - Page 6
    -OUT TIMER (TOT 20 SIGNAL STRENGTH INDICATOR 20 COMPANDER 20 BUSY CHANNEL LOCKOUT (BCL 20 CONTROL CHANNEL HUNT 20 PTT ID ...20 VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT 21 VOICE RECORDER 21 VOICE
  • Kenwood NX-700H | Operation Manual - Page 7
    CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. Carefully unpack • 5 x 16 mm self-tapping screw 4 • Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 • Instruction manual 1 1
  • Kenwood NX-700H | Operation Manual - Page 8
    his/her aid in determining if they will perform normally while transmitting. Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. TOOLS REQUIRED Note: Before installing the transceiver, always check how far the
  • Kenwood NX-700H | Operation Manual - Page 9
    INSTALLING THE TRANSCEIVER For passenger safety, install the transceiver securely using an optional mounting bracket and screw set so the transceiver will not break loose in the event of a collision. 1 Mark the position of the holes in the dash by using the mounting bracket as a template. Drill the
  • Kenwood NX-700H | Operation Manual - Page 10
    GETTING ACQUAINTED FRONT PANEL Optional microphone a (power) switch Press and hold to switch the transceiver power ON and OFF. b key Press to activate its programmable function {page 6}. The default is Volume Up. c key Press to activate its programmable function {page 6}. The default is Volume Down.
  • Kenwood NX-700H | Operation Manual - Page 11
    l key Press to activate its programmable function {page 6}. The default is Zone Up. m key Press to activate its programmable function {page 6}. n Speaker Internal speaker o PTT (Push-to-Talk) switch Press and hold this switch, then speak into the microphone to call a station. DISPLAY Indicator
  • Kenwood NX-700H | Operation Manual - Page 12
    PROGRAMMABLE FUNCTIONS Following is a list of available programmable functions. Contact your dealer for details on those functions which have been programmed on your transceiver. • 2-tone 1 • Auto Reply Message 2 • Auto Telephone 3 • Autodial • Autodial Programming • AUX A • AUX B • Broadcast 5 •
  • Kenwood NX-700H | Operation Manual - Page 13
    BASIC OPERATIONS SWITCHING POWER ON/OFF Press and hold the switch for approximately 1 second to turn the transceiver power ON. Press and hold the switch again to turn the transceiver OFF. ■ Transceiver Password If the transceiver is password protected, "PASSWORD" will appear on the display when the
  • Kenwood NX-700H | Operation Manual - Page 14
    3 Press the PTT switch and speak into the microphone. Release the PTT switch to receive. • For best sound quality, hold the microphone approximately 1.5 inches (3 ~ 4 cm) from your mouth. ■ Making Group Calls (Digital) If a key has been programmed with [Group] or [Group + Status], you can select a
  • Kenwood NX-700H | Operation Manual - Page 15
    MENU MODE Many functions on this transceiver are selected or configured through the Menu instead of physical controls. Once you become familiar with the Menu system, you will appreciate the versatility it offers. MENU ACCESS 1 Press the key programmed as [Menu]. 2 Press / to select a Menu item. •
  • Kenwood NX-700H | Operation Manual - Page 16
    Menu GPS POS DISP GROUP GROUP+STATUS GROUP+SDM HOME CH SEL HORN ALERT INDIVIDUAL INDIV+STATUS INDIV+SDM LCD BRIGHTNESS LONE WORKER MAINTENANCE MONITOR OST OST LIST PLAYBACK PRI CH SEL RX AUDIO EQ RX AGC RX LOW CUT PUBLIC ADDRESS SCAN SCAN DEL/ADD SCRAM/ENCRYP SCRAM CODE SELCALL SELCALL+STATUS
  • Kenwood NX-700H | Operation Manual - Page 17
    Menu SQUELCH OFF STACK STATUS SHORT MESSAGE TALK AROUND TX AUDIO EQ TX AGC TX NOISE SUPPR PASSWORD VOICE MEMO ZONE DEL/ADD Description Squelch Off ON/OFF Stack mode Status mode Short Message mode Talk Around ON/OFF TX Audio Equalizer mode TX Audio Gain Control mode TX Noise Suppressor mode
  • Kenwood NX-700H | Operation Manual - Page 18
    SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a signal is present. To begin scanning, press the key programmed as [Scan]. • The icon appears on the display. • When a signal is detected on a channel,
  • Kenwood NX-700H | Operation Manual - Page 19
    SCAN DELETE/ADD You can add and remove zones and/or channels/group IDs to and from your scan list. 1 Select your desired zone and/or channel/group ID. 2 Press the key programmed as [Zone Delete/Add] (to add/remove zones) or [Scan Delete/Add] (to add/remove channels/group IDs). • You can also press
  • Kenwood NX-700H | Operation Manual - Page 20
    2-way Paging Function, and is a protocol owned by JVC KENWOOD Corporation. Note: This function is available only in analog operation. the station you want to call. • If you are using a microphone keypad and Manual Dialing is enabled, you can directly enter the station ID. 4 Press the PTT switch
  • Kenwood NX-700H | Operation Manual - Page 21
    right. Repeat this process until the entire ID is entered. 4 Press to enter Status mode. 5 Press / to select the status you want to transmit. • If Manual Dialing is enabled, you can enter the status ID by using the microphone keypad, or by using / (refer to step 3, above). 6 Press the PTT switch
  • Kenwood NX-700H | Operation Manual - Page 22
    ADVANCED OPERATIONS DTMF (DUAL TONE MULTI FREQUENCY) CALLS ■ Making a DTMF Call Note: DTMF calls can be made only in analog operation. Manual Dialing 1 Press and hold the PTT switch. 2 Enter the desired digits using the microphone keypad. • If you release the PTT switch, transmit mode will end
  • Kenwood NX-700H | Operation Manual - Page 23
    TELEPHONE CALLS ■ Making a Telephone Call Manual Dialing (Analog) 1 Select your desired zone and telephone group ID. 2 Press the PTT switch to start the call. 3 Enter your desired digits using the microphone
  • Kenwood NX-700H | Operation Manual - Page 24
    SCRAMBLER Press the key programmed as [Scrambler/ Encryption], or access the Menu {page 9}, to switch the transceiver to secure (encrypted) transmission. • Pressing the microphone PTT switch after the Scrambler function has been turned ON encrypts the transmitted signal. SIGNALING ■ Quiet Talk (QT)/
  • Kenwood NX-700H | Operation Manual - Page 25
    CLOCK If activated by your dealer, you can view the clock any time by pressing the key programmed as [Clock]. Note: Removing the transceiver power for extended periods will clear the clock time. To set the time: 1 Press the key programmed as [Clock Adjustment]. • The current time setting appears. 2
  • Kenwood NX-700H | Operation Manual - Page 26
    BACKGROUND OPERATIONS Your dealer can activate a variety of transceiver functions to perform without any additional operation on your part. TIME-OUT TIMER (TOT) The Time-out Timer is used to prevent you from using a channel for an extended duration. If you continuously transmit for a preset time,
  • Kenwood NX-700H | Operation Manual - Page 27
    VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT VOICE RECORDER The voice recorder allows you to record conversations and create voice memos. ■ Auto Recording If activated, the auto recorder will continuously
  • Kenwood NX-700H | Operation Manual - Page 28
    end the recording at any time by pressing . • To delete the selected recording, press . To clear all the recorded data, press and hold . VOICE GUIDE When changing the zone and/or channel, an audio voice will announce the new zone and channel. Additionally, when changing a function setting, the new
  • Kenwood NX-700H | Operation Manual - Page 29
    NX-700H(T) NX-800H(T) VHF UHF
  • Kenwood NX-700H | Operation Manual - Page 30
  • Kenwood NX-700H | Operation Manual - Page 31
    KENWOOD NEXEDGE 150 i
  • Kenwood NX-700H | Operation Manual - Page 32
    地的 KENWOOD KENWOOD 12 V KENWOOD ii
  • Kenwood NX-700H | Operation Manual - Page 33
    目錄 1 1 2 2 2 3 4 4 5 6 7 7 7 ID 7 發射...7 接收...8 9 9 9 11 掃描 ...12 12 12 12 13 13 FleetSync 14 14 14 15 GPS 15 iii
  • Kenwood NX-700H | Operation Manual - Page 34
    16 DTMF 16 17 17 加密...18 信號...18 時鐘...19 LCD 19 19 PA 19 20 TOT 20 20 20 BCL 20 20 PTT ID ...20 VGS-1 21 21 22 iv
  • Kenwood NX-700H | Operation Manual - Page 35
    KENWOOD KENWOOD 1 15 A)...2 1 • 5 x 16 mm 4 4 4 4 1 1
  • Kenwood NX-700H | Operation Manual - Page 36
    準備工作 KENWOOD KENWOOD 所需工具 6 mm 4.2 mm 12 V KENWOOD 1 2 3 4 2
  • Kenwood NX-700H | Operation Manual - Page 37
    1 2 3 4 六角螺絲 平面墊片 保險絲 12 V 3
  • Kenwood NX-700H | Operation Manual - Page 38
    前面板 熟悉本機 a b 6 c 6 d 6 ID 增」。 e 6 ID 減」。 f g LED h 6 頁}。 i 6 j 6 k 6 4
  • Kenwood NX-700H | Operation Manual - Page 39
    l 6 m 6 頁}。 n o PTT 顯示幕 指示燈 ID OST ID 20 VGS-1 AUX A AUX B 功能。 5
  • Kenwood NX-700H | Operation Manual - Page 40
    • 2-音 1 2 3 • AUX A • AUX B • 廣播 5 • 呼叫 1 ~ 6 ID ID ID CW 訊息 6 ID 1 ~ 5 ID 選擇 1 ~ 5 7 5 GPS NXDN) 6 SDM (NXDN) 8 NXDN) 8 ID ID NXDN) 8 SDM (NXDN) 8 NXDN) 8 • LCD 9 9 • OST 1 • 重播 2 10 8 • SDM (FleetSync/NXDN FleetSync) 4 SDM (FleetSync) 4 FleetSync) 4 • 發送
  • Kenwood NX-700H | Operation Manual - Page 41
    基本操作 1 開關則 1 2 3 1 和 2 4 6 ID ID ID ID 9 ID。 發射 1 ID。 2 3 按下 PTT PTT 3 至 4 7
  • Kenwood NX-700H | Operation Manual - Page 42
    ID ID： 1 2 ID/名稱。 3 PTT 1 2 ID。 ID。 3 PTT 18 ID ID ID ID ID PTT 8
  • Kenwood NX-700H | Operation Manual - Page 43
    選單模式 選單存取 1 2 3 4 1 3 和 4。 5 選單設定 選單 說明 2 AUX A AUX B 1 GPS 2 AUX A AUX B ID 1 ~ 5 GPS 9
  • Kenwood NX-700H | Operation Manual - Page 44
    SDM SDM LCD OST OST SDM 發送 GPS 10 SDM ID SDM 模式 LCD OST OST SDM GPS
  • Kenwood NX-700H | Operation Manual - Page 45
    字元輸入 1 A ~ Z、0 ~ 9 A ~ Z、 a ~ z、0 ~ 9 2 DTMF 鍵 字元循環 1 1 2 ABC 2 3 D E F 3 4 G H I 4 5 J K L 5 6 M N O 6 7 P Q R S 7 8 T U V 8 9 W X Y Z 9 0 [空格] 0 11
  • Kenwood NX-700H | Operation Manual - Page 46
    掃描 • 2 優先掃描 1 2 2 1 1。 主掃描 PTT ID 1 ID 2 ID 1 ID 2 ID 1 ID 2 ID 1 ID 2 12
  • Kenwood NX-700H | Operation Manual - Page 47
    ID。 1 ID。 2 道/群 ID 1 ID。 2 3 ID 1 ID 2 ID 1&2」( )。 4 13
  • Kenwood NX-700H | Operation Manual - Page 48
    FleetSync FleetSync JVC KENWOOD Corporation ■ 發射 1 2 3 ID。 4 按下 PTT ID PTT ID 代碼為 3 位 Fleet 號碼和 4 位 ID ID。 • 輸入 Fleet 號碼 (100 ~ 349 ID 號碼 (1000 ~ 4999 ID (在 FPU Fleet ID ID ID ID 2 16 10 到 99 (保留
  • Kenwood NX-700H | Operation Manual - Page 49
    3 ID ID。 4 5 ID 3)。 6 按下 PTT ■ 接收 ID 1 2 I ID；S M 1 ID ID 3 1 PC GPS 報告 GPS GPS GPS 9 GPS 資料。 15
  • Kenwood NX-700H | Operation Manual - Page 50
    進階操作 DTMF DTMF 呼叫 注：DTMF 1 PTT 開關。 2 PTT PTT PTT 1 2 30 11 頁}。 3 按下 PTT DTMF 號碼。 1 9 頁}。 2 01 ~ 32)。 3 按下 PTT 16
  • Kenwood NX-700H | Operation Manual - Page 51
    1 ID。 2 按下 PTT 3 1 ID。 2 3 4 按下 PTT PTT 1 2 17
  • Kenwood NX-700H | Operation Manual - Page 52
    9 PTT 信號 QT DQT QT 或 DQT 信號。QT/ DQT OST OST QT/DQT 設定。 1 2 OST 的鍵達 1 秒鐘。 3 40 4 5 完成 OST OST OST 功能。 RAN) RAN RAN RAN RAN 2 2 2 Tone DTMF 信號：DTMF DTMF FleetSync 14 NXDN ID 信號：NXDN ID 18
  • Kenwood NX-700H | Operation Manual - Page 53
    1 2 3 4 2 和 3 5 LCD 亮度 LCD LCD LCD 9 頁}。 HA PA PA 系統： 1 9 頁}。 • 開啟 PA PA 2 PTT 3 ID 19
  • Kenwood NX-700H | Operation Manual - Page 54
    後台操作 TOT PTT 開關。 強 充足 弱 NXDN 中繼)。 極弱 BCL) BCL BCL 1 PTT 開關。 2 PTT 3 PTT ID PTT ID ID PTT 注：PTT ID 20
  • Kenwood NX-700H | Operation Manual - Page 55
    VGS-1 30 1 單 {第 9 2 3 FleetSync/NXDN 1 2 3 21
  • Kenwood NX-700H | Operation Manual - Page 56
    1 9 頁}。 2 AR RM VM 3 22
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
NX-700H(T)
NX-800H(T)
© B62-2457-00 (K)
09 08 07 06 05 04 03 02 01 00
VHF DIGITAL TRANSCEIVER/
UHF DIGITAL TRANSCEIVER
INSTRUCTION MANUAL