Kenwood NX-P1200AV User Manual

Kenwood NX-P1200AV Manual

Get Kenwood NX-P1200AV PDF manuals and user guides View all Kenwood NX-P1200AV manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood NX-P1200AV manual content summary:

  • Kenwood NX-P1200AV | User Manual - Page 1
    NX-P1200NV NX-P1200AV NX-P1202AV NX-P1300NU NX-P1300AU NX-P1302AU USER MANUAL B5A-3583-00_EN
  • Kenwood NX-P1200AV | User Manual - Page 2
    CONTENTS MODELS COVERED BY THIS MANUAL 4 PREPARATION 5 INSTALLING THE ANTENNA 5 INSTALLING/ REMOVING THE BATTERY PACK 5 INSTALLING THE BELT CLIP 6 INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS 6 INSTALLING THE SPEAKER/ MICROPHONE
  • Kenwood NX-P1200AV | User Manual - Page 3
    46 TIME-OUT TIMER (TOT 46 BATTERY SAVER...46 LOW BATTERY WARNING 46 BUSY CHANNEL LOCKOUT (BCL 46 VOICE ANNOUNCEMENT 47 ALL RESET MODE 48 TROUBLESHOOTING GUIDE 49 SPECIFICATIONS 50 3
  • Kenwood NX-P1200AV | User Manual - Page 4
    MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual: NXDN/ Analog Transceiver NX-P1200NV : VHF TRANSCEIVER NX-P1300NU : UHF TRANSCEIVER Analog Transceiver NX-P1200AV : VHF TRANSCEIVER NX-P1202AV : VHF TRANSCEIVER NX-P1300AU : UHF TRANSCEIVER
  • Kenwood NX-P1200AV | User Manual - Page 5
    PREPARATION INSTALLING THE ANTENNA Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. Antenna INSTALLING/ REMOVING THE BATTERY PACK The battery pack is not charged at the factory; charge it before use.
  • Kenwood NX-P1200AV | User Manual - Page 6
    INSTALLING THE BELT CLIP If necessary, attach the belt clip using the two supplied M3 x 8 mm binding screws. Note: ◆ If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment. ◆ Use the Phillips #2 screwdriver. Belt
  • Kenwood NX-P1200AV | User Manual - Page 7
    INSTALLING THE SPEAKER/ MICROPHONE OR HEADSET Note: ◆ The transceiver is not fully water resistant when using a speaker/ microphone or headset. ◆ Use the Phillips #1 screwdriver. 1 Insert the speaker/ microphone plugs into the speaker/ microphone jacks of the transceiver. 2 Place the locking bracket
  • Kenwood NX-P1200AV | User Manual - Page 8
    ORIENTATION Antenna d e f Battery pack Speaker Microphone ab c a Selector Rotate to change the operating channel. b LED indicator Refer to the "LED Indicator Status" {p. 10}. c Power switch/ Volume control Turn clockwise to switch the transceiver ON. To switch the transceiver OFF, turn
  • Kenwood NX-P1200AV | User Manual - Page 9
    BASIC OPERATION POWER ON Turn the Power switch/ Volume control clockwise to switch the transceiver power ON. • Power-on tone will sound. ADJUST THE VOLUME Rotate the Power switch/ Volume control to adjust the volume. • Clockwise increases the volume and counterclockwise decreases the volume. Note: ◆
  • Kenwood NX-P1200AV | User Manual - Page 10
    RECEIVE VOICE The LED lights green. When the other party transmits it, you hear the voice of the other party. POWER OFF After use, turn off the power. To switch the transceiver power OFF, turn the Power switch/ Volume control fully counterclockwise, until a click sounds. LED Indicator Status
  • Kenwood NX-P1200AV | User Manual - Page 11
    SELF-PROGRAMMING MODE This mode allows you to program the certain transceiver's settings of zone and channel. SELF-PROGRAMMING FLOW Self-programming flow has two patterns depending on the model. NX-P1200NV/ NX-P1300NU (NXDN/ Analog Transceiver) [Side 1] + [PTT] + Power ON Release [Side 1] + [PTT]
  • Kenwood NX-P1200AV | User Manual - Page 12
    NX-P1200AV/ NX-P1202AV/ NX-P1300AU/ NX-P1302AU (Analog Transceiver) [Side 1] + [PTT] + Power ON Release [Side 1] + [PTT] ZONE SELECTION [Side 1] A B [Side 2] Zone 1 Setup Mode [PTT] Zone 2 Setup Mode [PTT] Zone 3 Setup Mode [PTT] Zone 4 Setup Mode [Side 1] A B [Side 2] [PTT] CHANNEL SETUP
  • Kenwood NX-P1200AV | User Manual - Page 13
    DEFAULT CHANNEL SETTINGS This transceiver allows you to reprogram each of the channels with different frequencies and QT tone/DQT code (Analog)/ RAN (NXDN (Digital)) settings. NX-P1200NV Zone 1/ Zone 2 (Analog) Channel Number Table Frequency No. (MHz) Table No. QT (Hz) 1 1 151.6250 1 67.0
  • Kenwood NX-P1200AV | User Manual - Page 14
    NX-P1200AV (Analog Transceiver) Channel Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Table No. 1 1 1 1 1 2 2 2 2 2 20 21 10 12 5 6 Zone 1 ~ Zone 4 Frequency Table (MHz) No. 151.6250 1 151.6250 4 151.6250 8 151.6250 29 151.6250 12 151.9550 1 151.9550 6 151.9550 10 151.9550 29 151.9550 12
  • Kenwood NX-P1200AV | User Manual - Page 15
    NX-P1202AV (Analog Transceiver) Channel Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Table No. 20 21 1 2 10 12 15 26 1 1 1 2 2 2 5 6 Zone 1 Frequency Table (MHz) No. 154.4900 1 154.5150 1 151.6250 1 151.9550 1 151.5125 1 151.6850 1 151.7750 1 158.4000 1 151.6250 4 151.6250 8 151.6250 29
  • Kenwood NX-P1200AV | User Manual - Page 16
    NX-P1300NU (NXDN/ Analog Transceiver) Channel Zone 1/ Zone 2 (Analog) Number Table Frequency No. (MHz) Table No. QT (Hz) 1 1 464.5000 1 67.0 2 1 464.5000 4 77.0 3 1 464.5000 8 88.5 4 1 464.5000 29 179.9 5 1 464.5000 12 100.0 6 2 464.5500 1 67.0 7 2 464.5500 6 82.5 8 2 464.
  • Kenwood NX-P1200AV | User Manual - Page 17
    NX-P1300AU (Analog Transceiver) Channel Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Table No. 1 1 1 1 1 2 2 2 2 2 22 30 32 34 36 38 Zone 1 ~ Zone 4 Frequency Table (MHz) No. 464.5000 1 464.5000 4 464.5000 8 464.5000 29 464.5000 12 464.5500 1 464.5500 6 464.5500 10 464.5500 29 464.5500 12
  • Kenwood NX-P1200AV | User Manual - Page 18
    NX-P1302AU (Analog Transceiver) Channel Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Table No. 2 8 9 10 11 12 13 14 1 3 4 5 6 7 15 16 Zone 1 Frequency Table (MHz) No. 464.5500 1 467.9250 1 461.0375 1 461.0625 1 461.0875 1 461.1125 1 461.1375 1 461.1625 1 464.5000 1 467.7625 1 467.
  • Kenwood NX-P1200AV | User Manual - Page 19
    ID SETUP NXDN ID Setup (Digital) NXDN ID Setup allows you to configure an identification code. NXDN ID (Own unit ID) can be used to identify the transceiver in an NXDN System. You can set the NXDN ID from 00001 to 65519. The default NXDN ID is "00001". To set the NXDN ID 1 With the transceiver
  • Kenwood NX-P1200AV | User Manual - Page 20
    Reserved Group Setup (Digital) Reserved Group Setup allows you to configure the Reserved Group ID. Reserved Group ID is the ID that is the destination of Group Call communication in the channel where Selcall on PTT > Call Type (NXDN) is set to "Reserved Group". You can set the Reserved Group ID from
  • Kenwood NX-P1200AV | User Manual - Page 21
    3 Press the Side 1 or Side 2 button to select the Reserved Group Setup Mode. • The transceiver announces "Group ID". 4 Press the PTT switch to enter the Reserved Group Setup Mode. 5 Turn the Selector to set the pointer to the desired digit (1 ~ 5). • A voice announcement will inform selected number
  • Kenwood NX-P1200AV | User Manual - Page 22
    ZONE SELECTION 1 With the transceiver power OFF, press and hold the Side 1 button and PTT switch while turning the transceiver power ON. • Continue to hold the Side 1 button and PTT switch until the LED lights yellow and the transceiver announces "Self". 2 Release the Side 1 button and PTT switch to
  • Kenwood NX-P1200AV | User Manual - Page 23
    CHANNEL SETUP Frequency Setup To set the Frequency 1 During CHANNEL SETUP, rotate the Selector to select a channel number. • The transceiver announces the zone number and channel number. 2 Press the Side 1 or Side 2 button to select the Frequency Setup Mode. • The transceiver announces "Channel". 3
  • Kenwood NX-P1200AV | User Manual - Page 24
    VHF Frequency Table Table Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Frequency (MHz) 151.625000 151.955000 152.885000 152.915000 151.700000 151.760000 152.945000 151.835000 151.805000 151.512500 151.655000 151.685000 151.715000 151.745000 151.775000 151.865000
  • Kenwood NX-P1200AV | User Manual - Page 25
    UHF Frequency Table Table Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Frequency (MHz) 464.500000 464.550000 467.762500 467.812500 467.850000 467.875000 467.900000 467.925000 461.037500 461.062500 461.087500 461.112500 461.137500 461.162500 461.
  • Kenwood NX-P1200AV | User Manual - Page 26
    Channel Type Setup Set the Channel Type of the selected Zone-Channel to "Analog", "NXDN" (Digital), or "Mixed" (Dual). The following is the transceiver behavior for transmission and reception on a channel with "Mixed" (Dual) configured in Channel Type: Transmission: The transceiver transmits in the
  • Kenwood NX-P1200AV | User Manual - Page 27
    TX Setup When Channel Type is "Mixed" (Dual), set to "Analog" or "NXDN" (Digital) for Transmit Mode. To set the Transmit Mode 1 During CHANNEL SETUP, rotate the Selector to select a channel number. • The transceiver announces the zone number and channel number. 2 Press the Side 1 or Side 2 button to
  • Kenwood NX-P1200AV | User Manual - Page 28
    Operation • If Transmit Mode is set to "Analog", the transceiver will respond to a call in Analog format. • If Transmit Mode is set to "NXDN" (Digital), the transceiver will respond to a call in NXDN format. • In a mixed channel, if the transceiver receives matched Signaling (QT/DQT/ RAN), the
  • Kenwood NX-P1200AV | User Manual - Page 29
    QT/DQT Setup (Analog) Quiet Talk (QT) and Digital Quiet Talk (DQT) are functions that reject undesired signals on your channel. You will hear a call only when you receive a signal that contains a matching QT tone or DQT code. If a call containing a different tone or code is received, squelch will
  • Kenwood NX-P1200AV | User Manual - Page 30
    7 Press the PTT switch to save the settings and return to the ID SETUP/ ZONE SELECTION. • Beep B (2 beeps) will sound. • Turn the transceiver power OFF and then ON return to normal operation with new settings. Note: ◆ If no action is performed for 20 seconds, the transceiver will automatically
  • Kenwood NX-P1200AV | User Manual - Page 31
    DQT Table Table Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 DQT Code D023N D025N D026N D031N D032N D043N D047N D051N D054N D065N D071N D072N D073N D074N D114N D115N D116N D125N D131N D132N D134N D143N D152N D155N D156N D162N D165N D172N
  • Kenwood NX-P1200AV | User Manual - Page 32
    RAN Setup (Digital) RAN (Radio Access Number) is a signaling system designed for NXDN System. When a channel is setup with a RAN, squelch will only open when a call containing a matching RAN is received. If a call containing a different RAN is made on the same channel are using, you will not hear
  • Kenwood NX-P1200AV | User Manual - Page 33
    TX Power Setup To set the Transmit Power 1 During CHANNEL SETUP, rotate the Selector to select a channel number. • The transceiver announces the zone number and channel number. 2 Press the Side 1 or Side 2 button to select the TX Power Setup Mode. • The transceiver announces "TX Power". • If the
  • Kenwood NX-P1200AV | User Manual - Page 34
    CHANNEL CONFIRMATION MODE To confirm your channel settings: 1 With the transceiver power OFF, press and hold the PTT switch while turning the transceiver power ON. • Continue to hold the PTT switch until the LED lights yellow and the transceiver announces "Confirm". 2 Release the PTT switch. • The
  • Kenwood NX-P1200AV | User Manual - Page 35
    BUTTON FUNCTION PROGRAMMING MODE This transceiver allows you to reprogram the Side 1 and Side 2 buttons with any of the functions listed in the table below. Explanations on the use of each function are provided under "PROGRAMMABLE FUNCTIONS" {p. 37}. FUNCTIONS LIST Table Number 0 1 2 3 4 5 6 7 8 9
  • Kenwood NX-P1200AV | User Manual - Page 36
    To set the functions of the Side 1 and Side 2 buttons 1 With the transceiver power OFF, press and hold the Side 1 and Side 2 buttons while turning the transceiver power ON. • Continue to hold the Side 1 and Side 2 buttons until the LED lights yellow and the transceiver announces "Setup". 2 Release
  • Kenwood NX-P1200AV | User Manual - Page 37
    PROGRAMMABLE FUNCTIONS Button Lock Press and hold this button for 1 second to lock the transceiver buttons. • Beep A (1 beep) sounds. Press and hold this button for 1 second again to unlock the transceiver buttons. • Beep B (2 beeps) sounds. The following buttons/ functions can still be used when
  • Kenwood NX-P1200AV | User Manual - Page 38
    Home Channel Allows you to jump to home channel. You can set your own Home Channel by selecting your desired channel using Home Channel Select. 1 Press this button to jump to Home Channel. • Beep A (1 beep) sounds. 2 Press this button again to return to the formerly selected channel. • Beep B (2
  • Kenwood NX-P1200AV | User Manual - Page 39
    Individual Reply Allows you to make an Individual Call to the caller when receiving a Group Call. Group Call receiving transceivers Transceiver that makes Individual Call Transceiver operation Group Call Transceiver A NXDN ID: 00001 Group ID: 00100 PF Button [Individual Reply] Transceiver D
  • Kenwood NX-P1200AV | User Manual - Page 40
    Low Transmit Power Turns Low Transmit Power On or Off. When using a channel programmed with medium or high power, this allows you to change the output power to low. Press this button to change the output power to Low. • Beep A (1 beep) sounds. Press this button again to change the transmit power to
  • Kenwood NX-P1200AV | User Manual - Page 41
    Scrambler/ Encryption Enables or disables Scrambler (Analog) or Encryption (Digital) function. • Voice Scrambler is the function to scramble the audio signal so that the contents of communications can be prevented from being intercepted. • Encryption is the function that enhances secrecy in
  • Kenwood NX-P1200AV | User Manual - Page 42
    Super Lock This function prevents the user from mistakenly changing channels or stopping scan through unexpected operation. When the transceiver is locked, changing of zone or channel is not allowed even if the selector knob is turned to another zone or channel. Press and hold this button for 4
  • Kenwood NX-P1200AV | User Manual - Page 43
    OTHER PROGRAM FUNCTIONS The following program functions are set by your dealer. SECOND PTT By pressing this button, you can use the same operation as PTT switch to move to a different channel (Second PTT Channel) from the standby channel and transmit. • Second PTT Channel can be set for each zone. •
  • Kenwood NX-P1200AV | User Manual - Page 44
    VOICE OPERATED TRANSMISSION (VOX) VOX (VOX/ Semi-VOX) operation allows you to transmit hands-free. This feature can be enabled by your dealer. To operate VOX, you must use an optional headset. VOX Type VOX: When the voice level to the microphone is higher than the reference level (VOX Gain Level),
  • Kenwood NX-P1200AV | User Manual - Page 45
    5 Press the PTT switch to save the settings. • Beep A (1 beep) will sound. • The transceiver announces the new VOX Gain level. 6 Turn the transceiver power OFF and then ON again to activate VOX. Note: ◆ If a headset is connected to the transceiver while the VOX function is switched ON and the VOX
  • Kenwood NX-P1200AV | User Manual - Page 46
    BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer prevent callers from using a channel for an extended duration. If you continuously transmit for the duration programmed by your dealer (default is 60 seconds), transmission will stop and an alert tone will sound. To stop the tone, release
  • Kenwood NX-P1200AV | User Manual - Page 47
    VOICE ANNOUNCEMENT An audio voice will be announced. • When changing the zone and/or channel, the new zone and channel number are announced. • When changing the function on/ off, the new settings is announced. - Encryption - Scrambler - Home Channel - Button Lock - Low Transmit Power - Scan -
  • Kenwood NX-P1200AV | User Manual - Page 48
    ALL RESET MODE At some point in time, you may desire to reset the transceiver settings to their default values. The following settings will return to the default values. • Self-programming Mode • Button Function Programming Mode • VOX Function Setup Mode 1 With the transceiver power OFF, press and
  • Kenwood NX-P1200AV | User Manual - Page 49
    TROUBLESHOOTING GUIDE Problem Cannot turn the transceiver power ON. Solution The battery pack may be dead. Recharge or replace the battery pack. Ref. page � The battery pack may
  • Kenwood NX-P1200AV | User Manual - Page 50
    SPECIFICATIONS Transmit Power NX-P1200NV NX-P1200AV NX-P1300NU NX-P1300AU 5 / 4 / 1 W NX-P1202AV NX-P1302AU 2 / 1 W Audio Output 1 W / 12 Ω (Internal Speaker) 500 mW / 8 Ω (External Output) Operating Voltage 7.5 V DC ±20 % Operating Temperature Range Frequency Stability -30°C (-22°F)~ +60
  • Kenwood NX-P1200AV | User Manual - Page 51
    © 2020
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
USER MANUAL
NX-P1200NV
NX-P1200AV
NX-P1202AV
NX-P1300NU
NX-P1300AU
NX-P1302AU
B5A-3583-00_EN