Home » Kenwood Manuals » Electronics Accessories » Kenwood TK-2170 » Manual Viewer

Kenwood TK-2170 User Manual

Kenwood TK-2170 Manual

Get Kenwood TK-2170 PDF manuals and user guides

View all Kenwood TK-2170 manuals

Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-2170 manual content summary:

Kenwood TK-2170 | User Manual - Page 1
TK-2170/ TK-2170ST/ TK-3170 VHF FM TRANSCEIVER/ VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL VHF FM VHF FM UHF FM VHF VHF UHF © B62-1810-00 (M) 09 08 07 06 05 04 03 02 01 00
Kenwood TK-2170 | User Manual - Page 2
ENGLISH VHF FM TRANSCEIVER/ VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-2170/ TK-2170ST/ TK-3170 INSTRUCTION MANUAL
Kenwood TK-2170 | User Manual - Page 3
features of this product. MODELS COVERED BY THIS MANUAL • TK-2170: VHF FM Transceiver • TK-2170ST: VHF FM Transceiver • TK-3170: UHF FM Transceiver NOTICES TO THE USER ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal
Kenwood TK-2170 | User Manual - Page 4
battery pack. • Do not use options not specified by KENWOOD. • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts surfaces. • Ensure that the end of the antenna does not touch your eyes. • When the replacing the battery pack. • Do not immerse
Kenwood TK-2170 | User Manual - Page 5
parts are exposed from the antenna covering. Transmitting at such a time may result in a high-frequency burn. • If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery pack from the transceiver, and contact your KENWOOD
Kenwood TK-2170 | User Manual - Page 6
ACCESSORIES 1 PREPARATION 2 BATTERY PACK PRECAUTIONS 2 INSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK OR BATTERY CASE ....... 7 INSTALLING/ REMOVING ALKALINE BATTERIES 8 INSTALLING THE (OPTIONAL) ANTENNA CHANNEL/ GROUP ID 17 TRUNKING ZONES (TK-3170 ONLY 18 PLACING A DISPATCH CALL 18
Kenwood TK-2170 | User Manual - Page 7
SCAN 26 PRIORITY SCAN 26 GROUP SCAN (TK-3170 ONLY 26 SCAN REVERT 27 FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION 28 SELCALL (SELECTIVE CALLING 28 STATUS MESSAGE 29 SHORT MESSAGES 31 LONG MESSAGES 31 DTMF (DUAL TONE MULTI FREQUENCY) CALLS 32 MANUAL DIALING 32 STORE AND SEND 33 AUTODIAL
Kenwood TK-2170 | User Manual - Page 8
: The following unpacking instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the the carrier immediately. SUPPLIED ACCESSORIES Item Belt clip Speaker/ microphone jacks cap Speaker/ microphone locking bracket Instruction manual Part Number J29-0701-XX B09
Kenwood TK-2170 | User Manual - Page 9
the battery pack or transceiver using a dry cloth before charging. ◆ Do not short the battery terminals or dispose of the battery by fire. ◆ Never attempt to remove the casing from the battery pack. ■ CHARGING THE BATTERY PACK For charging procedures, refer to the battery charger Instruction Manual
Kenwood TK-2170 | User Manual - Page 10
melted, the gas release vent or safety function is damaged, or the electrolyte is ignited, the battery may generate heat or smoke, rupture, or burst into flame. • Do not use or leave the battery near fires, stoves, or other heat generators (areas reaching over 80°C/ 176°F)! If the polymer separator
Kenwood TK-2170 | User Manual - Page 11
regulated value, or with a remodelled charger), it may overcharge or an abnormal chemical reaction may occur. The battery may generate heat or smoke, rupture, or burst into flame. • Do not pierce the battery with any object, strike it with an instrument, or step on it! This may break or deform the
Kenwood TK-2170 | User Manual - Page 12
water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems. • Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time has passed, stop it. The
Kenwood TK-2170 | User Manual - Page 13
the equipment when it is not in use. Store the battery pack in a cool and dry location. • When storing the battery pack for a long period: 1 Remove the battery pack from the equipment. 2 Discharge the battery pack, if possible. 3 Store the battery pack in a cool (below 25°C/ 77°F) and dry location
Kenwood TK-2170 | User Manual - Page 14
imperative that you place the implement under only the lip of the safety catch so that you do not damage the release latch. ◆ Before charging a battery pack that is attached to the transceiver, ensure that the safety catch is firmly closed. ◆ While operating the transceiver using a Li-ion or Ni-MH
Kenwood TK-2170 | User Manual - Page 15
setting on your transceiver). If you want to transmit a stronger signal (using the high power setting on your transceiver), use an optional rechargeable battery pack. 1 To open the battery case, press on the two tabs on the upper rear of the case, then pull the two halves apart. 2 Insert 6 AA (LR6
Kenwood TK-2170 | User Manual - Page 16
retainer, nor a speaker/ microphone attachment point. Using the antenna in these ways may damage the antenna and degrade your transceiver's performance. INSTALLING THE BELT CLIP Note: When first installing the belt clip, you must remove the battery pack from the rear of the transceiver. 1 Remove the
Kenwood TK-2170 | User Manual - Page 17
INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS Install the cap over the speaker/ microphone jacks when not using an optional speaker/ microphone. 1 Place the cap over the jacks so that the locking tabs insert into the transceiver grooves. 2 While holding the cap in place, push it towards the
Kenwood TK-2170 | User Manual - Page 18
GETTING ACQUAINTED qw e t r y Microphone u i o !0 Speaker !1 !3 !2 q Antenna connector Connect an (optional) antenna here {page 9}. w Selector Rotate to activate its programmable function {page 15}. e Power switch/ Volume control Turn clockwise to switch ON the transceiver. Rotate to adjust
Kenwood TK-2170 | User Manual - Page 19
Lights green while receiving a call. Flashes orange while receiving an encoded (2-tone, DTMF signaling, etc.) call. If programmed by your dealer, flashes red when the battery power is low while transmitting. t Safety Catch Lock this catch to avoid accidentally pressing the release latch and removing
Kenwood TK-2170 | User Manual - Page 20
while scanning. Lights when a message is stored in the stack memory. Flashes when you receive a new message. Appears when the selected channel is programmed as priority. TK-3170 Only: Appears when the selected group is programmed as telephone IDs. Flashes when performing an auto telephone search. 13
Kenwood TK-2170 | User Manual - Page 21
activated. Displays the battery status. The battery icon with all 3 strength bars represents full power while an empty battery icon represents very low Displays the zone, group ID, and channel numbers. Your dealer can program zone, group ID, and channel names with up to 8 characters, in place
Kenwood TK-2170 | User Manual - Page 22
Group Code Select 3 • VOX • Zone Down • Zone Up 1 "Auto Telephone" and "Telephone Disconnect" are available only for the TK-3170 transceiver. 2 "Emergency" can be programmed only on the Auxiliary (orange) key. 3 "Trunking Group Code Select" is available only when the Trunking board has been
Kenwood TK-2170 | User Manual - Page 23
OPERATING BASICS OVERVIEW Your dealer can program your transceiver with Conventional Zones. (TK-3170 transceivers can be programmed with Trunking Zones and Conventional Zones.) The transceiver can handle up to 128 zones with up to 128 channels/ 250 group IDs. Zones, channels/ group
Kenwood TK-2170 | User Manual - Page 24
display. For example, if the channel/ group ID name is "GRP 1" and the zone name is "KENWOOD", and your dealer sets the zone name to 3-digits, the following display will appear: Press the key programmed as Display Character to toggle the display between the zone and channel/ group ID number and the
Kenwood TK-2170 | User Manual - Page 25
TRUNKING ZONES (TK-3170 ONLY) PLACING A DISPATCH CALL 1 Press and hold the PTT switch. 2 If the "Proceed" tone sounds, communication is possible; speak into the microphone to make your
Kenwood TK-2170 | User Manual - Page 26
after you release the PTT switch. 3 Place the call, following the instructions for making a DTMF call, starting on page 32. 4 When the press and hold the PTT switch, then press the # key or the key programmed as Telephone Disconnect. RECEIVING A TELEPHONE CALL 1 When a telephone call is received,
Kenwood TK-2170 | User Manual - Page 27
SmarTrunk OPERATION Note: SmarTrunk and SmarTrunk II are registered trademarks of SmarTrunk Systems, Inc., Hayward, California, U.S.A. TK-2170ST transceivers are SmarTrunk ready. On other transceivers, you must install the appropriate trunking board before you can access SmarTrunk Trunking mode.
Kenwood TK-2170 | User Manual - Page 28
on if desired. 2 When you hear a caller's voice, readjust the volume as necessary. QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) Your dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to ignore (not hear) calls
Kenwood TK-2170 | User Manual - Page 29
display. (This indicator will not appear on TK-3170 transceivers if it has been set to store Trunking zone data.) • The LED indicator flashes orange. • To mute the speaker after squelch opens, press the key programmed as Monitor. • Your dealer can program the squelch to close again after a specific
Kenwood TK-2170 | User Manual - Page 30
display when To change the preset encode/decode tones: 1 Press and hold the key programmed as OST for approximately 1 second. • The OST name appears on the display. hands-free. This feature can only be used if you are using a supported headset. When operating VOX, you must set a VOX Gain level.
Kenwood TK-2170 | User Manual - Page 31
activate when a headset is not connected to the speaker/ microphone jack of the transceiver. 2 Press and hold the key programmed as VOX for 2 seconds. • The VOX indicator ( ) appears on the display. 3 To turn the VOX function , you must use an optional KHS-1, KHS-21, or KHS-22 accessory. 24
Kenwood TK-2170 | User Manual - Page 32
, zones or channels can be scanned by pressing the key programmed as Scan. Scan can be used as either Single Scan, Multi Scan, or List Scan (TK-3170 only). • Single Scan monitors only the channels of the currently selected zone, which have been added to the scanning sequence. If set up to scan
Kenwood TK-2170 | User Manual - Page 33
the group ID of a Trunking zone; it can be used only on channels of Conventional zones. GROUP SCAN (TK-3170 ONLY) Group Scan is useful when more than one group ID is programmed in a zone. Group Scan is set by your dealer on request. It scans the revert groups as well as groups
Kenwood TK-2170 | User Manual - Page 34
ID is the zone and channel/ group ID which the transceiver automatically selects when pressing the PTT switch during Scan, to transmit. Your dealer can program 1 of 6 types of Scan Reverts for your transceiver: • Last Called: The last zone and channel/ group ID received is assigned as the new revert
Kenwood TK-2170 | User Manual - Page 35
by KENWOOD Corporation. FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming. SELCALL . • Alternatively, press and hold the S or key to enter Manual Dialing mode. Using Manual Dialing, you can enter digits with the DTMF keypad or selector.
Kenwood TK-2170 | User Manual - Page 36
to all units (Broadcast call). Note: The ID range may be limited by programming. STATUS MESSAGE You can send and receive 2-digit Status messages which may be the stack memory of your transceiver. These saved messages can be reviewed after reception. Depending on your dealer settings, when the stack
Kenwood TK-2170 | User Manual - Page 37
• Alternatively, press and hold the S or key to enter Manual Dialing mode. Using Manual Dialing, you can enter digits with the DTMF keypad or selector Alternatively, press the Call 1 or Call 2 key to transmit their pre-programmed status messages. •" " appears on the display when the call has been
Kenwood TK-2170 | User Manual - Page 38
■ REVIEWING MESSAGES IN THE STACK MEMORY 1 Press and hold the key programmed as Selcall, Status, or Selcall + Status for 1 second to enter Stack Mode. • The last received call ID/ stack number appears on the display. 2 Press the
Kenwood TK-2170 | User Manual - Page 39
DTMF (DUAL TONE MULTI FREQUENCY) CALLS MANUAL DIALING ■ METHOD 1 Press and hold the PTT switch DTMF code is transmitted after a connection with the telephone system is established. Press the key programmed as Autodial, followed by the Side 2 key, to automatically connect to the repeater and transmit
Kenwood TK-2170 | User Manual - Page 40
up to 16 digits per number). These operations can be performed with or without a DTMF keypad. ■ STORING DTMF NUMBERS 1 Press the key programmed as Autodial Programming. • If programmed by your dealer, you can also press and hold the # key for 1 second. • The first entry in the Autodial list appears
Kenwood TK-2170 | User Manual - Page 41
store the entered name and number in the Autodial list. • Press the A or # key to cancel the entry. ■ DIALING STORED DTMF NUMBERS 1 Press the key programmed as Autodial. • If programmed by your dealer, you can also press the # key. • The first entry in the Autodial list appears on the display. 34
Kenwood TK-2170 | User Manual - Page 42
PTT switch to make the call or the Side 2 key to page the selected recipient. ■ CLEARING STORED DTMF NUMBERS 1 Press the key programmed as Autodial Programming. • If programmed by your dealer, you can also press and hold the # key for 1 second. 2 Press the keys, rotate the selector, or
Kenwood TK-2170 | User Manual - Page 43
display. (This indicator will not appear on TK-3170 transceivers if it has been set to store Trunking zone data.) • The LED indicator flashes orange. • To mute the speaker after squelch opens, press the key programmed as Monitor. • Your dealer can program the squelch to close again after a specific
Kenwood TK-2170 | User Manual - Page 44
function, you can make emergency calls. Note: Only the Auxiliary (orange) key can be programmed with the Emergency function. 1 Press and hold the key programmed as Emergency. • Depending on the delay time programmed into your transceiver, the length of time you must hold the Emergency key will vary
Kenwood TK-2170 | User Manual - Page 45
conserves battery power and reduces the risk of interfering with other communications. Note: Pressing Low Transmit Power while using a channel programmed with low power causes an error tone to sound. TALK AROUND You may occasionally experience an interruption in service (due
Kenwood TK-2170 | User Manual - Page 46
no signals are present on your selected channel. • The icon appears on the display while Monitor/ Squelch Off is activated. Your dealer can program a key with one of 4 functions: • Monitor: Momentarily press to deactivate QT, DQT, DTMF, 2-tone, or Fleetsync Signaling. Press the key again to return
Kenwood TK-2170 | User Manual - Page 47
while transmitting and corrects the voice message on your own transceiver when you receive the call. To activate the scrambler, press the key programmed as Scrambler. • The icon appears on the display while the scrambler is active. To deactivate the scrambler, press the Scrambler key again. Note
Kenwood TK-2170 | User Manual - Page 48
ID: 1 Select a frequently used channel/ group ID. 2 Press and hold the key programmed as Home CH/GID or Direct CH/GID (1 ~ 4) for approximately 3 seconds to store stored. To use the Home CH/GID key, press it to jump to the programmed channel/ group ID. You can press this key a second time to return
Kenwood TK-2170 | User Manual - Page 49
channel/ group ID number. For example, to select channel/ group ID 5, enter "5" on your keypad. • If up to 99 channels/ group IDs have been programmed on your transceiver, enter a 2-digit channel/ group ID number. For example, to select channel/ group ID 5, enter "05" on your keypad. • If over 100
Kenwood TK-2170 | User Manual - Page 50
sound. To stop the tone, release the PTT switch. Your dealer can program the TOT time in the range of 15 seconds to 20 minutes for QT, DQT, DTMF, 2-tone, or FleetSync signaling. BATTERY SAVER If activated by your dealer, the Battery Saver function will decrease the amount of power used when
Kenwood TK-2170 | User Manual - Page 51
pack. If activated by your dealer, an alert tone will sound every 30 seconds and the LED indicator will blink red when the battery power is low. BEGINNING/ END OF TRANSMIT SIGNAL The Beginning of Transmit and End of Transmit identification signals are used to access and release some