Kenwood TK-2317 Operation Manual
Kenwood TK-2317 Manual
View all Kenwood TK-2317 manuals
Add to My Manuals
Save this manual to your list of manuals |
Kenwood TK-2317 manual content summary:
- Kenwood TK-2317 | Operation Manual - Page 1
INSTRUCTION MANUAL VHF FM TRANSCEIVER TK-2317 UHF FM TRANSCEIVER TK-3317 © B62-2237-10 (M) 09 08 07 06 05 04 03 02 01 - Kenwood TK-2317 | Operation Manual - Page 2
- Kenwood TK-2317 | Operation Manual - Page 3
you have chosen KENWOOD for your land mobile radio applications. NOTICES TO THE USER ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified - Kenwood TK-2317 | Operation Manual - Page 4
they are wet. • Ensure that there are no metallic items located between the transceiver and the battery pack. • Do not use options not specified by KENWOOD. • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts. • If a headset or headphone is connected to the - Kenwood TK-2317 | Operation Manual - Page 5
at gasoline service stations. • Near explosives or blasting sites. • In aircrafts. (Any use of the transceiver must follow the instructions and regulations immediately, remove the battery pack from the transceiver, and contact your KENWOOD dealer. • Use of the transceiver while you are driving may - Kenwood TK-2317 | Operation Manual - Page 6
Information concerning the battery pack: The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters. • - Kenwood TK-2317 | Operation Manual - Page 7
• Use only the specified charger and observe charging requirements! If the battery is charged in unspecified conditions (under high temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodeled charger), it may overcharge or an abnormal chemical - Kenwood TK-2317 | Operation Manual - Page 8
your eyes with fresh water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems. • Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time has - Kenwood TK-2317 | Operation Manual - Page 9
CONTENTS UNPACKING AND CHECKING EQUIPMENT 1 SUPPLIED ACCESSORIES 1 PREPARATION 2 INSTALLING/ REMOVING THE BATTERY PACK 2 INSTALLING THE ANTENNA 3 INSTALLING THE BELT CLIP 3 INSTALLING THE SPEAKER/ MICROPHONE JACKS COVER.....4 INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET 4 CHARGING - Kenwood TK-2317 | Operation Manual - Page 10
SIGNALING 16 OPTIONAL SIGNALING 16 OPERATOR SELECTABLE TONE (OST 16 FleetSync 17 SELCALL (SELECTIVE CALLING 17 STATUS MESSAGES 18 SHORT MESSAGES 19 VOICE OPERATED TRANSMISSION (VOX 20 VOX OPERATION 20 VOX GAIN LEVEL 20 ADVANCED OPERATIONS 21 TRANSMIT POWER 21 CALLING ALERT 21 KEY LOCK - Kenwood TK-2317 | Operation Manual - Page 11
with the carrier immediately. SUPPLIED ACCESSORIES • Speaker/ microphone jack cover 1 • Speaker/ microphone locking bracket 1 • Belt clip (KBH-10 1 • Screw set M2.6 x 7 mm (black 1 M3 x 8 mm 2 • Instruction manual 1 Note: Refer to "PREPARATION" {page 2} for accessory installation - Kenwood TK-2317 | Operation Manual - Page 12
PREPARATION INSTALLING/ REMOVING THE BATTERY PACK (OPTION) ◆ Do not short the battery terminals or dispose of the battery by fire. ◆ Never attempt to remove the casing from the battery pack. 1 Align the battery pack with the back of the transceiver, then press the battery pack and transceiver firmly - Kenwood TK-2317 | Operation Manual - Page 13
INSTALLING THE ANTENNA (OPTION) Antenna Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. Note: The antenna is neither a handle, a key ring retainer, nor a speaker/ microphone attachment point. Using the - Kenwood TK-2317 | Operation Manual - Page 14
INSTALLING THE SPEAKER/ MICROPHONE JACKS COVER If you are not using a speaker/ microphone, install the cover over the speaker/ microphone jacks using the supplied M2.6 x 7 mm screw. Note: To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cover. - Kenwood TK-2317 | Operation Manual - Page 15
CHARGING THE BATTERY PACK (OPTION) The battery pack is not charged at the factory; charge it before use. ATTENTION: Always switch OFF a transceiver equipped with a battery pack before inserting the transceiver into the charger. 1 Plug the AC adapter cable into the jack on the rear of the charger. - Kenwood TK-2317 | Operation Manual - Page 16
Antenna ORIENTATION Speaker Battery pack Microphone Selector Rotate to change the operating zone or channel. The default setting is [Zone Up/ Down]. LED indicator Refer to the table on page 7 for the LED indicator status. Power switch/ Volume control Turn clockwise to switch the transceiver ON. To - Kenwood TK-2317 | Operation Manual - Page 17
S, A, keys Press to activate their programmable functions. S key: The default setting is [None] (no function). A key: The default setting is [None] (no function). key: The default setting is [Channel Up]. , , keys Press to activate their - Kenwood TK-2317 | Operation Manual - Page 18
DISPLAY Indicator Description Displays the strength of received signals {page 25}. Appears when the Monitor or Squelch Off function has been activated. Appears when using DTMF or QT/DQT + Optional Signaling. Appears while using the Talk Around function. Appears while scanning. Appears when a - Kenwood TK-2317 | Operation Manual - Page 19
Indicator Description Displays the current battery status {page 25}. The selected zone is added to the scanning sequence. The selected channel is added to the scanning sequence. Appears while using the VOX function. Displays the zone and channel number or name as well as FleetSync messages and DTMF - Kenwood TK-2317 | Operation Manual - Page 20
PROGRAMMABLE AUXILIARY FUNCTIONS The Side 1, Side 2, S, A, , , , and keys can be programmed with the functions listed below. Please contact your dealer for further details on these functions. Note: The Selector can be programmed as either [Zone Up/Down] or [Channel Up/Down]. • None (No - Kenwood TK-2317 | Operation Manual - Page 21
BASIC OPERATIONS SWITCHING POWER ON/ OFF Turn the Power switch/ Volume control clockwise to switch the transceiver ON. • A beep sounds and the display momentarily lights up. • If the Transceiver Password function is programmed, "PASSWORD" appears on the display. Enter the password to unlock the - Kenwood TK-2317 | Operation Manual - Page 22
SELECTING A ZONE AND CHANNEL Select the desired zone using the Selector or the keys programmed as [Zone Up]/ [Zone Down]. • The default setting for the Selector is [Zone Up/ Down]. Select the desired channel using the Selector or the keys programmed as [Channel Up]/ [Channel Down]. • The default - Kenwood TK-2317 | Operation Manual - Page 23
SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a matching signal is present. To start/stop scanning, press the key programmed as [Scan]. • The indicator appears during Scan. • When a signal is detected - Kenwood TK-2317 | Operation Manual - Page 24
SCAN DELETE/ADD You can add and remove zones and/or channels to and from your scan list. 1 Select your desired zone and/or channel. 2 Press the key programmed as [Scan Delete/Add] to remove a channel or press and hold the key for approximately 1 second to remove a zone. • The channel add - Kenwood TK-2317 | Operation Manual - Page 25
DTMF CALLS AUTODIAL Autodial allows you to quickly call DTMF numbers that have been programmed onto your transceiver. 1 Press the key programmed as [Autodial]. • The last called number appears. 2 Press to select your desired Autodial list number. 3 Press the PTT switch to make the call. • - Kenwood TK-2317 | Operation Manual - Page 26
SIGNALING Quiet Talk (QT)/ Digital Quiet Talk (DQT): Your dealer may have programmed QT or DQT signaling on your transceiver channels. QT and DQT signals allow you to ignore (not hear) calls from other parties who are using the same channel. MDC-1200: MDC-1200 is a data system using Audio Frequency - Kenwood TK-2317 | Operation Manual - Page 27
FleetSync FleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by JVC KENWOOD Corporation. Note: If set up by your dealer, your transceiver may use the MDC-1200 feature in place of FleetSync. MDC-1200 and FleetSync cannot - Kenwood TK-2317 | Operation Manual - Page 28
STATUS MESSAGES You can transmit pre-programmed status messages by pressing the keys programmed as [Status] and [Selcall + Status]. Status messages are 2-digit codes ranging from 10 to 99 (80 ~ 99 are reserved for special messages). ■ Transmitting 1 Select your desired zone and channel. 2 Press the - Kenwood TK-2317 | Operation Manual - Page 29
■ Reviewing Messages in the Stack Memory 1 Press and hold the key programmed as [Selcall], [Status], or [Selcall + Status] for 1 second to enter the Stack memory. • The last received message is displayed with the message number. 2 Press to select the desired message. • Press and hold S to - Kenwood TK-2317 | Operation Manual - Page 30
VOICE OPERATED TRANSMISSION (VOX) VOX operation allows you to transmit hands-free. This feature can be activated or deactivated by your dealer. VOX OPERATION 1 Press and hold the key programmed as [VOX] for 2 seconds to turn the VOX function ON (or OFF). • The VOX indicator ( function is ON. ) - Kenwood TK-2317 | Operation Manual - Page 31
ADVANCED OPERATIONS TRANSMIT POWER Each channel is programmed with either high or low transmit power. On high transmit power channels, press the key programmed as [Low Transmit Power] to change the transmit power to low power (you cannot change low transmit power channels to use high power). • The - Kenwood TK-2317 | Operation Manual - Page 32
and hold the key programmed as [Lone Worker] for 2 seconds to toggle the Lone Worker function ON or OFF. TALK AROUND During interruptions in service (such as a power failure), you can continue to communicate by using the Talk Around feature. Talk Around allows you to communicate directly with other - Kenwood TK-2317 | Operation Manual - Page 33
. The scrambler function will not work with transceivers set up with different scrambler codes. Note: This function cannot be used in certain countries. Contact your KENWOOD dealer for further information. 23 - Kenwood TK-2317 | Operation Manual - Page 34
MONITOR/ SQUELCH OFF You can use the key programmed as [Monitor] or [Squelch Off] to listen to weak signals that you cannot hear during normal operation and to adjust the volume when no signals are present on your selected channel. Your dealer can program a key with one of 4 functions: • Monitor: - Kenwood TK-2317 | Operation Manual - Page 35
BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer prevents you from using a channel for an extended duration. If you continuously transmit for a preset time, the transceiver will stop transmitting and an alert tone will sound. Release the PTT switch. BATTERY SAVER When activated by your - Kenwood TK-2317 | Operation Manual - Page 36
BUSY CHANNEL LOCKOUT (BCL) If BCL is set up by your dealer, you will be unable to transmit if the channel is already in use. Use a different channel or wait until the channel becomes free. COMPANDER If programmed by your dealer for a channel, the compander will remove excessive noise from - Kenwood TK-2317 | Operation Manual - Page 37
TK-2317 TK-3317 - Kenwood TK-2317 | Operation Manual - Page 38
- Kenwood TK-2317 | Operation Manual - Page 39
KENWOOD KENWOOD JVC KENWOOD Corporation. i - Kenwood TK-2317 | Operation Manual - Page 40
KENWOOD ii - Kenwood TK-2317 | Operation Manual - Page 41
KENWOOD iii - Kenwood TK-2317 | Operation Manual - Page 42
80°C iv - Kenwood TK-2317 | Operation Manual - Page 43
v - Kenwood TK-2317 | Operation Manual - Page 44
vi - Kenwood TK-2317 | Operation Manual - Page 45
1 1 2 2 3 3 4 4 5 6 8 10 11 11 11 12 12 12 13 13 13 14 14 DTMF 15 15 vii - Kenwood TK-2317 | Operation Manual - Page 46
15 DTMF 15 16 16 OST 16 FLEETSYNC 17 SELCALL 17 18 19 VOX 20 VOX 20 20 21 21 21 21 22 22 23 24 24 24 25 TOT 25 25 25 25 BCL 26 26 PTT ID 26 viii - Kenwood TK-2317 | Operation Manual - Page 47
1 1 KBH-10 1 M2.6 x 7 1 M3 x 8 2 1 2}. 1 - Kenwood TK-2317 | Operation Manual - Page 48
1 2 3 2 - Kenwood TK-2317 | Operation Manual - Page 49
M3 x 8 мм. 3 - Kenwood TK-2317 | Operation Manual - Page 50
M2.6 x 7 мм. 1 2 M2.6 x 7 мм. 4 - Kenwood TK-2317 | Operation Manual - Page 51
1 2 3 4 3 часа. 5°C до 40°C 5 - Kenwood TK-2317 | Operation Manual - Page 52
7 PTT (Push to Talk 1 6 - Kenwood TK-2317 | Operation Manual - Page 53
2 S, A, S A B C Мигает FleetSync, DTMF и т.д.) FleetSync, DTMF или 2 7 - Kenwood TK-2317 | Operation Manual - Page 54
25}. DTMF или QT DQT 8 - Kenwood TK-2317 | Operation Manual - Page 55
25}. FleetSync DTMF. 9 - Kenwood TK-2317 | Operation Manual - Page 56
1 2, S, A, - Kenwood TK-2317 | Operation Manual - Page 57
PASSWORD 1 2 C A 3 1 и 2 6 цифр. 4 S PF 11 - Kenwood TK-2317 | Operation Manual - Page 58
B C 8 1 2 3 PTT 3 - 4 4 PTT ПРИЁМ 1 2 12 - Kenwood TK-2317 | Operation Manual - Page 59
2 13 - Kenwood TK-2317 | Operation Manual - Page 60
1 2 1 PTT 14 - Kenwood TK-2317 | Operation Manual - Page 61
DTMF DTMF 1 2 B или C 3 PTT S STUN". DTMF DTMF DTMF 3 1 1 DTMF. 15 - Kenwood TK-2317 | Operation Manual - Page 62
QT DQT QT или DQT QT и DQT MDC-1200: MDC-1200 AFSK). 2 2 2 DTMF Signaling DTMF DTMF FleetSync: См. "SELCALL 17. OST 40 пар OST. 1 2 OST OST. OST OST. 3 B или C OST. 4 PTT 5 OST S. 16 - Kenwood TK-2317 | Operation Manual - Page 63
FleetSync FleetSync JVC KENWOOD Corporation. FleetSync MDC-1200 MDC-1200 и FleetSync SELCALL Selcall 1 2 3 B или C 4 PTT 2 PTT 3 Fleet и 4 Fleet 17 - Kenwood TK-2317 | Operation Manual - Page 64
2 10 до 99 (80 - 99 1 2 Fleet 5 3 B или C 4 S 5 B или C 6 PTT 2 COMPLETE". 18 - Kenwood TK-2317 | Operation Manual - Page 65
1 1 2 B или C S 3 1 A S A 1 S. 48 3 5 ОТЧЁТ GPS GPS GPS 2 19 - Kenwood TK-2317 | Operation Manual - Page 66
VOX) VOX VOX) 1 VOX 2 ). 2 3 4 1 VOX 2 B или C 1 10 5. 3 4 S 20 - Kenwood TK-2317 | Operation Manual - Page 67
1 2 PTT 2 LOCKED". PTT. GPS GPS. 21 - Kenwood TK-2317 | Operation Manual - Page 68
1 2 2 22 - Kenwood TK-2317 | Operation Manual - Page 69
1 1 2 B или C 3 S KENWOOD 23 - Kenwood TK-2317 | Operation Manual - Page 70
4 1 SQL.LVL 2 B или C 0 9 3 S 5 PTT 5 24 - Kenwood TK-2317 | Operation Manual - Page 71
TOT PTT. 5 QT/DQT QT/DQT Низкий 30 Слабая 25 - Kenwood TK-2317 | Operation Manual - Page 72
BCL BCL PTT ID PTT ID PTT. 26
INSTRUCTION MANUAL
© B62-2237-10 (M)
09 08 07 06 05 04 03 02 01
VHF FM TRANSCEIVER
TK-2317
UHF FM TRANSCEIVER
TK-3317